• 열처리공학회지
• /
• 제34권3호
• /
• pp.107-115
• /
• 2021

Al-Si coated boron steel has been widely used as commercial hot stamping steel. When the steel is heated at 900~930℃ for 5 min in an electric furnace, thickness of the coating layer increases as a consequence of formation of intermetallic compounds and diffusion layer. The diffusion layer plays an important roll in blunting the propagation of crack from coating layer to base steel. Change in microstructure and coating layer of Al-Si coated boron steel after conductive heating with higher heating rate than electric furnace has been investigated in this study. Conductive-heated steel showed the martensitic structure with vickers hardness of 505~567. Both intermetallic compounds in coating layer and diffusion layer were not observed in conductive-heated steel due to rapid heating. It has been found that the conductive-heating consisting of rapid heating to 550℃ which is lower than melting point of Al-Si coating layer, slower heating to 900℃, and then 1 min holding at 900℃ is effective in forming intermetallic compound in coating layer and diffusion layer.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2011년도 춘계 학술논문 발표대회 1부
• /
• pp.39-40
• /
• 2011

The purpose of this study is to select a conductive resistor as high energy efficiency through analysis of the heating properties by induction heating. The result of this study, the heating properties is capable of weaken cementitious joint in 10~30 seconds when using the conductive resistor with wire mesh or punching metal. Although the steel is higher temperature than SUS304, SUS304's heating properties are more uniform.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2014년도 추계 학술논문 발표대회
• /
• pp.131-132
• /
• 2014

In this study, an experiment was carried out using graphite, conductive nickel powder, copper bar, carbon fiber for evaluate the exothermic properties and heating reproducibility of the cement mortar containing conductive material. As a result, the conductive materials that interfere with heating reproducibility are present, and the optimal conductive materials exist in each input voltage.

• 한국전기전자재료학회논문지
• /
• 제33권6호
• /
• pp.500-504
• /
• 2020

Heating films were prepared with composites of poly (methyl methacrylate) and conductive graphite. The as-prepared composite was deposited on a PET film and then fabricated using a bar coater to produce a film with uniform thickness. Copper electrodes were attached to both ends of the as-prepared film, and the heating characteristics of the film were analyzed while applying a DC voltage. The electrical conductivity and heating temperature of the heating films depended on the size, structure, content, and the dispersion characteristics of the graphite in the composite. The thermal energy was adjusted by controlling the electrical energy, based on the Joule heating theory. The electrical resistance of the film was altered in proportion to Ohm's law, and the heating temperature was changed according to the structure of the film (interelectrode spacing or electrode length) and the conductive graphite content. When the content of conductive graphite in the film increases, the electrical resistance decreases, and the heating temperature increases; however, there is no significant change above a certain content (50%).

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2003년도 춘계학술발표대회 개요집
• /
• pp.111-113
• /
• 2003

The existing heating unit is indirect-heating method that make use or the nichrome wire or halogen lamp. The indirect-heating method has the demerits of long warming time, high power consumption and many organization parts. In this study, the heating unit of direct-heating method manufactured as being the thermal spray coating of conductive heating material on the surface of heating unit in order to improve the demerits of indirect-heating method. And YSZ added Ni-20Cr that had moderate electrical resistivity was chosen of the conductive heating material.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2011년도 춘계 학술논문 발표대회 1부
• /
• pp.3-4
• /
• 2011

The purpose of this study is to suggest basic data for development optimal disassembly manufacturing system during analysis pore structure and heating properties of cementitious joint using conductive resister by induction heating. From the results, we knew cementitious joint is weak easily by heating of conductive resister, such as wire mesh, punching metal, and steel fiber, from induction heating.

• 한국표면공학회지
• /
• 제46권4호
• /
• pp.162-167
• /
• 2013

Encapsulation is required since organic materials used in OLED devices are fragile to water vapor and oxygen. Laser sealing method is currently used where IR laser is scanned along the glass-frit coated lines. Laser method is, however, not suitable to encapsulating large-sized glass substrate due to the nature of sequential scanning. In this work we propose a new method of encapsulation using Joule heating. Conductive layer is patterned along the sealing lines on which the glass frit is screen printed and sintered. Electric field is then applied to the conductive layer resulting in bonding both the panel glass and the encapsulation glass by melting glass-frit. In order to obtain uniform bonding the temperature of a conductive layer having a shape of closed loop should be uniform. In this work we conducted simulation for heat distribution according to the structure of a conductive layer used as a Joule-heat source. Uniform temperature was obtained with an error of 5% by optimizing the structure of a conductive layer. Based on the results of thermal simulations we concluded that Joule-heating induced encapsulation would be a good candidate for encapsulation method especially for large area glass substrate.

• Journal of Welding and Joining
• /
• 제25권4호
• /
• pp.28-34
• /
• 2007

The heating unit of direct heating method manufactured as the plasma spray coating of $TiO_2/NiCr$ conductive heating material on the surface of heating unit in order to improve the disadvantages of indirect heating method. $TiO_2$ and NiCr (80wt.%Ni-20wt.%Cr) that had the properties of conduction and heating was chosen for the conductive heating material. The compositions of the composite powders were studied $TiO_2-30wt.%NiCr\;and\;TiO_2-10wt.%NiCr$. As the heating temperature was increased, the hardness of heating layer was increased because of the fine microstructure and the decrease of porosity. The adhesion strength was decreased for coarsening and connection of voids in the insulation layer, and the electrical resistivity of heating layer was increased for fine crack formation and growth. In this study, the best efficient sprayed coatings with heating unit was concluded as the plasma sprayed $TiO_2-10wt.%NiCr$ coatings that was heat treated at $300^{\circ}C$.

• 한국산학기술학회논문지
• /
• 제19권1호
• /
• pp.105-112
• /
• 2018

본 논문은 로이유리(Low emissivity glass) 표면에 증착되어 있는 금속박막의 전도 특성을 이용하여 발열유리(Heatable glass)를 제작하는 방법에 대해 제안한다. 로이유리의 발열량은 로이유리 표면저항에 의한 주울(Joule) 열에 의존하므로 소재의 표면저항을 측정함으로써 예측 및 설계가 가능하다. 본 연구에서는 저방사층이 11nm인 소프트로이유리 시료에 각 50mm 간격으로 은(Ag) 전극을 형성시키고, 4단자법으로 면저항을 측정하여 로이유리의 소비전력과 발열량을 예측한 후에, 제작 및 실험을 통해 발열성능을 확인하였다. 기존의 발열유리 제작방법은 크게 두 가지로 일반유리(Normal glass)에 니크롬(Nichrome) 열선을 삽입하는 방법과, 일반유리에 전도성 투명박막을 증착하는 방법이 있다. 니크롬 열선 삽입 방식은 발열성능은 우수하나 유리 고유의 투명성을 저해하고, 전도성 투명박막을 증착하는 방법은 투명성은 양호하나 공정이 복잡하여 실용성이 저하된다. 본 논문에서는 주로 건축물의 단열효과 향상을 위해 사용되는 로이유리를 이용하여 로이유리 전면에 코팅되어 있는 전도성 금속박막에 레이저 빔을 조사하여 원하는 발열성능을 가지는 발열유리를 제작하는 방법을 제안한다. 제안된 방법은 기존의 니크롬 열선을 삽입하는 방법에 비해 투명성이 양호하고, 전도성 투명박막을 증착하는 방법에 비해 제작과정이 보다 수월함을 확인하였다. 아울러, 레이저를 조사하여 로이유리의 표면 박막을 패터닝(Patterning) 하는 형태에 따른 발열특성의 비교와 로이유리에 적합한 레이저 출력조건을 제시하고자 한다.

• 한국표면공학회지
• /
• 제47권1호
• /
• pp.20-24
• /
• 2014

Joule heat is generated by applying an electric filed to a conductive layer located beneath or above the amorphous silicon film, and is used to raise the temperature of the silicon film to crystallization temperature. An electric field was applied to an indium tin oxide (ITO) conductive layer to induce Joule heating in order to carry out the crystallization of amorphous silicon. Polycrystalline silicon was produced within the range of a millisecond. To investigate the kinetics of Joule-heating induced crystallization (JIC) solid phase crystallization was conducted using amorphous silicon films deposited by plasma enhanced chemical vapor deposition and using tube furnace in nitrogen ambient. Microscopic and macroscopic uniformity of crystallinity of JIC poly-Si was measured to have better uniformity compared to that of poly-Si produced by other methods such as metal induced crystallization and Excimer laser crystallization.