• Design & Manufacturing
• /
• 제16권2호
• /
• pp.46-52
• /
• 2022

As the consumer market in the eco-friendly vehicle industry grows, the demand for water pump in a electric car parts market. This study intend to propose a mathematical model that can verify the effect of improving thermal properties when a non-conductive cooling filler liquid is introduced into an electric vehicle water pump. Also, the pros and cons of the immersion cooling method and future development way were suggested by analyzing the cooling characteristics using on the derived analysis solution. Thermal characteristics analysis of electric water pump applied with non-conductive filler liquid was carried out, and the diffusion boundary condition in the motor body and the boundary condition the inside pump were expressed as a geometric model. As a result of analyzing the temperature change for the heat source of the natural convection method and the heat conduction method, the natural convection method has difficulty in dissipating heat because no decrease in temperature due to heat release was found even after 300 sec. Also, it can be seen that the heat dissipation effect was obtained even though the non-conductive filling liquid was applied at the 120 sec and 180 sec in the heat conduction method. It has proposed to minimize thermal embrittlement and lower motor torque by injecting a non-conductive filler liquid into the motor body and designing a partition wall thickness of 2.5 mm or less.

• 한국전기전자재료학회논문지
• /
• 제16권11호
• /
• pp.1008-1013
• /
• 2003

We have studied the effect of black matrix (BM) according to the dielectric anisotropy of liquid crystals (LCs) for a homogeneously aligned LC cell driven by fringe-electric field. The results show that for a LC with positive dielectric anisotropy (+LC) there is a large transmittance change when using a conductive BM, whereas the transmittance change is low for a LC with negative dielectric anisotropy (-LC). The conductive BM existing on top substrate produces vertical electric field, which makes the LC molecules be tilt upward from the substrate and have small twist angle for the +LC. However, for the -LC the conductive BM affects the LC distribution only slightly due to characteristic of the -LC orienting perpendicular to the field. Therefore, for the +LC the electro-optic characteristics are strongly dependent on conductivity of the BM on top substrate in a homogeneous liquid crystal cell driven by fringe-electric field.

• ETRI Journal
• /
• 제41권6호
• /
• pp.820-828
• /
• 2019

A highly reliable conductive adhesive obtained by transient liquid-phase sintering (TLPS) technologies is studied for use in high-power device packaging. TLPS involves the low-temperature reaction of a low-melting metal or alloy with a high-melting metal or alloy to form a reacted metal matrix. For a TLPS material (consisting of Ag-coated Cu, a Sn96.5-Ag3.0-Cu0.5 solder, and a volatile fluxing resin) used herein, the melting temperature of the metal matrix exceeds the bonding temperature. After bonding of the TLPS material, a unique melting peak of TLPS is observed at 356 ℃, consistent with the transient behavior of Ag₃Sn + Cu₆Sn₅ → liquid + Cu₃Sn reported by the National Institute of Standards and Technology. The TLPS material shows superior thermal conductivity as compared with other commercially available Ag pastes under the same specimen preparation conditions. In conclusion, the TLPS material can be a promising candidate for a highly reliable conductive adhesive in power device packaging because remelting of the SAC305 solder, which is widely used in conventional power modules, is not observed.

• 대한의용생체공학회:의공학회지
• /
• 제40권5호
• /
• pp.151-157
• /
• 2019

An acoustofluidic device using conductive liquid-based electrodes was developed for malaria parasite separation from white blood cells. In this device, the electrode channels filled with a conductive liquid were used to generate standing surface acoustic waves (SSAWs) in a fluidic channel, which can overcome the limitation of conventional patterned metal electrodes. Separation performance of the device was evaluated using fluorescent polystyrene particles with two different sizes (2 and $10{\mu}m$ diameters), which were successfully separated. In addition, a mixture of malaria parasites and white blood cells were also efficiently separated with high purity of ~98% in the CL-SSAW device at the flow rate of $12{\mu}l/min$.

• 비파괴검사학회지
• /
• 제35권6호
• /
• pp.414-420
• /
• 2015

Concrete undergoes significant phase changes from liquid to solid states as hydration progresses. These phase changes are known as the setting process. A liquid state concrete is electrically conductive because of the presence of water and ions. However, since the conductive elements in the liquid state of concrete are consumed to produce non-conductive hydration products, the electrical conductivity of hydrating concrete decreases during the setting process. Therefore, the electrical properties of hydrating concrete can be used to monitor the setting process of concrete. In this study, a parameter identification method to estimate electrical parameters such as ohmic resistance of concrete is proposed. The effectiveness of the proposed method for monitoring the setting process of concrete is experimentally validated.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2014년도 제46회 동계 정기학술대회 초록집
• /
• pp.241.2-241.2
• /
• 2014

We present highly transparent liquid crystal displays (LCDs) using hybrid films based on carbon nanomaterials, metal grid, and indium-tin-oxide (ITO) grid. Carbon based nanomaterials are used as transparent electrodes because of high transmittance. Despite of their high transmittance they have relatively high sheet resistance. To solve this problem, we applied grid and made hybrid conductive films based on carbon nanomaterials. Conventional photolithography processes were used to make a grid pattern of metal and ITO. To fabricate transparent conductive films, carbon nanotube (CNT) ink was spin coated on the grid pattern. The transparency of the conductive film was controlled by shape and size of the grid pattern and the thickness of CNT films. The optical transmittance of CNT-based hybrid films is 92.2% and sheet resistance is also reduced to $168{\Omega}/square$. These substrates were used for the fabrication of typical twisted nematic (TN) LCD cells. From the characteristics of LCD devices such as transmittance, operating voltage, voltage holding ratio our devices were comparable to those of pristine ITO substrates. The result shows that the hybrid conductive films based on carbon nanomaterials could be alternative of ITO for the highly transparent LCDs.

• 한국진공학회지
• /
• 제20권2호
• /
• pp.146-154
• /
• 2011

접착테이프 형태의 액체누설 감지 필름 센서와 이를 이용하고 경보 장치를 포함한 감지 시스템을 개발하였다. 액체누설 감지 필름형 테이프 센서는 베이스 필름층, 전도성 라인층, 보호 필름층으로 구성되며, 테이프의 두께 $300{\sim}500{\mu}m$, 폭 3.55 cm, 그리고 단위 테이프의 길이는 200 m이다. 전도성 라인층의 필름에는 3개의 전도선과 1개의 저항선이 있다. 이들은 도전성 은나노 잉크를 전자인쇄방식으로 설치한다. 이들 저항선과 전도선 사이에 액체가 누설되어 전기적으로 상호 통전되면, 두 선사이의 저항변화를 전압의 변화로 계측하여 누설 위치를 감지한다. 물을 포함한 전도성 액체에 대한 누설 위치 감지에서 길이 200 m에서 오차 범위는 ${\pm}1m$ 이내이다.

• 한국표면공학회지
• /
• 제41권1호
• /
• pp.6-11
• /
• 2008

An Indium Zinc Oxide(IZO) transparent conductive layer was deposited on a large size glass substrate by using magnetron dc sputtering method with varying a deposition temperature. As the deposition temperature decreased to a room temperature, the sheet resistance of IZO film increased. But this deposition temperature range is included in an applicable to a device. From a standpoint of the sheet resistance, the differences of the sheet resistance were not great and the uniformity of the layer was uniformed around 10%. Crystallization particles were shown on the surface of the layer as deposition temperature increased, but these particles were not shown on the surface of the layer as deposition temperature decreased to the room temperature. It didn't make a scrap of difference in a transmittance of varying deposition temperature. Therefore, it is concluded that IZO thin film manufactured by the room temperature deposition condition can be used as a large size transparent conductive layer of a liquid crystal display device.

• 조명전기설비학회논문지
• /
• 제25권8호
• /
• pp.39-47
• /
• 2011

The motion of a conductive spherical particle under uniform electric field is investigated in order to find a suitable method for removing the conducting solid impurities contained in liquid plastic. When the positive dc voltage applied to the upper electrode, the vertical up-and-down motion of a charged particle by electrostatic force is observed by a charge-coupled device (CCD) camera or a high-speed video camera. The experimental data of the static threshold voltage by which the particle starts to move toward the counter electrode in air or silicone oil are in good agreement with theoretical value. When the applied voltage is larger than the static threshold voltage, the particle motion pattern in silicone oil consists of four stages: upward motion, stopping at the upper electrode, downward motion and stopping at the lower electrode. The stopping motion on the electrode is thought to be caused by the liquid flow accompanied by the particle motion. The particle charge calculated by integrating the pulse current, which is generated by the charge exchange between the electrode and the particle, is approximately 0.1~0.25 times of the theoretical value. This study is expected to help understand the electric properties of microparticles in oil circuit breaker (OCB) and oil transformer and improve their performance and longevity.

• 마이크로전자및패키징학회지
• /
• 제27권3호
• /
• pp.49-54
• /
• 2020

신축/유연한 전극을 무언가에 접착하거나 전극에 무언가를 접착하기 위해서는 전극의 특성에 맞는 전도성 접착제가 필요하다. 전도성 접착제는 접착성과 전도성이 필수적으로 요구된다. 특히 접착성 부분은 내구성과 내열성이 요구되며 기존 접착제와 다르게 전도성까지 보유해야한다. 그러기 위해서는 강도와 접착성이 좋은 에폭시를 접착제로 선정하였고 여기에 기존 주제와 경화제로 이루어진 2액형 소재가 아닌 가소제와 보강제까지 혼합하여 4액형 소재를 사용하여 신축/유연성을 고분자에 부여하였다. 전도성 필러는 비저항이 낮은 재료인 은으로 선정하였고 높은 전도성을 위해 3가지 모양의 Ag 입자를 사용해 패킹성을 높였다. 이렇게 개발된 전도성 접착제와 실제 판매되고 있는 에폭시 기반 전도성 접착제 2개와 전도성을 비교하였고 실제 판매되고 있는 제품보다 약 10배정도의 우수한 전도성 결과가 도출되었다. 그리고 가소제와 보강제 여부에 따른 전도성, 기계적 특성, 접착력, 강도를 평가하였다. 또한 120℃에서 5분 경화 후에 60%의 인장에도 문제가 없었으며 연필경도는 6H로 우수하게 측정되었다. 3M tape test를 통해 전극의 접착력을 확인한 결과 바인더의 배합 비율에 관계없이 모두 우수한 결과를 보였다. 전극 위에 Cu sheet를 전도성 접착제를 통해 부착시킨 후 접촉저항을 확인한 결과 0.3 Ω으로 우수한 성능을 보였다.