• Proceedings of the KIEE Conference
• /
• 2003.04a
• /
• pp.82-84
• /
• 2003

In case contact between point of contacts is not achieved well, contact resistance is grown, and by current concentration at current conducting contacts can weld. In order to decrease contact resistance between contacts in case of busbar, installing spring between fixed contact and moving contact. and then force on faying surface of contacts increase and contact resistance decrease. But, in case increase force of spring to widen contact area, operating force moving contact can grow, on the contrary force of spring is small, contact resistance becomes low. Therefore, need to optimize force and number of spring. position, and also need to examine force change on contact surface at point of contact moving. In this paper, dynamic kinetics analysis for force on faying surface of contacts is performed at unsteady state. It is showed to not uniform force on surface between contacts, and we can got more uniform force by means of change spring position.

• Nuclear Engineering and Technology
• /
• v.43 no.5
• /
• pp.447-458
• /
• 2011

This paper proposes an approximated contact force model to identify the nonlinear behavior of a fuel rod with gap supports; also, the numerical prediction of interfacial forces in the mechanical contact of fuel rods with gap supports is studied. The Newmark integration method requires the current status of the contact force, but the contact force is not given a priori. Taylor's expansion can be used to predict the unknown contact force; therefore, it should be guaranteed that the first derivative of the contact force is continuous. This work proposes a continuous and differentiable contact force model with the ability to estimate the current state of the contact force. An approximated convex and differentiable potential function for the contact force is described, and a variational formulation is also provided. A numerical example that considers the particularly stiff supports has been studied, and a fuel rod with hardening supports was also examined for a realistic simulation. An approximated proper solution can be obtained using the results, and abrupt changes from the contacting state to non-contacting state, or vice versa, can be relieved. It can also be seen that not only the external force but also the developed contact force affects the response.

• Proceedings of the KSME Conference
• /
• 2003.11a
• /
• pp.1453-1457
• /
• 2003

The pantograph for Korean High Speed Train was developed by home-grown technology. In this study, a system to measure the contact force of pantograph is developed and installed on the prototype high speed train, Contact force prevents the pantograph from separating from the catenary. However, excessive contact force causes rapid erosion of catenary. The contact force can be divided into lift force and spring force. Contact force measurement is conducted while the train runs on the test track. The lift force is measured by the load cell on the roof separately and combined with the spring force of pan-head to form the contact force. Measured results show that the contact force of the pantograph of Korean High Speed Train is below the upper limit regulated by the high speed train standards. The contact force measuring system provides data to evaluate safety of the catenary system.

• The Journal of Korea Robotics Society
• /
• v.18 no.4
• /
• pp.481-486
• /
• 2023

The purpose of this study is to optimize parameters of a contact model to obtain similar ground contact force of human walking. Dynamic walking simulation considering ground contact is performed to determine load specifications when developing walking assist robots. Large contact forces that are not observed in actual experimental data occur during the simulation at the initial contact (e.g., heel contact). The large contact force generates unrealistic large joint torques. A lower exoskeleton robot with no ankles is developed with the Matlab simscape and the nonlinear hyper volumetric contact model is applied. Parameters of the nonlinear hyper volumetric model were optimized using actual walking contact force data. As a result of optimization, it was possible to obtain a contact force pattern similar to actual walking by removing the large contact force generated during initial contact.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2001.05a
• /
• pp.780-785
• /
• 2001

A method for accurate measurement of the contact force in the current collection system of the high-speed railway is developed. In order to measure the contact force with minimal modifications to the pantograph, strain gauges are attached to the bottom of the contact strip. An algorithm for deriving the magnitude and stagger of the contact force from the bending strain measurements is devised. For the sample pantograph, the static contact forces are measured to within ${\pm}$5 % error for the magnitude and ${\pm}$ 2cm error for the stagger. For dynamic contact force measurement, it is found that the contact strip can the regarded as a rigid body for the contact frequency of less than 15 ㎐.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.10 no.4
• /
• pp.123-129
• /
• 2001

Recent requirements for the fast and accurate motion in industrial robot manipulators need more advanced control tech-niques. To satisfy the requirements, importance of force control is being continuously increased and the expensive force sensor is usually installed to obtain the contact force information in practice. This information is indispensable for the force control of maintaining the desired contact force. However, the sensor cost is too high to be used in industrial applications. In this paper, it is proposed to estimated the contact force occurring between the end-effector of 2 DOF robots and environ-ment. The contact force estimation system is developed based on the static and dynamic models of 2 DOF robot manipula-tors. where the contact force is described with respect to the link torque. The Extended Kalman Filter is designed and its performance is verified in simulations.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2000.10a
• /
• pp.14-19
• /
• 2000

Recent requirements for the fast and accurate motion in industrial robot manipulator need more advanced control techniques. To satisfy the requirements, importance of the force control is being continuously increased and the expensive force sensor is usually installed to obtain the contact force information in practice. This information is indispensable for the force control of maintaining the desired contact force. However the sensor cost is too high to be used in industrial applications. In this paper, it is proposed to estimate the contact force occurred between the end-effector of 2 DOF robots and environment. The contact force estimation system is developed based on the static and dynamic models of 2 DOF robot manipulators, where the contact force is described with respect to the link torque. The Extended Kalman Filter is designed and its performance is verified in simulations.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.25 no.2
• /
• pp.192-197
• /
• 2001

Recent requirements for the fast and accurate motion in industrial robot manipulators need more advanced control techniques. To satisfy the requirements, importance of the force control is being continuously increased and the expensive force sensor is often installed to obtain the contact force information in practice. This information is indispensable for the force control of maintaining the desired contact force. However, the sensor cost is too high to be used in industrial applications. In this paper, it is proposed to estimate the contact force occurred between the end-effector of robots and environment in 3-D. The contact force monitoring system is developed based on the static and dynamic models of 3 DOF robot manipulators, where the contact force is described with respect to the link torque. The Extended Kalman Filter is designed and its performance is verified in simulations.

• Journal of the Korean Society for Precision Engineering
• /
• v.27 no.1
• /
• pp.58-63
• /
• 2010

A new contact force estimation technique is proposed. Keeping the contact force at a certain level between finishing tool and the object is essential since the quality of the finished surface is very sensitive to the contact force during the finishing process. However, the contact force measurement cannot be obtained by simply installing load cells under machine table or in the middle of tool linkage. The reason is that the weight of the machine table and the tool linkage are much heavier than the force to be measured. To that end, a method for estimating disturbance is proposed for a system that is similar to the mechanism of the finishing machine, and the same method is applied to estimate the contact force of the brush-type finishing machine. To verify the effectiveness of the proposed method, a small scale test set-up has been built and the method has been tested.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.24 no.2 s.173
• /
• pp.411-420
• /
• 2000

This paper presents a new method for calculating contact position and contact force. The proposed method calculates accurate contact position by introducing intermediate parameters. Accurate contac t force can be obtained by solving reduced equations of motion iteratively. This method can be applied to calculate not only contact force on contact points but also contact force on kinematic joints such as a rotational joint and a translational joint. Four numerical examples are given to demonstrate the effectiveness of the proposed algorithm.