• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2018.10a
• /
• pp.577-578
• /
• 2018

In this paper, we evaluate the throughput performance of IEEE 802.15.4 Time Slotted Channel Hopping (TSCH) tree network using Contiki-NG operating system. We build a virtual simulation environment to compare the throughput performance of various IEEE 802.15.4 TSCH networks according to the changes in the number of nodes and the hop counts. The simulation results show that the throughput increases as the number of nodes increase while it decreases as the hop counts increase.

• Journal of Multimedia Information System
• /
• v.5 no.1
• /
• pp.27-34
• /
• 2018

In recent years, with the blooming of Internet of Things (IoT) and Cloud Computing (CC), researchers have begun to discover new methods of technological support in all areas (e.g. health, transport, education, etc.). In this paper, in order to achieve a type of network that will provide more intelligent media-data transfer new technologies were studied. Additionally, we have been studied the use of various open source tools, such as CC analyzers and simulators. These tools are useful for studying the collection, the storage, the management, the processing, and the analysis of large volumes of data. The simulation platform which have been used for our research is CloudSim, which runs on Eclipse software. Thus, after measuring the network performance with CloudSim, we also use the Cooja emulator of the Contiki OS, with the aim to confirm and access more metrics and options. More specifically, we have implemented a network topology from a small section of the script of CloudSim with Cooja, so that we can test a single network segment. The results of our experimental procedure show that there are not duplicated packets received during the procedure. This research could be a start point for better and more efficient media data transmission.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.38B no.9
• /
• pp.687-699
• /
• 2013

IP-based IP-USN overcomes that disadvantages of verify the existence and geographic limits of the sensor by applying a standard technique called 6LoWPAN. However, in terms of the management and cost, The USN node should work for a long period of time without periodic batter replacement. but this solution is insufficient.In this paper, we configure the node using TI's CC2530 that low-power Soc solution and Contiki OS for optimal low-power operation IP-USN and implement the gateway to support connecting IP networks and Sensor networks. In addition, a system implemented to measure and analyze the energy consumption of an independent power supply to look for ways.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.24 no.11
• /
• pp.1477-1483
• /
• 2020

The stability guarantee of wireless network based control systems is still challenging due to the lossy links and node failures. This paper proposes a hierarchical cluster-based network protocol called robust wireless sensor and actuator network (R-WSAN) by combining time, channel, and space resource diversity. R-WSAN includes a scheduling algorithm to support the network resource allocation and a control task sharing scheme to maintain the control stability of multiple plants. R-WSAN was implemented on a real test-bed using Zolertia RE-Mote embedded hardware platform running the Contiki-NG operating system. Our experimental results demonstrate that R-WSAN provides highly reliable and robust performance against lossy links and node failures. Furthermore, the proposed scheduling algorithm and the task sharing scheme meet the stability requirement of control systems, even if the controller fails to support the control task.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.23 no.12
• /
• pp.1679-1686
• /
• 2019

The main purpose of this research is to propose an approach for solving the packet loss problem by quickly adapting to topology change when nodes move in RPL-based IoT environment. In order to enhance mobility, every node is aware of the mobility of its neighbor nodes and quantifies the mobility level based on the number of control messages and all received packets. According to the mobility level, the DIO timer is changed. The proposed approach allows nodes to change their DIO timers according to their mobility levels to adapt topology changes and update paths to the sink. The performance of the proposed approach is evaluated using a Contiki-based Cooja simulator in various moving speeds. The simulation results show that the proposed approach copes with mobility scenarios better than the standard RPL by ascertaining that the packet delivery ratio is improved by 31.03%.

• IEMEK Journal of Embedded Systems and Applications
• /
• v.18 no.4
• /
• pp.151-157
• /
• 2023

RPL (IPv6 Routing Protocol for Low-power Lossy Network) is a standardized routing protocol for LLNs (Low power and Lossy Networks) by the IETF (Internet Engineering Task Force). RPL creates routes and builds a DODAG (Destination Oriented Directed Acyclic Graph) through OF (Objective Function) defining routing metrics and optimization objectives. RPL supports a leaf mode which does not allow any child nodes. In this paper, we propose INFRA-RPL which provides a dynamic leaf mode functionality to a leaf node with the mobility. The proposed protocol is implemented in the open-source IoT operating system, Contiki-NG and Cooja simulator, and its performance is evaluated. The evaluation results show that INFRA-RPL outperforms the existing protocols in the terms of PDR, latency, and control message overhead.

• Journal of Korea Society of Industrial Information Systems
• /
• v.27 no.6
• /
• pp.41-49
• /
• 2022

The Internet Engineering Task Force (IETF) has standardized RPL (IPv6 Routing Protocol for Low-power Lossy Network) as a routing protocol for Low Power and Lossy Networks (LLNs), a low power loss network environment. RPL creates a route through an Objective Function (OF) suitable for the service required by LLNs and builds a Destination Oriented Directed Acyclic Graph (DODAG). Existing studies check the residual energy of each node and select a parent with the highest residual energy to build a DODAG, but the energy exhaustion of the parent can not avoid the network disconnection of the children nodes. Therefore, this paper proposes EC-RPL (Enhanced Connectivity-RPL), in which ta node leaves DODAG in advance when the remaining energy of the node falls below the specified energy threshold. The proposed protocol is implemented in Contiki, an open-source IoT operating system, and its performance is evaluated in Cooja simulator, and the number of control messages is compared using Foren6. Experimental results show that EC-RPL has 6.9% lower latency and 5.8% fewer control messages than the existing RPL, and the packet delivery rate is 1.7% higher.

• Journal of Korea Multimedia Society
• /
• v.12 no.3
• /
• pp.436-444
• /
• 2009

As the interest in sensor networks has been increased recently, researches have been performed in many areas using sensor networks. In this paper, we propose and implement a lecture room control system based on a sensor network. It is possible to give an efficient lecture by collecting lecturers' lecture history information through the sensor network and controlling a PC, a beam projector, lights, etc. in a lecture room appropriately using the information. We construct a sensor network and perform experiments so that the proposed lecture room control system performs efficiently. Through the experiments, we obtained the optimal message generation period of the sensor node in a lecture room and the optimal number of sensor nodes deployed in a lecture room to communicate without any trouble between sensor nodes.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.11 no.2
• /
• pp.1070-1088
• /
• 2017

Recently, the applications of Internet of Things (IoTs) are growing rapidly. Wireless Sensor Network (WSN) becomes an emerging technology to provide the low power wireless connectivity for IoTs. The IPv6 over low-power wireless personal area networks (6LoWPAN) has been proposed by IETF, which gives each WSN device an IPv6 address to connect with the Internet. The transmission congestion in IoTs could be a problem when a large numbers of sensors are deployed in the field. Therefore, it is important to consider whether the WSN devices have be completely integrated into the Internet with proper quality of service (QoS) requirements. The Software Defined Network (SDN) is a new architecture of network decoupling the data and control planes, and using the logical centralized control to manage the forwarding issues in large-scale networks. In this research, the SDN-based 6LoWPAN Border Router (6LBR) is proposed to integrate the transmission from WSNs to Internet. The proposed SDN-based 6LBR communicating between WSNs and the Internet will bring forward the requirements of end-to-end QoS with bandwidth guarantee. Based on our experimental results, we have observed that the selected 6LoWPAN traffic flows achieve lower packet loss rate in the Internet. Therefore, the 6LoWPAN traffic flows classified by SDN-based 6LBR can be reserved for the required bandwidth in the Internet to meet the QoS requirements.

• Journal of Communications and Networks
• /
• v.18 no.3
• /
• pp.327-332
• /
• 2016

The routing protocol for low-power and lossy networks (RPL) is an internet protocol based routing protocol developed and standardized by IETF in 2012 to support a wide range of applications for low-power and lossy-networks (LLNs). In LLNs consisting of resource-constrained devices, the energy consumption of battery powered sensing devices during network operations can greatly impact network lifetime. In the case of inefficient route selection, the energy depletion from even a few nodes in the network can damage network integrity and reliability by creating holes in the network. In this paper, a composite energy-aware node metric ($RER_{BDI}$) is proposed for RPL; this metric uses both the residual energy ratio (RER) of the nodes and their battery discharge index. This composite metric helps avoid overburdening power depleted network nodes during packet routing from the source towards the destination oriented directed acyclic graph root node. Additionally, an objective function is defined for RPL, which combines the node metric $RER_{BDI}$ and the expected transmission count (ETX) link quality metric; this helps to improve the overall network packet delivery ratio. The COOJA simulator is used to evaluate the performance of the proposed scheme. The simulations show encouraging results for the proposed scheme in terms of network lifetime, packet delivery ratio and energy consumption, when compared to the most popular schemes for RPL like ETX, hop-count and RER.