• Journal of the Institute of Convergence Signal Processing
• /
• v.10 no.2
• /
• pp.146-150
• /
• 2009

An Intelligent active roll angle controller design algorithm is discussed. The detailed mathematical formulation and analysis are discussed, and then modeling and design method for active roll angle controller are presented. This paper proposes a design method based upon intelligent robust controller design algorithm to control actively roll angle for improving cornering performance problems. The intelligent robust controller is designed for steady speed driving vehicle system model with representation of steering angle and yaw angular velocity parameters for cornering stability. And the detailed formulation and analysis for the objective vehicle system are investigated.

• Journal of the Institute of Convergence Signal Processing
• /
• v.3 no.1
• /
• pp.61-66
• /
• 2002

A fuzzy control strategy is described which is utilized to control the joint angle and tip deflection in single flexible manipulator. In this paper, an existing model for a single flexible manipulator is used for the initial development of an FLC. One FLC is designed to govern the joint angle of the manipulator as it is rotated from one position to another, and the second FLC is designed to attenuate the tip deflection which result from joint angle body motion. Reference Trajectory Command is an important method to reduce vibration in flexible beam. This paper presents a very simple command control shaping which eliminates multiple mode residual vibration in a flexible beam combined parallel fuzzy controller. The effectiveness of proposed scheme is demonstrated through computer simulation.

• ETRI Journal
• /
• v.37 no.3
• /
• pp.617-625
• /
• 2015

In this paper, a steering control system for the path tracking of autonomous vehicles is described. The steering control system consists of a path tracker and primitive driver. The path tracker generates the desired steering angle by using the look-ahead distance, vehicle heading, and a lateral offset. A method for applying an autonomous vehicle to path tracking is an advanced pure pursuit method that can reduce cutting corners, which is a weakness of the pure pursuit method. The steering controller controls the steering actuator to follow the desired steering angle. A servo motor is installed to control the steering handle, and it can transmit the steering force using a belt and pulley. We designed a steering controller that is applied to a proportional integral differential controller. However, because of a dead band, the path tracking performance and stability of autonomous vehicles are reduced. To overcome the dead band, a dead band compensator was developed. As a result of the compensator, the path tracking performance and stability are improved.

• Korean Journal of Applied Biomechanics
• /
• v.31 no.2
• /
• pp.119-125
• /
• 2021

Objective: The purpose of this study was to identify the effect of dynamic postural balance control against tilting platform between golfers and non-golfers. Method: 24 golfers and 26 non-golfers were participated. Eight motion capture cameras, two force plates, and one dynamic balance control platform were used for sensory perception test. It was performed two-way repeated ANOVA with a Bonferroni adjustment at a significant level of a 0.05. Results: Golfers' perception ability was higher than non-golfer according to slope. the CoP, time, angle variables were indicated main effect and interaction effect between golfer and non-golfer. Conclusion: It was known that golfer's proprioception perception ability was higher than non-golfers. Repeated practice such as shots and putting on the uneven ground might improve their balance control.

• Journal of the Institute of Convergence Signal Processing
• /
• v.22 no.4
• /
• pp.171-178
• /
• 2021

Caravans are easily affected by external physical factors and often cause dangerous situations for passengers. Therefore, in order to secure the stability of the passenger, there is a need to develop a sway reduction device capable of preventing the sway phenomenon in advance. This paper aims to minimize the hitch angle between the tow vehicle and the caravan. Specifically, the initial instability of the caravan is detected through an IMU sensor mounted on each of the tow vehicle and the caravan, and a control value is calculated to reduce errors from the Hitch angle and Hitch yaw rate using a PID controller. Different braking torques are generated, distributed, and controlled on the left and right brakes of the caravan according to the calculated control value. It could be verified through the driving experiment that the hitch angle was decreased compared to the case where the performance of the sway reduction device was not controlled, and the transverse stability improvement rate was improved by 94.49% compared to before control.

• 제어로봇시스템학회:학술대회논문집
• /
• 1992.10a
• /
• pp.159-164
• /
• 1992

In this paper, the complex nonlinear dynamics of a satellite is obtained. And it is shown that several limitations exist when the magnetorquer is used as an active actuator to attitude control. Such limitations cause a delayed convergence of pitch and roll angle. The simulation results insure that the roll angle bias is dependent on the z axis spin rate. And a heuristic algorithm is applied to control the attitude libration through the computer simulations.

• Proceedings of the Optical Society of Korea Conference
• /
• 2007.02a
• /
• pp.247-248
• /
• 2007

Control convergence of Horizontal-Moving stereoscopic camera is demonstrated with object distance. To acquire object distance calculated vergence angle is needed. Compare calculated vergence angle with look up table, processing time of auto control is reduce.

• Journal of the Korean Society of Industry Convergence
• /
• v.19 no.2
• /
• pp.81-87
• /
• 2016

This paper presents a new approach to control of stable motion of single wheel driving robot system of a pitch that is controlled by an in-wheel motor and a roll that is controlled by a reaction wheel. This robot doesn'thave any actuator for a yaw axis control, which makes the derivation of the dynamics relatively simple. The Lagrange equations was applied to derive the dynamic equations of the one wheel driving robot to implement the dynamic speed control of the mobile robot. To achieve the real time speed control of the unicycle robot, the sliding mode control and optical regulator are utilized to prove the reliability while maintaining the desired speed tracking performance. In the roll controller, the sigmoid-function based robust controller has been adopted to reduce the vibration by the situation function. The optimal controller has been implemented for the pitch control to drive the unicycle robot to follow the desired velocity trajectory in real time using the state variables of pitch angle, angular velocity, angle and angular velocity of the driving wheel. The control performance of the control systems from a single dynamic model has been illustrated by the real experiments.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.47 no.7
• /
• pp.508-516
• /
• 2019

In this paper, we propose a guidance law to control Impact Angle in consideration of look angle limit of the missile with strapdown seeker on the non-maneuvering target. The proposed law is based on sliding mode algorithm and generates acceleration commands using look angle and line of sight information provided by the strapdown seeker and navigation system. And, target velocity and target path angle are provided by like TADS (Target Acquisition and Designation System) at launch time. We can confirm that the target interception and impact angle control are possible through the convergence of the proposed sliding surface. In addition, it is possible to confirm that the sign of derivative result of the look angle at the maximum and minimum look angle is opposite to the sign of the look angle, so the look angle limit is not exceeded.

• Journal of the Korean Society of Industry Convergence
• /
• v.20 no.4
• /
• pp.299-305
• /
• 2017

This study proposes a new technique to design and control of robot hand gripper for assembling and disassembling of a machine parts. The motion equation describing dynamics of the manipulators and object together with geometric constraint is formulated by Lagrange-Euler's equation. And the problems of controlling both the grasping force and the rotation angle of the grasped object under the constraints are analyzed. The effect of geometric constraints and a method of computer simulation for overall system is verified. Finally, it is illustrated that even in case of there exists a sensory feedback from sensing data of the rotational angle of the object to command inputs control of joint and this feedback connection from sensing data to control grasping of machinery parts.