• Journal of information and communication convergence engineering
• /
• 제1권3호
• /
• pp.139-142
• /
• 2003

In this paper, we consider the factors that affect a conversion loss performance in designing a single balanced diode mixer integrated with IRF(Image Reject Filter), based on the embedded electrical wavelength placed between the IRF and mixer, diode matching and LO drive amplifier. To evaluate the conversion loss performance, we suggest two types of a single balanced mixer using 90 degree branch line coupler, microstrip line and schottky diode. One is only mixer and the other is integrated with IRF and LO drive amplifier. The measured results of a single balance diode mixer integrated IRF show the conversion loss of 8.5 dB and the flatness of 1 dB p-p from 21.2 GHz to 22.6 GHz with 10 dBm LO. The measured input PI dB and IIP3 are 7 dBm and 15 dBm respectively under the nominal LO power level of 10dBm. The LO/RF and LO/IF isolation are 22 dB and 50 dB, respectively.

• 한국통신학회논문지
• /
• 제38A권9호
• /
• pp.792-797
• /
• 2013

본 논문에서는 강한 광대역정규잡음 환경에서 송신한 확산신호와 수신기에서 발생한 확산신호의 동기에 따른 2비트 비균등 양자화기의 변환손실을 (conversion loss) 분석하고, 이를 통해 변환손실이 최소인 2비트 비균등 양자화기의 출력은 ${\pm}1$, ${\pm}2$이고, 양자화 간격은 재밍 대 신호 전력비로 근사화할 수 있음을 보인다.

• 전기학회논문지
• /
• 제65권3호
• /
• pp.520-525
• /
• 2016

In this paper, Characteristic of power conversion unit of a railway vehicles according to contact loss in feeding system that applied impedance of rigid conductor is analyzed. It applied impedance of rigid bar in modeling of electric railway system. Railway vehicles are performed of modeling based on the performance of the electric railway vehicle. Effects of the contact loss in the power conversion unit were analyzed via main transformer of railway vehicle, the input and output voltage characteristics of the converter through contact loss was generated after linking the vehicle with feeding system.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2005년도 추계종합학술대회
• /
• pp.921-924
• /
• 2005

We report low conversion loss and high LO to RF isolation 94 GHz MMIC resistive mixers based on 0.1 ${\mu}m$ InGaAs/InAlAs/GaAs metamorphic HEMT technology. The fabricated resistive mixers applied a one-stage amplifier on RF port of the mixer. By using the one-stage amplifier, we obtained the decrement of conversion loss and the increment of LO to RF isolation. So, we can obtain higher performances than conventional resistive mixers. The modified mixer shows excellent conversion loss of 6.7 dB at a LO power of 10 dBm. We also observed an extremely high isolation characteristic from the MMICs exhibiting the LO-RF isolation of 21 ${\pm}$ 0.5dB in a frequency range of 93.7${\sim}$ 94.3 GHz. The low conversion loss and high LO-RF isolation characteristics of the MMIC modified resistive mixers are mainly attributed to the performance of the MHEMTs exhibiting a maximum transconductance of 654 mS/mm, a current gain cut-off frequency of 173 GHz and a maximum oscillation frequency of 271 GHz.

• 한국태양에너지학회:학술대회논문집
• /
• 한국태양에너지학회 2011년도 추계학술발표대회 논문집
• /
• pp.45-50
• /
• 2011

The efficiency of solar cell was about 4[%] in initial stage of photovoltaic industry, but it has quite a lot of efficiency through technology advances. Today, the efficiency of c-Si solar cells is about 17 to 19[%] and the efficiency of PV modules is about 14 to 15 [%]. We called that electrical losses occurred in the Conversion of solar cells to PV modules are CTM loss(Cell To Module loss), the CTM loss typically has a value of about3~5[%]. The more efficiency of solar cell increase, differences are larger because the efficiency decrease owing to physical or technical problems occurred in the Conversion of solar cells to PV modules. In this study, the power loss factors occurred in the Conversion of solar cells to PV modules are analyzed and it is proposed that how to reduce losses of the PV module. The types of power loss factor are (1)losses of front glass and encapsulant(generally EVA sheet), (2)losses by sorting miss, (3)losses by interconnection, (4)losses by the field aging of PV modules. In further study, experimental and evaluation will be conducted to make demonstrate for proposed solutions.

• 마이크로전자및패키징학회지
• /
• 제25권3호
• /
• pp.21-30
• /
• 2018

Driven by the recent energy saving trend, conventional silicon based power conversion modules are being replaced by modules using silicon carbide. Previous papers have focused mainly on the electrical advantages of silicon carbide semiconductors that can be used to design switching devices with much lower losses than conventional silicon based devices. However, no systematic study of their thermomechanical reliability in power conversion modules using finite element method (FEM) simulation has been presented. In this paper, silicon and silicon carbide based power devices with three-phase switching were designed and compared from the viewpoint of thermomechanical reliability. The switching loss of power conversion module was measured by the switching loss evaluation system and measured switching loss data was used for the thermal FEM simulation. Temperature and stress/strain distributions were analyzed. Finally, a thermal fatigue simulation was conducted to analyze the creep phenomenon of the joining materials. It was shown that at the working frequency of 20 kHz, the maximum temperature and stress of the power conversion module with SiC chips were reduced by 56% and 47%, respectively, compared with Si chips. In addition, the creep equivalent strain of joining material in SiC chip was reduced by 53% after thermal cycle, compared with the joining material in Si chip.

• Journal of Power Electronics
• /
• 제13권1호
• /
• pp.113-121
• /
• 2013

This paper introduces a simple core loss calculation method for output filter inductor in pulse width modulation (PWM) DC-AC inverter. Amorphous C-core (AMCC-320) is used to analyze the core loss. In order to measure core loss of the output filter inductor and validate the proposed method, a single-phase half-bridge inverter and a calorimeter are used. By changing switching frequency and modulation index (MI) of the inverter, core loss of the AMCC-320 is measured with the lab-made calorimeter and the results are compared with calculated core loss. The proposed method can be easily extended to other core loss calculation of various converters.

• 전기학회논문지
• /
• 제60권7호
• /
• pp.1385-1390
• /
• 2011

A coaxial-conical-radial transmission line conversion circuits have been investigated to realize a low loss high performance microwave power divider/combiner. In order to optimize the characteristics of the device, the power divider/combiner was designed separately with two parts-the inner part and the outer part. Utilizing the rectangular approximation of the outer part, we can design the low loss device which is not affected by the partition number N of the outer part. The small return loss which is lower than 20dB was obtained on the frequency range of 5.15GHz(7.45~12.60GHz). A conical connector was employed for smooth connection between the central coaxial line and the outer radial line. Making use of the $47^{\circ}$ and $90^{\circ}$ 2-stage conical connector, the return loss lower than 30dB was obtained on the operating frequency range of 5GHz. The total return loss of the designed divider/combiner was lower than 20dB on the frequency range of 5GHz for the partition number N=11, N=12 and N=16.

• 한국수자원학회:학술대회논문집
• /
• 한국수자원학회 2008년도 학술발표회 논문집
• /
• pp.1300-1304
• /
• 2008

The fact that soil loss causing to increase muddy water and devastate an ecosystem has been appearing upon a hot social and environmental issues which should be solved. Soil losses are occurring in most agricultural areas with rainfall-induced runoff. It makes hydraulic structure unstable, causing environmental and economical problems because muddy water destroys ecosystem and causes intake water deterioration. One of three severe muddy water source areas in Soyanggang-dam watershed is Jawoon-ri region, located in Hongcheon county. In this area, many cash-crops are planted at illegally cultivated agricultural fields, which were virgin forest areas. The purpose of this study is to estimate soil loss with current land uses (including illegal cash-crop cultivation) and soil loss reduction with land use conversion from illegal cultivation back to forest. In this study, the Sediment Assessment Tool for Effective Erosion Control (SATEEC) ArcView GIS system was utilized to assess soil erosion. If the illegally cultivated agricultural areas are converted back to forest, it is expected to 17.42% reduction in soil loss. At the Jawoon-ri region, illegally cultivated agricultural areas located at over 30% and 15% slopes take 47.48 ha (30.83%) and 103.64 ha (67.29%) of illegally cultivated agricultural fields respectively. If all illegally cultivated agricultural fields are converted back to forest, it is expected that 17.41% of soil erosion and sediment reduction, 10.86% reduction with forest conversion from 30% sloping illegally agricultural fields, and 16.15% reduction with forest conversion from 15% sloping illegally agricultural fields. Therefore, illegally cultivated agricultural fields located at these sloping areas need to be first converted back to forest to maximize reductions in soil loss reduction and muddy water outflow from the Jawoon-ri regions.

• 전력전자학회논문지
• /
• 제19권1호
• /
• pp.80-90
• /
• 2014

This paper suggests loss analysis and calculation methods for efficiency improvement of power conversion equipment in detail. The detailed loss analysis and calculation has been conducted for 3.3kW On-board Battery Charger considering temperature condition. The validity of the analysis and calculation method is verified by simulation model.