• Transactions of the Korean Society of Automotive Engineers
• /
• v.6 no.1
• /
• pp.151-162
• /
• 1998

During a straight driving and cornering maneuver by a vehicle various forces and moments are exerted on the tire's footprint. A cornering properties, handling and stability performances of vehicle can be predicted by these forces and moments values. Therefore, on this study, a lateral force and a aligning torque are predicted by these forces and moments values. Therefore, on this study, a lateral force and a aligning torque are predicted using a finite element method. Contact area of the tire between bead and wheel are fixed to simplify of a finite element model. Lateral force is exerted on the rigid surface as a real load with Coulum friction after inflate and load vertically. Then, rotate the tire's axle to simulate a free rolling untill taken the equilibrium of a aligning torque. Also, experimental observations are made to test a reliability of a FE analysis conducted in this study. The finite element analysis said that good agreement was obtained with experimental results of these cornering properties, giving confidence within about one percent. So it os recommended that a finite element analysis can be used as a good tool to predicted the tire cornering properties.

• Journal of Mechanical Science and Technology
• /
• v.20 no.9
• /
• pp.1399-1409
• /
• 2006

An improved friction model was proposed with consideration of the effect of the sliding speed, the contact pressure and the temperature, and it was implemented into a user subroutine of a commercial FEM code, ABAQUS/Explicit. Then, a smooth tire was simulated for free rolling, driving, braking and cornering situations using the improved friction model and the Coulomb friction model, and the effect of the friction models on the slip, the frictional energy distribution and the cornering force and moment was analyzed. For the free rolling, the driving and the braking situations, the improved friction model and the Coulomb friction model resulted in similar profiles of the slip and the frictional energy distributions although the magnitudes were different. The slips obtained from the simulations were in a good correlation with experimental data. For the cornering situation, the Coulomb friction model with the coefficient of friction of 1 or 2 resulted in lower or higher cornering forces and moments than experimental data. In addition, in contrast to experimental data it did not result in a maximum cornering force and a decrease of the cornering moment for the increase of the speed. However, the improved friction model resulted in similar cornering forces and moments to experimental data, and it resulted in a maximum cornering force and a decrease of the cornering moment for the increase of the speed, showing a good correlation with experimental data.

• International Journal of Automotive Technology
• /
• v.7 no.4
• /
• pp.449-457
• /
• 2006

The driver model during drift cornering was examined, and a technique to improve vehicle movement performance during drift cornering was investigated. Based on the results obtained, the driver was found to steer using feedback of the body slip angle and the body slip angle velocity during drift cornering. Moreover, improvement of the cornering force characteristic, at which exceeded the maximum cornering force calm as much as possible is important.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.25 no.3
• /
• pp.399-407
• /
• 2001

The Surface, generated by end milling operation, is deteriorated by tool runout, vibration, friction, tool deflection, etc. Especially in cornering cut, surface accuracy is usually determined by varying cutting forces, which causes tool deflections. Cutting conditions like feed rate is usually kept constant during machining a part, which causes dimensional error in severe cutting. Cornering cut is a typical example of deterioration of surface accuracy when constant feed rate is applied. Therefore it becomes important to develop NC post processor module to determine optimal cutting conditions in various cutting situations. In this paper, cutting force is predicted in cornering cut with flat end mill and feed rate is determined by constraining constantly resultant force. Also some control characteristics of CNC machining center are evaluated.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.5 no.4
• /
• pp.190-198
• /
• 1997

Traction control systems are used to prevent the wheel slippage and to maximize the traction force. A new scheme of controlling the wheel slip during cornering by varying the slip ration as a function of the slip angle is proposed and dynamically simulated with the model of a front wheel driven passenger vehicle. Simulation results show that the proposed scheme is superior to conventional ones based on the fixed slip ratio during cornering and lane changes.

• Journal of the Korean Institute of Telematics and Electronics B
• /
• v.33B no.7
• /
• pp.21-31
• /
• 1996

An intelligent integrated control system is designed for the active steering and the left/right traction force distribution control of electric vehicles, where input-output linearization is employed. Also, a fuzzy-rule-based cornering force estimator is suggested to avoid using an uncertain highly nonlinear expression, and a neural network compensator is additively utilized for the estimator to correctly find cornering forece. With these techniques, the proposed control system is shown by simulation results to be robust against drastic change of the external environments such as road conditions.

• Journal of the Korean Society for Precision Engineering
• /
• v.23 no.2 s.179
• /
• pp.104-112
• /
• 2006

The influence of tire belt angle on the Plysteer Residual Aligning Torque(PRAT) and the cornering stiffness by the FEM has been studied. The PRAT is a performance factor of the tire about vehicle pull, and the cornering stiffness has relation to vehicle steering response of outdoor test. To validate FE model for analysis, simulation data for both the static stiffness(vertical, lateral) and the PRAT have been compared with the experimental data. In addition to the characteristics of the PRAT and the cornering stiffness due to the tire belt angle, rolling and cornering contact characteristics have been studied. The tendency of the PRAT and the cornering stiffness due to the belt angle can be used as a guide line for the tire design in relation to vehicle pull and vehicle steering response.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.15 no.5
• /
• pp.1572-1586
• /
• 1991

본 연구에서는 볼 엔드밀 공구를 사용한 코너가공에서 절삭력을 예측하고, 가 공중 공구의 회전주기에 대한 최대 수평합력(max. resulant force)을 일정하게 유지시 키는 모델을 개발하고, 코너가공에 적용한다. 또 금형가공에는 절삭시간을 많이 소 요하여 생산성이 떨어지게 하는 주요한 원인이 되기 때문에 최대 수평합력을 황삭가공 에 적합하도록 설정하면 본 연구의 결과로 이송속도를 결정할 수 있다.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.42 no.12
• /
• pp.997-1003
• /
• 2014

This paper describes modeling process to obtain precise landing gear model which is necessary to design a control law for ground auto-taxi, auto take-off/landing of UAV. In this paper, landing gear side force modeling is studied to complete a landing gear model of UAV. Side force modeling is performed by calculating cornering angle including steering angle. And ground directional controller is designed by using nose wheel steering and rudder steering at the same time to control course angle error. Accuracy of landing gear side force modeling and ground directional controller is proved by comparing of auto-taxi test results with simulation results.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.5 no.1
• /
• pp.110-119
• /
• 1997

Four wheel steering(4WS) systems which can control the lateral and yaw motions of vehicles by steering front and rear wheels simultaneously, have been regarded as effective for improving the stability and handing performance of vehicles. However, since the 4WS systems depend only on the lateral force of tire, they have some limitation due to the nonlinear characteristics of tire related with the saturation phenomenon of lateral force to the slip angle of tire in a near-limit-performance maneuvering range. In this study, in other to evaluate the effect of nonlinear characteristics of tire on the dynamic performance of vehicles, a new concept for driving the cornering stiffness of nonlinear tire by using the "Magic Formula" tire model is proposed. In addition, the nonlinear 4WS vehicle model is constructed based on the proposed cornering stiffness of nonlinear tire. It is noted from simulation that the nonlinear characteristics of tire affect greatly on the 4WS vehicle performance.rformance.