• Journal of the Korean Society of Marine Environment & Safety
• /
• v.21 no.2
• /
• pp.179-187
• /
• 2015

The purpose of this study is to identify the aspect that the traffic distribution function changes, according to the direction of the datum line and the horizontal and vertical positions of the datum point applied when it is calculated. Targeting routes at the entrance of Mokpo Harbor, this study tested using AIS survey data of January 2013 the effects of the three variables-direction of the datum line(${\theta}$), horizontal position($\mathfrak{L}_H$) and vertical position($\mathfrak{L}_V$) on mean ($\bar{x}$) and standard deviation (${\delta}$). The test result showed that $\bar{x}$ and ${\delta}$ were changed according to the change of ${\theta}$, because the extracted sample data were changed according to ${\theta}$; and the changes of $\bar{x}$ and ${\delta}$ according to ${\theta}$ were drawn as the relation of the sine function' sum. In addition, it was found that setting up ${\theta}$ that the change value of ${\delta}$ becomes the least as the direction of the datum line was valid, to determine the optimum passage distribution function on complex waters with multiple branches of route. The result of this study is expected to be used as basic data to understand maritime traffic flow based on more quantified data of normal distribution and make decisions related to maritime traffic safety management.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.32 no.4D
• /
• pp.407-419
• /
• 2012

It is difficult to obtain the accurate and homogeneous height information over the whole Korea due to the effect of different vertical datums have been divided into land and sea part. In this study, we tried to unify the different vertical datums using the precise spirit leveling between TBM (tidal bench mark) and BM (bench mark) in order to solve the problems caused by different vertical datums. For this, the vertical datum offsets at observed points which were calculate from leveling results and then transformation model of vertical datum will be modelled using calculated offsets along the coastal line. For suggesting the precise modelling method to vertical datum transformation, we analyzed results from various interpolation methods such as Spline and LSC method. As the results from analysis, the LSC method combined with 4-parameters trend model is more suitable for modelling the offsets between vertical datums. The final transformation model of vertical datum using the combination of LSC and 4-parameter model which provides the transformation accuracies of ${\pm}10.4cm{\sim}14.8cm$ level. And, the software for vertical datum transformation that was also developed using the final model in order to convert the height information included in various spatial data effectively. Therefore, the transformation model between vertical datums of land and sea part, which is developed in this study, is expected to minimize the confusion caused by mismatch of height information in the use of spatial data, and it also can be minimize economic and time losses in various application fields such as coastal development project, coastal disaster prevention, etc.

• Journal of the Korean Association of Geographic Information Studies
• /
• v.21 no.3
• /
• pp.119-126
• /
• 2018

In this study, In this study, the Datum Level-based hydrography surveying system and the ellipsoid-based system were analyzed to acquire more consistent depth data. For the study, the ellipsoid-based surveying for hydrography was conducted twice for the same track line. And the depth was calculated by correcting rise and fall of water level (water level change by tidal energy and other marine environmental energies) respectively by the traditional water level correction method and ellipsoidally referenced water level correction method. there is able to check that Ellipsoid-based hydrographic surveying data is more improved than Datum Level-based hydrographic surveying data in aspect of level difference phenomenon in the same area (surveying line). This result shows that if the Ellipsoid-based hydrographic surveying is performed, the sea level change (tidal energy and other marine environmental energy) of the survey area in real time could be reflected to more consistent generating bathymetric data.

• Fashion & Textile Research Journal
• /
• v.4 no.2
• /
• pp.145-155
• /
• 2002

In order to investigate how upper limb motion gives influence on clothing, this study measured tests by following standards: Front Vertical motion, Side-Vertical motion, and Horizontal motion. For this study, the procedures in the order of alphabet are applied. A. Eeach of testee's pattern was copied by the motion with a method of tight fitting technique. B. Analyzing each of the size-change on measuring item. C. Studying the moving aspects at each datum points. The results shows that the biggest change can be found in the following items. 1) In vertical motion of F4 (the length to shoulder point from A-point) 2) In horizontal motion of F5 (the length to front-width point from A-point), the check-result gained by checking the notice between motions shows that the most noticeable items are F4 (the length to shoulder point from A-point), F5 (the length to front-width point from A-point), F6 (the length to armpit point from A-point), B7 (the length to side-waist point from B-point). In result of the study of datum point's movement by motion, the items which were measured with the longest on straight-distance in vertical motion are the front and rear-shoulder, and the rear-shoulder, front-armpit in horizontal motion each. In the movement of each datum points by length, the check-result gained by checking the notice between motions shows that the most remarkable item is the front-shoulder.

• Journal of the Society of Naval Architects of Korea
• /
• v.47 no.1
• /
• pp.93-98
• /
• 2010

In this paper, PLC which can be installed easily and is stable to transfer datum, is tested for approving its application in a real ship. Internet access service, CCTV monitoring, light control and huge sensor communications are needed for enhancing the convenience and safety of passengers and crew in ships. In order to apply PLC in ships, we surveyed some noises interrupting PLC in ships and investigated the PLC characteristics. The Hannara, a training ship of Korea Maritime University, was used for the test. We measured and analyzed blocking noises using by NI's SCXI-1001. When noises of specific frequency band occurred near the PLC frequency band, PLC transfer capacity was low for mass datum. We developed and verified some methods to apply PLC in a ship under lots of noises.

• Geophysics and Geophysical Exploration
• /
• v.19 no.4
• /
• pp.236-248
• /
• 2016

In this review, the basic concepts of geodetic coordinate system and map projection are explained to practitioners in exploration geophysicists to enhance the understanding of geographic and projected coordinate system. The fundamental elements such as earth ellipsoid, geoid, geocentric and geodetic latitudes, rhumb line, and great circle are dealt with in detail. The geocentric and geodetic coordinate systems are also summarized neatly, together with coordinate conversion formulae. In addition, the concept and technique for datum transforms between local and world datum are presented, with special emphasis on Korean Geodetic System.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.17 no.10
• /
• pp.2359-2368
• /
• 2013

In this paper, an IRD (internal read data) circuit preventing the reentry into the read mode while keeping the read-out DOUT datum at power-up even if noise such as glitches occurs at signal ports such as an input signal port RD (read) when a power IC is on, is proposed. Also, a pulsed WL (word line) driving method is used to prevent a DC current of several tens of micro amperes from flowing into the read transistor of a differential paired eFuse OTP cell. Thus, reliability is secured by preventing non-blown eFuse links from being blown by the EM (electro-migration). Furthermore, a compared output between a programmed datum and a read-out datum is outputted to the PFb (pass fail bar) pin while performing a sensing margin test with a variable pull-up load in consideration of resistance variation of a programmed eFuse in the program-verify-read mode. The layout size of the 8-bit eFuse OTP IP with a $0.18{\mu}m$ process is $189.625{\mu}m{\times}138.850{\mu}m(=0.0263mm^2)$.

• Proceedings of the KSR Conference
• /
• 2003.05a
• /
• pp.651-655
• /
• 2003

The rolling-stocks used in conventional line have suffered wheel problems due to lack of adaptability with track. These brought out severe wheel flange wear, these have caused unstable ride characteristics of rolling-stock. Especially, Wheel flange wear is severely influenced by wheel profile but lateral suspension characteristics. This study was started to induce wheel profile suitable for domestic railway environment. Thus, we analyzed the wear characteristics of wheel profiles that are being applied to railway rolling-stock in KNR. To analyze wheel wear characteristics, we have conducted experiment studies for passenger rolling-stock and obtained useful datum.

• Journal of Mechanical Science and Technology
• /
• v.17 no.5
• /
• pp.629-636
• /
• 2003

This paper introduces the developed geometry PIG (Pipeline Inspection Gauge), one of several ILI (In-Line Inspection) tools, which provide a full picture of the pipeline from only single pass, and has compact size of the electronic device with not only low power consumption but also rapid response of sensors such as calipers, IMU and odometer. This tool is equipped with the several sensor systems. Caliper sensors measure the pipeline internal diameter, ovality and dent size and shape with high accuracy. The IMU (Inertial Measurement Unit) measures the precise trajectory of the PIG during its traverse of the pipeline. The IMU also provide three-dimensional coordination in space from measurement of inertial acceleration and angular rate. Three odometers mounted on the PIG body provide the distance moved along the line and instantaneous velocity during the PIG run. The datum measured by the sensor systems are stored in on-board solid state memory and magnetic tape devices. There is an electromagnetic transmitter at the back end of the tool, the transmitter enables the inspection operators to keep tracking the tool while it travels through the pipeline. An experiment was fulfilled in pull-rig facility and was adopted from Incheon LT (LNG Terminal) to Namdong GS (Governor Station) line, 13 km length.

• Proceedings of the KIEE Conference
• /
• 2001.11b
• /
• pp.377-379
• /
• 2001

Contamination flashover is responsible for insulator electrical failures. Particularly, in Korea, with its perennially dry spring, the first spring rain often cause serious line outages by forming a conductive liquid film on the insulator surface. Rainwater and fog are not normally conductive but unfortunately atmospheric dust deposited on the insulator surface contains soluble salts which may lead to bad condition of insulation by combining watery and salts. Transmission design engineers have used a contamination map drawn on the traditional paper map. But it is not convenient because it does not include the information of Geographic Information accurately. This paper explains the newly developed salt contamination map program using Geographic Information System, which provide accurate geographic information. The program is designed to use four parts of datum, salt contamination levels, 345kV & 154 kV transmission lines, power plants & substations and background map. The digital background map is composed of raster files, the others are done by vector map.