• Clean Technology
• /
• v.24 no.3
• /
• pp.212-220
• /
• 2018

Oxy-fuel combustion is considered as a promising greenhouse gas reduction technology in power plant. In this study, the behaviors of NO and $SO_2$ were investigated under the condition that in-furnace $deNO_x$ and $deSO_x$ methods are applied in oxy-fuel circulating fluidized bed combustion condition. In addition, the generation trends of $SO_3$, $NH_3$ and $N_2O$ were observed. For the purpose, limestone and urea solution were directly injected into the circulating fluidized bed combustor. The in-furnace $deSO_x$ method using limestone could reduce the $SO_2$ concentration in exhaust gas from ~403 to ~41 ppm. At the same experimental condition, the $SO_3$ concentration in exhaust gas was also reduced from ~3.9 to ~1.4 ppm. This trend is mainly due to the reduction of $SO_2$. The $SO_2$ is the main source of the formation of $SO_3$. The negative effect of $CaCO_3$ in limestone, however, was also appeared that it promotes the NO generation. The NO concentration in exhaust gas reduced to ~26 - 34 ppm by appling selective non-catalytic reduction method using urea solution. The $NH_3$ concentration in exhaust gas was appeared up to ~1.8 ppm during injection of urea solution. At the same time, the $N_2O$ generation also increased with increase of urea solution injection. It seems that the HNCO generated from pyrolysis of urea converted into $N_2O$ in combustion atmosphere. From the results in this study, the generation of other pollutants should be checked as the in-furnace $deNO_x$ and $deSO_x$ methods are applied.

• Journal of Power System Engineering
• /
• v.14 no.6
• /
• pp.13-19
• /
• 2010

이 논문에서는 디젤자동차용 LNT와 SCR 촉매의 NO, $NH_3$ 흡착 및 탈리의 기본 특성과 수열화 온도와 시간 및 정량화된 황피독 농도에 대한 de-$NO_x$ 촉매의 내구성을 평가하였다. LNT 촉매는 열적으로 열화됨에 따라 Pt 및 Ba의 소결 및 응집으로 활성이 떨어져 $NO_x$ 전환율은 감소하였다. 반면에 Pt의 비활성화로 중간생성물인 $NH_3$ 생성량은 증가하였으며, 이때 생성된 $NH_3$는 LNT+SCR 복합시스템의 SCR 촉매의 환원제 역할을 담당한다. 1.0 g/L 이상의 황이 피독된 LNT 촉매는 탈황을 하여도 질소 산화물 흡장물질(Ba) 의 성능이 회복이 되지 않아 $NO_x$ 전환율은 회복되지 않았으며, 탈황 후 Pt 재활성화로 인해 NO2 및 SCR 환원제인 $NH_3$ 생성량은 증가하였다. SCR 촉매의 $NO_x$ 전환율은 $700^{\circ}C$ 36h, $800^{\circ}C$ 24h로 수열화 시킨 촉매는 전이금속 입자 성장 및 zeolite 구조 파괴로 인하여 급격하게 떨어졌으며, 0.36 g/L 황 피독된 촉매는 zeolite가 가지는 강산성 특정으로 내피독성이 강하여 탈황시 $NO_x$ 전환율은 회복되었다.

• Applied Chemistry for Engineering
• /
• v.24 no.3
• /
• pp.333-336
• /
• 2013

Experimental investigation to estimate the feasibility of fast selective catalytic reduction (SCR) or oxidation catalyst combined ammonia SCR system to abate NOx in low temperature condition ($150{\sim}250^{\circ}C$) is reported. Because the conversion of NO to $NO_2$ is pre-requisite of the fast SCR process, the effect of the amount of oxidation catalyst to NO conversion to $NO_2$ was tested. 37, 45 and 51% of conversion rates were obtained for the OCV of 563000, 375000 and 281000 h, respectively. $De-NO_x$ performance in the case of $NO_2/NO_x$ ratio of 45% showed the best result in all tested temperature conditions. Comparison of the fast SCR and standard SCR with the condition of $NO_2/NO_x$ ratio of 45%, $200{\sim}250^{\circ}C$ and space velocity of 10000~30000 h showed that the fast SCR does not show much difference according to the variance of space velocity. Also it was shown that using the fast SCR, the volume of SCR catalyst can be reduced less than half of the standard SCR condition by increasing space velocity without the loss of $De-NO_x$ performance.

• Restorative Dentistry and Endodontics
• /
• v.39 no.4
• /
• pp.282-287
• /
• 2014

Objectives: The aim of the present study was to investigate the bond strength of RelyX Unicem (3M) to root canal dentin when used as an endodontic sealer. Materials and Methods: Samples of 24 single-rooted teeth were prepared with Gates Glidden drills and K3 files. After that, the roots were randomly assigned to three experimental groups (n = 8) according to the filling material, (1) AH Plus (Dentsply De Trey GmbH)/Gutta-Percha cone; (2) Epiphany SE (Pentron)/Resilon cone; (3) RelyX Unicem/Gutta-Percha cone. All roots were filled using a single cone technique associated to vertical condensation. After the filling procedures, each tooth was prepared for a push-out bond strenght test by cutting 1 mm-thick root slices. Loading was performed on a universal testing machine at a speed of 0.5 mm/min. One-way analysis of variance and Tukey test for multiple comparisons were used to compare the results among the experimental groups. Results: Epiphany SE/Resilon showed significantly lower push-out bond strength than both AH Plus/Gutta-Percha and RelyX Unicem/Gutta-Percha (p < 0.05). There was no significant difference in bond strength between AH Plus/Gutta-Percha and RelyX Unicem/Gutta-Percha (p > 0.05). Conclusions: Under the present in vitro conditions, bond strength to root dentin promoted by RelyX Unicem was similar to AH Plus. Epiphany SE/Resilon resulted in lower bond strength values when compared to both materials.

• Applied Microscopy
• /
• v.51
• /
• pp.6.1-6.9
• /
• 2021

Histopathology is a well-established standard diagnosis employed for the majority of malignancies, including breast cancer. Nevertheless, despite training and standardization, it is considered operator-dependent and errors are still a concern. Fractal dimension analysis is a computational image processing technique that allows assessing the degree of complexity in patterns. We aimed here at providing a robust and easily attainable method for introducing computer-assisted techniques to histopathology laboratories. Slides from two databases were used: A) Breast Cancer Histopathological; and B) Grand Challenge on Breast Cancer Histology. Set A contained 2480 images from 24 patients with benign alterations, and 5429 images from 58 patients with breast cancer. Set B comprised 100 images of each type: normal tissue, benign alterations, in situ carcinoma, and invasive carcinoma. All images were analyzed with the FracLac algorithm in the ImageJ computational environment to yield the box count fractal dimension (Db) results. Images on set A on 40x magnification were statistically different (p = 0.0003), whereas images on 400x did not present differences in their means. On set B, the mean Db values presented promising statistical differences when comparing. Normal and/or benign images to in situ and/or invasive carcinoma (all p < 0.0001). Interestingly, there was no difference when comparing normal tissue to benign alterations. These data corroborate with previous work in which fractal analysis allowed differentiating malignancies. Computer-aided diagnosis algorithms may beneficiate from using Db data; specific Db cut-off values may yield ~ 99% specificity in diagnosing breast cancer. Furthermore, the fact that it allows assessing tissue complexity, this tool may be used to understand the progression of the histological alterations in cancer.

• Restorative Dentistry and Endodontics
• /
• v.41 no.4
• /
• pp.271-277
• /
• 2016

Objectives: In this study, we evaluated the influence of different radiant exposures provided by single-peak and polywave light-curing units (LCUs) on the degree of conversion (DC) and the mechanical properties of resin cements. Materials and Methods: Six experimental groups were established for each cement (RelyX ARC, 3M ESPE; LuxaCore Dual, Ivoclar Vivadent; Variolink, DMG), according to the different radiant exposures (5, 10, and $20J/cm^2$) and two LCUs (single-peak and polywave). The specimens were made (7 mm in length ${\times}$ 2 mm in width ${\times}$ 1 mm in height) using silicone molds. After 24 hours of preparation, DC measurement was performed using Fourier transform infrared spectrometry. The same specimens were used for the evaluation of mechanical properties (flexural strength, FS; elastic modulus, E) by a three-point bending test. Data were assessed for normality, after which two-way analysis of variance (ANOVA) and post hoc Tukey's test were performed. Results: No properties of the Variolink cement were influenced by any of the considered experimental conditions. In the case of the RelyX ARC cement, DC was higher when polywave LCU was used; FS and E were not influenced by the conditions evaluated. The LuxaCore cement showed greater sensitivity to the different protocols. Conclusions: On the basis of these results, both the spectrum of light emitted and the radiant exposure used could affect the properties of resin cements. However, the influence was material-dependent.

• Clean Technology
• /
• v.24 no.2
• /
• pp.127-134
• /
• 2018

To reduce the environmental pollution by $NO_x$ from ship engine, International maritime organization (IMO) announced Tier III regulation, which is the emmision regulation of ship's exhaust gas in Emission control area (ECA). Selective catalytic reduction (SCR) process is the most commercial $De-NO_x$ system in order to meet the requirement of Tier III regulation. In generally, commercial ceramic honeycomb SCR catalyst has been installed in SCR reactor inside marine vessel engine. However, the ceramic honeycomb SCR catalyst has some serious issues such as low strength and easy destroution at high velocity of exhaust gas from the marine engine. For these reasons, we design to metallic structured catalyst in order to compensate the defects of the ceramic honeycomb catalyst for applying marine SCR system. Especially, metallic structured catalyst has many advantages such as robustness, compactness, lightness, and high thermal conductivity etc. In this study, in order to support catalyst on metal substrate, coating slurry is prepared by changing binder. we successfully fabricate the metallic structured catalyst with strong adhesion by coating, drying, and calcination process. And we carry out the SCR performance and durability such as sonication and dropping test for the prepared samples. The MFC01 shows above 95% of $NO_x$ conversion and much more robust and more stable compared to the commercial honeycomb catalyst. Based on the evaluation of characterization and performance test, we confirm that the proposed metallic structured catalyst in this study has high efficient and durability. Therefore, we suggest that the metallic structured catalyst may be a good alternative as a new type of SCR catalyst for marine SCR system.

• Asian-Australasian Journal of Animal Sciences
• /
• v.26 no.11
• /
• pp.1630-1636
• /
• 2013

An investigation was carried out to assess the carcass characteristics and meat quality aspects of immunocastrated male pigs of medium genetic potential for lean meat deposition in carcass (53 to 55%). When the crossbred Large White x Landrace pigs (n = 45) were 70 days old, they were distributed in a totally randomized design in three treatments (castrated males, females and immunocastrated males) with three replicates of five animals. The pigs were slaughtered when they were 140 days old. Carcass temperature and pH were recorded twice, at 45 min and 24 h after slaughter. The carcasses were evaluated for hot and cold carcass yield, commercial cuts yield, length and depth, back fat thickness, loin eye area and lean meat percentage. The Longissimus dorsi muscle was extracted for analysis of color ($L^*$, $a^*$, $b^*$), exudate loss, cooking loss and centesimal and sensorial analysis of the meat. There were no significant differences for the evaluated parameters between castrated males, immunocastrated males and females, except for backfat thickness between the 7th and 8th thoracic vertebra and the point P2 (lower for immunocastrated males) and carcass temperature at 45 min post slaughter (higher in immunocastrated males), however, this did not interfer with the rate of pH decrease post mortem and the meat quality. The results from this research did not indicate a benefit of immunocastration on carcass characteristics of pigs of medium genetic potential for lean meat deposition in carcass, when compared to surgical castration.

• Asian-Australasian Journal of Animal Sciences
• /
• v.27 no.5
• /
• pp.706-716
• /
• 2014

A new strategy of co-inoculating Bacillus subtilis MA139 with Streptococcus thermophilus and Saccharomyces cerevisiae was used to produce fermented soybean meal (FSBM). Three experiments were conducted to determine the concentration of digestible energy (DE) and metabolizable energy (ME) (Exp. 1), apparent ileal digestibility (AID) and standardized ileal digestibility (SID) of amino acids (AA) (Exp. 2), and feeding value (Exp. 3) of FSBM produced by this new strategy (NFSB) compared with soybean meal (SBM) and conventionally available FSBM (Suprotein). In Exp. 1, twenty-four barrows (initial body weight [BW] of $32.2{\pm}1.7kg$) were randomly allotted to 1 of 4 diets with 6 replicates per diet. A corn basal diet and 3 diets based on a mixture of corn and 1 of 3 soybean products listed above were formulated and the DE and ME contents were determined by the difference method. The results showed that there were no differences in DE and ME between SBM and either FSBM product (p>0.05). In Exp. 2, eight barrows (initial BW of $26.8{\pm}1.5kg$) were fitted with ileal T-cannulaes and used in a replicated $4{\times}4$ Latin square design. Three corn-starch-based diets were formulated using each of the 3 soybean products as the sole source of AA. A nitrogen-free diet was also formulated to measure endogenous losses of AA. The results showed that the SID of all AA except arginine and histidine was similar for NFSB and SBM (p>0.05), but Suprotein had greater (p<0.05) SID of most AA except lysine, aspartate, glycine and proline than NFSB. In Exp. 3, a total of 144 piglets (initial BW of $8.8{\pm}1.2$ kg) were blocked by weight and fed 1 of 4 diets including a control diet with 24% SBM as well as diets containing 6% and 12% NFSB or 12% Suprotein added at the expense of SBM. During d 15 to 28, replacing SBM with 6% NFSB significantly improved average daily gain (ADG) and average daily feed intake (ADFI) (p<0.05) for nursery piglets. During the overall experiment, ADG of piglets fed diets containing 6% NFSB was significantly greater (p<0.05) than that of piglets fed SBM. In conclusion, fermentation with the new strategy did not affect the energy content or the AID and the SID of AA in SBM. However, inclusion of 6% NFSB in diets fed to nursery piglets improved performance after weaning likely as a result of better nutritional status and reduced immunological challenge.

• Journal of Yeungnam Medical Science
• /
• v.15 no.2
• /
• pp.341-349
• /
• 1998

The purpose of this study was to investigate the effects of regular treadmill running on GLUT4 protein of skeletal muscle in STZ-diabetic rats. I used 19 male Sprague-Dawley rats weighing 140 to 160 grams. Rats were randomly assigned into normal, diabetes(DM) and DE(DE) groups. The exercise was loaded with treadmill running for 5 days per week during 4 weeks. All experimental procedures were carried out following overnight fasting 48 hours after last exercise. Gain(gm) in body weight in DM rats(822.4) was lowered compared to normal rats(1092.8), and decreased by exercise. Plasma glucose concentration(mg/dl) in DM rats was 1433.1 which is higher than that of normal group of 1036.4. The concentration of DE group was lower than that of DM rats. Plasma insulin concentration(${\mu}U/ml$) of DM and DE rats was significantly lowerd compared to normal rats. There was no difference of plasma concentrations of FFA and HDL cholesterol among noraml, DM and DE groups. Plasma triglyceride concentration(mg/dl) was significantly highered in DM group compared to those of DM group, the concentration of DE group was lower. Glycogen concentration(mg/gm wet weight) of the plantaris muscle in DM and DE groups was significantly reduced compared to normal group. Glucose transporter 4(GLUT4) protein of soleus was analyzed by Western blot. In DM group, the GLUT4 protein level was markdly decreased compared to normal group, but the level was recovered to the level of normal group by 4 weeks treadmill running. In conclusion, the insulin resistance induced by STZ administration was partially improved by 4 weeks physical training in rats.