• Wind and Structures
• /
• v.34 no.5
• /
• pp.451-467
• /
• 2022

The flow around a high-speed train with three underbody structures in the bogie area is numerically investigated using the improved delayed detached eddy simulation method. The vortex structure, pressure distribution, flow field structure, and unsteady velocity of the wake are analyzed by vortex identification criteria Q, frequency spectral analysis, empirical mode decomposition (EMD), and Hilbert spectral analysis. The results show that the structures of the bogie and its installation cabin reduce the momentum of fluid near the tail car, thus it is easy to induce flow separation and make the fluid no longer adhere to the side surface of the train, then forming vortices. Under the action of the vortices on the side of the tail car, the wake vortices have a trend of spanwise motion. But the deflector structure can prevent the separation on the side of the tail car. Besides, the bogie fairings do not affect the formation process and mechanism of the wake vortices, but the fairings prevent the low-speed fluid in the bogie installation cabin from flowing to the side of the train and reduce the number of the vortices in the wake region.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.12 no.6
• /
• pp.1009-1017
• /
• 2001

The acousto-optical spectrometer is designed by using 1 GHz bandwidth acousto-optic deflector for radio signal analysis. This system is a high resolution wide band spectrometer which uses I GHz bandwidth and a total of 2,048 channel charge coupled device. When we measured the spectrums of signals deflected by acousto-optical spectrometer, we confirmed the stability of the total system by repetitive observations of the same frequency, and each part of the system worked well. We installed this system onto 60 cm radio telescope, and observed 12CO(J= 1 ∼0) emission lines around CRL 2688, IRC 10216 and NGC 5005 Galaxy center. We could observe effectively very narrow band width radio spectrum as well as wide band radio spectrum. We also confirmed high sensitivity and resolution in observation of 12CO(J-10) omission line of NGC 5005 Galaxy center which is a weak signal.

• Journal of the Korean Vacuum Society
• /
• v.10 no.4
• /
• pp.396-402
• /
• 2001

MgO thin films with 1000 $\AA$ thickness were deposited on Cu substrates by using an electron gun evaporator at room temperature. A 1000 $\AA$ thick Al layer was deposited on the MgO for removing the charging effect of the MgO thin film during the measurements of the sputtering yields. A Ga ion liquid metal was used as the focused ion beam(FIB) source. The ion beam was focused by using double einzel lenses, and a deflector was employed to scan the ion beams into the MgO layer. Both currents of the secondary particle and the probe ion beam were measured, and they dramatically changed with varying the applied acceleration voltage of the source. The sputtering yield of the MgO layer was determined using the values of the analyzed probe current, the secondary particle current, and the net current. When the acceleration voltage of the FIB system was 15 kV, the sputtering yield of the MgO thin film was 0.30. The sputtering yield of the MgO thin film linearly increases with the acceleration voltage. These results indicate that the FIB system is promising for the measurements of the sputtering yield of the MgO thin film.

• Journal of the Korean Vacuum Society
• /
• v.16 no.1
• /
• pp.7-14
• /
• 2007

A new horizontal neutron reflectometer has been designed and now under construction at the HANARO, 30 MW research reactor, in Daejon, Korea. We performed simulations of neutron ray-tracing to evaluate the performance of all of the optical components of the instrument with a Monte Carlo technique using McStas. The feasible wavelength of the incident neutron beam is $2.5{\AA}$. It produces a q-range up to $0.126{\AA}^{-1}$ with a supermirror as a deflector. Our studies showed improvement of the performance of the guide tube and monochromators. Although the performance is limited in q-range, it promises to be the first reflectometer in Korea for the study of free surfaces, which is currently in demand.

• International Journal of Aeronautical and Space Sciences
• /
• v.16 no.1
• /
• pp.1-7
• /
• 2015

In order to provide some references for suitability of carrier-based aircrafts, this paper studies the flow field of exhaust jets and its impact on the flight deck. The geometrical models of aircraft carrier and carrier-based aircrafts are firstly built, on which unstructured tetrahedral meshes are generated for numerical analysis. Then, this paper simulates the flow field of exhaust jets to evaluate its impact on the Jet Blast Deflector (JBD) and the flight deck, when four carrier-based aircrafts are ready to start off in the bow. The standard k-${\varepsilon}$ equations, three-dimension N-S equations and the Computational Fluid Dynamics (CFD) theory are used in the analysis process. To solve the equations, the thermal coupling of the wind and the jet flow are also considered. The velocity and temperature distributions are provided with the simulation of the CFD software, FLUENT. The results indicate that: (1) this analytical method can be used to simulate aerodynamic problems with complex geometrical models, and the results are of high reliability; (2) the safety working area, the installation scheme of the JBD and the arrangement of the take-off position can be optimized through analysis.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.180-180
• /
• 2013

반도체, 디스플레이와 같이 저압, 극청정 조건에서 진행되는 공정에서 발생한 오염입자는 수 율에 큰 영향을 미친다. 따라서 공정 중에 발생한 오염입자를 실시간으로 모니터링할 수 있는 장비에 대한 연구가 활발히 진행되고 있다. Particle Beam Mass Spectrometer (PBMS)는 저압에서 실시간으로 나노 입자의 크기를 측정할 수 있는 대표적인 장비 중 하나이다. 입자를 포함한 가스 유동이 PBMS로 유입되면, 우선 입자를 입자빔의 형태로 집속하는 공기역학렌즈를 통과하게 된다. 집속된 입자는 노즐에 의해서 가속되며, 이로 인해 충분한 관성을 가지게 된 입자는 양극과 음극, 필라멘트로 구성된 electron gun에서 전자충돌에 의해 포화상태로 하전된다. 하전한 입자는 electrostatic deflector에서 크기에 따라 분류되어 Faraday detector와 electrometer에 의해 측정된다. 그러나 공기역학렌즈는 입자의 크기가 작아질수록 집속 효율이 급격히 낮아진다는 문제점을 지니고 있다. 이는 입자가 작아질수록 점성에 의한 영향이 관성에 의한 영향보다 커짐으로써 나타나는 현상이다. 최근 이러한 문제점을 해결하기 위해 사중극자를 사용하여 입자를 집속시키는 방법이 대안으로 제시되었다. 사중극자는 서로 마주보는 쌍곡선 형태의 전극구조에 AC 전기장을 인가하는 방식을 사용한다. 사중극자의 중심은 정확히 평형점을 가지게 되며 입자는 사중극자 내에서 진동을 반복하며 평형점을 향해 모이게 된다. 입자의 크기가 작을수록 전기력에 의한 영향을 크게 받으므로 사중극자를 이용한 입자집속 방법은 나노입자의 집속에 있어 공기역학렌즈를 이용한 집속에 비해 이점을 지닌다. 또한 집속 하고자 하는 입자 대상이 바뀔 경우 구조를 바꿔야 하는 공기역학렌즈와 달리 사중극자를 이용한 방법은 AC 전기장을 조절하는 것 만으로 제어가 가능하다. 본 연구에서는 저압 조건에서 나노입자를 집속하기 위한 사중극자의 전극 구조를 이론적인 계산을 통하여 구하였다. 그 결과 0.1 torr의 압력 조건하에서 5~100 nm 범위의 기본 입자를 AC 전압과 진동수를 조절하여 집속할 수 있는 사중극자 형태를 설계하였다.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2017.05a
• /
• pp.513-513
• /
• 2017

홍수 시 하천을 따라 유하되는 유송잡물은 구조물에 집적을 통해 유수의 흐름을 방해하고 구조물 주변의 지반을 약화시키거나 월류로 인한 심각한 피해를 야기 시킨다. 교량의 경우 유송잡물의 집적은 교각의 항력을 증가시켜 전도파괴를 유발시킬 수 있으며, 교각주변 흐름교란을 통한 하상 세굴로 인해 기초부를 파괴시키기도 한다. 또한 통수단면적 증가로 인해 높아진 수위는 제방월류로 인해 재산 및 인명피해를 유발하기도 한다. 본 연구는 이러한 유송잡물의 집적을 억제시키는 저감시설물을 대상으로 연구를 수행하고자 한다. 유송잡물 저감시설 중 우회말뚝을 대상으로 수리모형실험을 수행하고 실규모 실험을 통해 저감효과를 검토하였다. 우회말뚝은 교각 전면부에 상류방향으로 이격되어 설치되는 말뚝형태의 구조물로 유송잡물의 우회를 통해 교각에 집적을 저감하는 목적으로 설치된다. 본 연구에서는 수리실험 및 실규모실험을 통해 우회말뚝의 저감능력 검토를 수행하였으며, 1개의 말뚝을 대상으로 교각과의 이격거리와의 관계를 검토하고자 하였다. 수리모형실험의 결과 유송잡물의 길이가 경간장의 100% 일 경우 저감시설이 없을 경우 교각에 87.6% 집적이 발생하였으나 말뚝이 설치되었을 경우 교각에 직접적으로 집적되는 유송잡물은 없으며 31.7% 유송잡물은 우회말뚝에 집적되는 것으로 나타났다. 실규모 실험의 경우 우회말뚝이 없는 경우 집적률은 60%의 집적이 이루어졌으나 우회말뚝을 설치한 경우 10%의 집적률로 나타났다. 우회 말뚝설치에 따른 저감효과는 발생하였으나 이격거리에 대한 저감능력의 차이는 없는 것으로 나타났다. 그러나 우회말뚝의 이격거리가 길어질수록 말뚝주변에서 회전되어진 유송잡물이 교각에 간헐적으로 집적되는 현상이 관측되었다. 따라서 말뚝의 위치를 선정하기 위해서는 유송잡물의 길이를 고려하여 설치하는 것이 유리할 것으로 판단된다.

• Nuclear Engineering and Technology
• /
• v.53 no.9
• /
• pp.3026-3034
• /
• 2021

Multi-target X-ray tube is a new type X-ray source, and can be applied in many fields such as sensitive X-ray fluorescence analysis and medical imaging. In this work, we report an electric field modulation multi-target X-ray tube, which contains four targets (Cr, Ni, Au, Mo) coated on a Beryllium (Be) window. A four-valve electric field deflector was developed to deflect the electron beam to bombard the corresponding targets. Particle dynamics analysis software was employed to simulate the particle tracking of electron beam. The results show that the 30 keV electron beam could get a 6.7 mm displacement on the target plane by 10⁵ V/m electric field. The focus areas are about 2 mm × 5 mm and 4 mm × 2.5 mm after deflection in two directions. Thermal behavior calculated by ANSYS shows that the designed target assembly could withstand a 10 W continuous power. The optimum target thicknesses and emission spectra were obtained by Geant4 when the thickness of Be window was 300 mm and the electron beam incident angle was 0.141 rad. The results indicate that this multi-target X-ray tube could provide different X-ray sources effectively.

• Journal of the Society of Disaster Information
• /
• v.15 no.2
• /
• pp.214-222
• /
• 2019

Purpose: The purpose of this study is to develop a sprinkler head that can be controlled and initial suppressed by installing it in a rack-type warehouse. Method: Considering the spray radius and spray pattern, various deflectors were designed, and the spray angle, discharge characteristics and protection performance test was conducted, and these results were compared and analyzed. Results: An optimal sprinkler head was developed to protect full load, front side of a commodity with minimum water volume 115L/min. Conclusion: The developed head of K-115 and 1Bar pressure was tested with one tier storage confirming that the fire control is carried out without burning all the loadings. In addition, the vertical distance from the top of the load to the deflector shall be separated by 450mm and installed to allow sufficient discharge to the outer part of the commodity.

• Proceedings of the Korea Association of Crystal Growth Conference
• /
• 1996.06a
• /
• pp.526-526
• /
• 1996

The single crystal of LiTaO3 is well known eletro-optic material as well as the piezoelectric one applied to SAW filter. LiTaO3 has large electro-optic effects, so applied to optical switch, acosto-optic deflector, and optical memory device using photorefractive effects. The crystal growth of SAW-grade LiTaO3 has been studied many aspects, but there is no detail research about optic-grade crystal growth. The conditions of optic-grade LiTaO3 single crystal are as below. The optical transmittance must be over 75%, and axial and radial concentratiom uniformity below 1%. The variation of Curie temperature depending on Li/Ta ratio must be also below 2$^{\circ}C$ and no internal no internal cracks and defects. Because of the limitation of crystal quality, the growing of optic-grade LiTaO3 single crystal is very difficult compared with the growing of SAW-grade. In this research, upper conditions of optic-grade single crystal was investigated after growing of 1 inch diameter and 1.5 inch length LiTaO3 single crystal having no internal cracks and defects using Czochralski method. Curie temperature was determined with DSC and measuring capacitance and lattice parameter was calculated about the grown crystal and ceramic powder samples of various Li/Ta ratio. The result of Tc variation was below 1.2$^{\circ}C$ all over the grown crystal, so it is confirmed that LiTaO3 was grown under congruent melting composition having optical homogeniety. Also, the optical transmittance was about 78%, which was sufficient for optical device.