• 한국정보디스플레이학회:학술대회논문집
• /
• 2008.10a
• /
• pp.1377-1380
• /
• 2008

A development of low power display is an important problem from a point of reduction in worldwide energy consumption. In this research, we aimed to achieve a high quality and low power paper-like reflective full-color display and investigated the design rules for the light diffusing film, LC-cell structure, front lighting systems based on the diffused light control technology. As a result, we successfully obtained the high quality reflective liquid crystal display with a high reflectivity, a wide color gamut and a high motion picture quality.

• Journal of The Institute of Information and Telecommunication Facilities Engineering
• /
• v.9 no.3
• /
• pp.80-85
• /
• 2010

In this paper, we present an algorithm for efficient control of backlight LED in order to reduce the power consumption of LCD TV. In addition, a pragmatic implementation method is presented. In conventional local dimming control, backlight LEDs of LCD TV are divided into $M{\times}N$ blocks. And, the proper luminance for each block is computed according to input image and used for dimming control. But, LED light of each block is diffused and affects the neighboring blocks, so that luminance of each block becomes larger than that of intent. In the proposed algorithm, dimming control values are reduced by the amount of quantity affected by the neighboring blocks using light spread function, resulting in additional reduction of power consumption.

• Journal of Bio-Environment Control
• /
• v.10 no.3
• /
• pp.141-147
• /
• 2001

To compare to the optical and physical properties of covering materials for plastic greenhouse, EVA(ethylene vinyl acetate, 0.08 mm), polyorefine antifog (0.1 mm), fluoric (0.06 mm), diffused (0.15 mm), polyorefine antidrop (0.15 mm) and PET (polyethylene terephthalate, 0.5 mm) films were used. The small greenhouse (5.4$\times$18.5$\times$2.9 m, W$\times$L$\times$H) investigated during 3 years form 1997 to 1999. After covering materials were used for greenhouse covering during 30 months, UV (300-400 nm) transmittances of diffused film and PET were appeared from 25 to 26%, while those of fluoric film and the other films were 76% and from 63 to 67%. For PAR (photosynthetically active radiation, 400-700 nm), the transmittances of fluoric, antidrop, PET, antifog, EVA, and diffused film were 86.5%, 80.5%, 76.3%, 75.5%, 74.1% and 61.9% respectively. The losses of PAR transmittance of EVA and the antidrop film during period between 7 days and 30 months were higher value 12% and lower value 6% than any other film. Under the canopy of tomato plants, light intensities of the diffused film and the antifog film were 2.5 times and 1.4 times higher than those of PET. Tensile resistances of fluoric film at the break point were the higher than those of antifog film and diffused film. While impact resistance of the antidrop film was the highest value, but the fluoric film was the lowest. Air temperature inside the greenhouse for the day showed to be changed the similar light transmittance of the films. But the increasing order of air temperature for the night was PET, fluoric, antidrop, diffused, antifog and EVA film. Especially, air temperature in the PET was 4$^{\circ}C$ higher than that in the EVA. Solar radiations of the fluoric film, the antidrop film, PET and antifog film in the greenhouse were 32%, 15%, 11% and 4% higher than those of PET. However, those of the diffused film was 7% less than PET.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.35 no.8B
• /
• pp.1204-1210
• /
• 2010

In this paper, in order to reduce the power consumption of LCD TV, we present a two-dimensional dimming algorithm for LED BLU(Backlight Unit) using light spread function and a pragmatic implementation method. In conventional two dimensional dimming algorithms, LED BLU is divided into MxN blocks and proper backlight luminance for each block is computed according to input image and used for dimming control. But, LED light of each block is diffused and affects the neighboring blocks so that luminance of each block becomes larger than that of intent. In the proposed algorithm, dimming control values are reduced by the amount of quantity affected by the neighboring blocks using light spread function, resulting in additional reduction of power consumption.

• The Journal of Korean Academy of Prosthodontics
• /
• v.44 no.1
• /
• pp.1-9
• /
• 2006

Purpose: The purpose of this study was to evaluate the efficacy and substitute possibility of a newly developed flowable composite resins as a luting cement for translucent fiber post. Material & Method: Two kinds of 12 mm translucent fiber Post (D.T. Light-Post (Bisco, USA) and FRC Postec (Ivoclar vivadent, Liechtenstein) was inserted into the teflon mold (7 mm diameter, 9 mm long) and Filtek-Flow (3M ESPE. USA), a light activated flowable composite resin, was polymerized for 60 seconds through the post. Also, the post was cut from the tip to 9 mm, 6 mm, 3 mm, and Filtek-Flow was light cured according to each length. For comparison, 60 seconds light-cured and 24 hours self-cured two dual cured resin cement (Duo-cement (Bisco, USA) and 2 Panavia-F (Kuraray, Japan)) samples were prepared as control group. Also cavities (1 mm in width, 1 mm in depth and 12 mm in length) were prepared using acrylic plate and aluminum bar, and flowable composite resin was flied and light cured by the diffused light from the fiber post's side wall. The degree of polymerization was measured according to the distance from curing light using Vickers' hardness test. Result: Within the limitation of this study, the following conclusions were drawn: 1. Vickers' hardness of light cured dual cured resin cement and flowable composite resin decreased from Panavia-F, Filtek-Flow and Duo-cement accordingly (p<0.05). In the dual curing resin cement, light curing performed group showed higher surface hardness value than self cured only group (p<0.05). 2. Surface hardness ratio (light cured through fiber post /directly light cured) of D.T. Light-Post using Filtek-Flow showed about 70% in the 6 mm deep and about 50% in the 12 mm deep FRC Postec showed only 40% of surface hardness ratio. 3. Surface hardness ratio by diffused light from the post's side wall showed about 50% at 6 mm and 9 mm deep, and about 40% at 12 mm deep in D.T. Light-Post. However, FRC Postec showed about 40% at 6 mm deep, and almost no polymerization in 9 mm and 12 mm deep.

• Proceedings of the KIEE Conference
• /
• 1987.07a
• /
• pp.61-63
• /
• 1987

In this paper, we develope a system which can perform signal processing for bar-code laser scanner. This system is composed of optical detector and preprocessor. The former detects the diffused light and converts it into TTL lebel output. The latter discriminator valid data from various raw data and transmits data to micro-processor. The preprocessor consists of edge transition detector, latch signal generator, module counter, register array, adder array, and buffer memory control circuit etc..

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.430.2-430.2
• /
• 2016

The front transparent conductive oxide (TCO) films in thin fill solar cell should exhibit high transparency, conductivity, good surface morphology and excellent light scattering properties. The light trapping phenomenon is limited due to random surface structure of TCO films. The proper control of surface structure and uniform cauliflower TCO films may be appropriate for efficient light trapping. We report light trapping scheme of ICP-RIE glass texturing by SF6/Ar plasma for high roughness and haze ratio of ITO films. It was observed that the variation of etching time, pattern size and Ar flow ratio during ICP-RIE process were important factors to improve the diffused transmittance and haze ratio of textured glass. The ICP-RIE textured glass showed low etching rates due to the presence of metal elements like Al, B, F and Na. The ITO films deposited on textured glass substrates showed the high RMS roughness and haze ratio in the visible wavelength region. The change in surface morphology showed negligible influence on electrical and structural properties of ITO films. The ITO films with high roughness and haze ratio can be used to improve the performance of thin film solar cells.

• Korean Journal of Plant Resources
• /
• v.27 no.1
• /
• pp.102-109
• /
• 2014

This study was carried out to investigate the effects of diffused light materials on marketable yield and quality of sunlight dried red pepper in plastic film house. The after ripening methods were composed of 3 treatments; using electric bulk dryer (Bulk), sealing house (House), and PE sealing. The diffused light materials were control, tent, shading 35% (Shading net), white polypropylene (PP (white)), and black polypropylene (PP (Black)). The marketable yield was high in order of Bulk as 300 g, House as 275 g, and PE sealing as 112 g. The redness of PE sealing was the highest as 17.85 and that of Bulk was the lowest as 10.65. There was significant difference in redness among the treatments. The moisture content of red pepper was the most rapidly reduced in control, and was the most slowly reduced in Shading net treatment. The marketable yield index was the higher in PP (white) as 114% than control. The redness had a significant difference in PP (Black) and tent compared to the other treatments. The capsaicin content showed the highest as $160mg{\cdot}100g^{-1}$ in PP (white) treatment. Conclusively, the most effective method for sunlight drying red pepper was House with PP (White) treatment. It delayed drying for 2 days but increased marketable yield at 114% than control when sunlight dried red pepper in plastic house. Our results also provided an optimized method for improvement of drying red pepper with sunlight, and will be useful for further drying red pepper research.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2012.05a
• /
• pp.100.2-100.2
• /
• 2012

Surface texturing of crystalline silicon is carried out in alkaline solutions for anisotropic etching that leads to random pyramids of about $10{\mu}m$ in size. Recently textured pyramids size gradually reduced using new solution. In this paper, we investigated that texture pyramids size had an impact on emitter property and front electrode (Ag) contact. To make small (${\sim}3{\mu}m$) and large (${\sim}10{\mu}m$) pyramids size, texturing times control and one side texturing using a silicon nitride film were carried out. Then formation and quality of POCl3-diffused n+ emitter in furnace compare with small and large pyramids by using SEM images, simulation (SILVACO, Athena module) and emitter saturation current density (J0e). After metallization, Ag contact resistance was measured by transfer length method (TLM) pattern. And surface distributions of Ag crystallites were observed by SEM images. Also, performance of cell which is fabricated by screen-printed solar cells is compared by light I-V.

• 한국신재생에너지학회:학술대회논문집
• /
• 2009.06a
• /
• pp.176-179
• /
• 2009

ZnO:Al 투명전도막을 유리기판위에 in-line RF-magnetron sputtering법으로 증착온도 및 증착압력에 따라 제조하고, 습식식각에 따른 박막의 표면형상 및 광학적 특성변화를 조사하였다. 초기박막은 육방정계(Hexanonal wurtzite)의 결정 구조와 (002)면의 c-축 우선배향성을 갖으며 가시광 영역에서 높은 광 투과도(T $\geq$ 80%)와 낮은 비저항($\rho\;=\;5.2{\times}10^{-4}{\Omega}{\cdot}cm$)의 특성을 나타내었다. 습식 식각 후 박막의 표면형상은 식각 전 박막의 결정성에 큰 의존성을 보이며 본 연구에서는 1 mTorr의 낮은 증착압력과 $350^{\circ}C$의 높은 증착온도에서 증착된 결정성이 우수한 막에서 높고 균일한 형태의 crater를 갖는 표면형상을 얻을 수 있었다. 균일한 crater를 형성하는 ZnO:Al 박막은 hill 형태의 표면형상을 갖는 상용 Asahi-U glass에 비하여 높은 Haze ($T_{diffused}/T_{total}$)값과 넓은 산란각을 나타내어 향상된 광 산란특성을 갖으며 이는 실리콘 박막 태양전지내로 입사된 광의 산란경로를 증가시켜 태양전지 성능을 크게 향상시킬 수 있을 것으로 기대한다.