• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.46 no.11
• /
• pp.50-55
• /
• 2009

In this paper, a distributed amplifier is designed using distributed network synthesis that provides the optimum absorption capability of a capacitance. Transfer functions of filters, which consist of the amplifier, are synthesized by a low-pass Chebyshev approximation. Capacitances that a filter network can absorb are calculated as a function of its minimum insertion loss(MIL) and ripple. Active devices in a distributed amplifier are modeled as equivalent circuits by using their S-parameters, and their equivalent capacitances are absorbed into filter structures by properly adjusting the MIL and ripple of a transfer function. As an application example, a distributed amplifier with the gain of about 12.5dB is designed that operates over the frequency range between 0.1 and 7.5GHz. Experimental results prove that distributed network synthesis, which considers capacitance absorption capability, is useful to the design of distributed amplifiers.

• Proceedings of the IEEK Conference
• /
• 2000.06b
• /
• pp.84-87
• /
• 2000

In this paper, a high gain-broad bandwidth MMIC distributed amplifier was designed using cascaded single section distributed amplifier configuration. The PHEMT for this studies was fabricated at our lab The PHEMT has a 0.2 $\mu\textrm{m}$ gate length. a 80 $\mu\textrm{m}$ unit gate width and 4 gate fingers. A designed MMIC amplifier have higher S$\sub$21/ gain than the common distributed amplifier using the same number of active devices. From the simulated result, we obtained that the S$\sub$21/ gain of DC ∼ 20 GHz bandwidth was 15.6 dB and flatness was ${\pm}$0.9 dB, and input and output reflection coefficient were lower than -8 dB. The simulated gain shows an improvement 7.3 dB compared with those of conventional distributed amplifier. And the chip size is 2.0 ${\times}$ 1.2 $\textrm{mm}^2$.

• ETRI Journal
• /
• v.39 no.5
• /
• pp.737-745
• /
• 2017

A 6-GHz-to-18-GHz monolithic nonuniform distributed power amplifier has been designed using the load modulation of increased series gate capacitance. This amplifier was implemented using a $0.25-{\mu}m$ AlGaN/GaN HEMT process on a SiC substrate. With the proposed load modulation, we enhanced the amplifier's simulated performance by 4.8 dB in output power, and by 13.1% in power-added efficiency (PAE) at the upper limit of the bandwidth, compared with an amplifier with uniform gate coupling capacitors. Under the pulse-mode condition of a $100-{\mu}s$ pulse period and a 10% duty cycle, the fabricated power amplifier showed a saturated output power of 39.5 dBm (9 W) to 40.4 dBm (11 W) with an associated PAE of 17% to 22%, and input/output return losses of more than 10 dB within 6 GHz to 18 GHz.

• Proceedings of the IEEK Conference
• /
• 1999.06a
• /
• pp.265-268
• /
• 1999

In this paper, a wideband MMIC distributed amplifier was designed using the fabricated PHEMT with the unit gate width of 80 ${\mu}{\textrm}{m}$ and 4 gate fingers at our Lab. S$_{21}$ gains are 7.1 ~ 10.0 ㏈. Input and output reflection coefficients obtained from the distributed amplifier in the frequency range of DC~25 ㎓ are lower then -8 ㏈. A chip size of the designed wideband MMIC distributed amplifier is 1.9 mm $\times$ 1.1 mm.

• Proceedings of the KAIS Fall Conference
• /
• 2009.05a
• /
• pp.415-417
• /
• 2009

본 논문에서는 초광대역 특성을 보이는 직렬 분포형 증폭기(Cascaded single stage distributed amplifier)에 대하여 기술한다. 직렬 분포형 증폭기는 다단 증폭기 중 하나인 분포형 증폭기(Distributed amplifier)보다는 높은 이득을 얻을 수 있다. 본 논문에서는 분포형 증폭기에 대한 간단한 이론을 설명한 뒤 직렬 분포형 증폭기에 대한 이론을 기술하고 실제 구현하여 측정을 결과를 제시한다.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.16 no.5 s.96
• /
• pp.482-487
• /
• 2005

In this paper, we propose the control method of output impedance of each cascode unit cell of distributed amplifier by connecting varactors in the gate-terminal of common gate. Compared to common source unit cell, cascode unit cell has many advantages such as high gain and high output impedance as well as negative resistance loading. But if the transistor model which is used in design is inaccurate and process parameter is changed, oscillation sometimes can occur at band edge in which the gain start to drop. Therefore, we need control circuit which can prevent oscillation, although the circuit has already fabricated, and varactor connected to gate-terminal of common gate of cascode gain cell can play that part. Measured result of fabricated distributed amplifier shows the capability of contol of gain characteristic by adjusting of value of varactors, this can guarantee the stability of the circuit. The gain is $8.92\pm0.82dB$ over 49 GHz, the group delay is $\pm9.3 psec$ over 41 GHz. All transistor which has $0.15{\mu}m$ gate length is GaAs based p-HEMT, and distributed amplifier is put together with 4 stages.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.10 no.8
• /
• pp.1817-1823
• /
• 2009

A design of cascaded distributed amplifier with a broadband amplification is described in this paper. A medium power device with 23dBm, max output power under the optimal narrow-band power matching condition is adopted for the design and fabrication of the cascaded distributed amplifier. In general, conventional distributed amplifiers with the parallel connected input ports have a low gain, and previous cascaded distributed amplifiers show a relatively low output power of 10dBm at most, which is the upper limit of small signal amplification. However, the cascaded distributed amplifier in this paper shows the gain of $18.15{\pm}0.75dB$ and output power of 20dBm over $300MHz{\sim}2GHz$ from the measurement, so it can be well adopted as a wideband driver amplifier.

• Journal of IKEEE
• /
• v.22 no.4
• /
• pp.1088-1092
• /
• 2018

In this paper, we propose a dual-mode frequency tripler using push-push and stacked FET structures. The proposed circuit can operate either in frequency multiplier mode or in amplifier mode. In the frequency multiplier mode, push-push frequency multiplication is achieved by allowing input signals with particular phase shifts. In the amplifier mode, the device operates as a distributed amplifier to obtain high gain. Also both modes were designed using stacked FET structure. The designed circuit showed frequency tripled output power of 9.7 dBm at 2.4 GHz with the input at 800 MHz. On the other hand, in the amplifier mode, the device showed 8.9 dB of gain to generate 19.5 dBm at 800 MHz.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.2 no.2
• /
• pp.125-131
• /
• 2002

This paper presents MMIC drive and power amplifiers covering 6-18 ㎓. For simple wideband impedance matching and less sensitivity to fabrication variation, modified distributed topologies are employed in the both amplifiers. Cascade amplifiers with a self-biasing circuit through feedback resistors are used as unit gain blocks in the drive amplifier, resulting in high gain, high stability, and compact chip size. Self impedance matching and high-pass, low-pass impedance matching networks are used in the power amplifier. In measured results, the drive amplifier showed good return losses ($S_11,{\;}S_{22}{\;}<{\;}-10.5{\;}dB$), gain flatness ($S_{21}={\;}16{\;}{\pm}0.6{\;}dB$), and $P_{1dB}{\;}>{\;}22{\;}dBm$ over 6-18 GHz. The power amplifier showed $P_{1dB}{\;}>{\;}28.8{\;}dBm$ and $P_{sat}{\;}{\approx}{\;}30.0{\;}dBm$ with good small signal characteristics ($S_{11}<-10{\;}dB,{\;}S_{22}{\;}<{\;}-6{\;}dB,{\;}and{\;}S_{21}={\;}18.5{\;}{\pm}{\;}1.25{\;}dB$) over 6-18 GHz.

• Journal of Electrical Engineering and Technology
• /
• v.8 no.3
• /
• pp.610-612
• /
• 2013

A novel balanced distributed amplifier (DA) was proposed using novel impedance transforming MEMS baluns. The impedance transforming MEMS balun is matched to $50{\Omega}$ at one input port and $25{\Omega}$ at two output ports. It is based on the electric field mode-change method, thus it is strongly independent of frequency and very compact. The novel balanced DA consists of two $25{\Omega}$-matched DAs and these are combined by $50{\Omega}$-to-$25{\Omega}$ baluns. Theoretically, it has two times wider bandwidth and power capability than the conventional DA. So as to verify the proposed concept, we designed and fabricated a conventional DA and the proposed one using 0.15-${\mu}m$ GaAs pHEMT technology.