• 한국전산유체공학회:학술대회논문집
• /
• 2009.04a
• /
• pp.19-19
• /
• 2009

Dynamic Stall is a flow phenomenon which occurs on the retreating side of helicopter rotor blades during forward flight. It also occurs on blades of stall regulated wind turbines under yawing conditions as well as during gust loads. Time scales occurring during this process are comparable on both helicopter and wind turbine blades. Dynamic Stall limits the speed of the helicopter and its manoeuvrability and limits the amount of power production of wind turbines. Extensive numerical as well as experimental investigations have been carried out recently to get detailed insight into the very complex flow structures of the Dynamic Stall process. Numerical codes have to be based on the full equations, i.e. the Navier-Stokes equations to cover the scope of the problems involved: Time dependent flow, unsteady flow separation, vortex development and shedding, compressibility effects, turbulence, transition and 3D-effects, etc. have to be taken into account. In addition to the numerical treatment of the Dynamic Stall problem suitable wind tunnel experiments are inevitable. Comparisons of experimental data with calculated results show us the state of the art and validity of the CFD-codes and the necessity to further improve calculation procedures. In the present paper the phenomenon of Dynamic Stall will be discussed first. This discussion is followed by comparisons of some recently obtained experimental and numerical results for an oscillating helicopter airfoil under Dynamic Stall conditions. From the knowledge base of the Dynamic Stall Problems, the next step can be envisaged: to control Dynamic Stall. The present discussion will address two different Dynamic Stall control methodologies: the Nose-Droop concept and the application of Leading Edge Vortex Generators (LEVoG's) as examples of active and passive control devices. It will be shown that experimental results are available but CFD-data are only of limited comparison. A lot of future work has to be done in CFD-code development to fill this gap. Here mainly 3D-effects as well as improvements of both turbulence and transition modelling are of major concern.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.32 no.5
• /
• pp.10-17
• /
• 2004

To achieve the advanced forward flight performance of helicopter, the passive control methods for enhancement of the dynamic stall characteristics of rotor blades are studied. To enhance the dynamic stall characteristics of the rotor blades, it is essential to improve the lift performance and the pitching moment performance simultaneously with the control of the separation on the rotor blades. For this point of view, both the fixed droop leading edge and the Gurney flap which are simply realized are used for control of the dynamic stall in severe dynamic stall conditions. From this study, the combination of both passive control methods showed dramatic enhancement of lift and pitching moment performance in dynamic stall than previous research results.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.8 no.3 s.22
• /
• pp.116-123
• /
• 2005

An experimental investigation on the static and dynamic stall characteristics of elliptic airfoil was performed by PIV velocity field measurements. The flow Reynolds number was $3.13{\times}10^5$ and the reduced frequency of the pitch oscillation ranged from 0.075 to 0.125. The onset of static stall was caused by boundary layer separation which started at the trailing edge and progressed toward the leading edge. However, dynamic stall was caused by the vortex shed at the leading edge region and the flow field showed a vortex dominated flow with turbulent separation and alternate vortex shedding. The increase of reduced frequency increased the dynamic stall angle of attack and intensified the flow hysteresis in the down-stroke phase.

• 한국전산유체공학회:학술대회논문집
• /
• 2004.10a
• /
• pp.115-119
• /
• 2004

The effect of a continuous blowing or suction on an oscillating 2-D NACA0012 airfoil was investigated numerically for the dynamic stall control. The influence of control parameter variation was also studied in the view point of aerodynamic characteristics. The result showed that the blowing control kept a higher lift drag ratio before stall angle but the dynamic stall angle was not exceed to without control result. As the slot position was closer to leading edge, the positive control effect becomes greater. The stronger jet and the smaller jet angel made more favorable roles on the control performance. In the cases of the suction, the overall control features were similar to those of the blowing, but dynamic stall angle was increased, i.e. suction was more effective to control dynamic stall. It was also founded that the suction control was showed better control effect as the slot position moves to trail edge within thirty percentage of chord length. In the simulation for the jet strength and the jet angle control, the same tendencies were observed to those of blowing cases.

• 한국전산유체공학회:학술대회논문집
• /
• 2010.05a
• /
• pp.37-39
• /
• 2010

Aerodynamic analysis was done for a fuselage and wing configuration of a mid-sized aircraft using 3-dimensional Navier-Stokes solver. Various turbulent models including a transitional SST were implemented to observe a dynamic stall as well as cruise characteristics. Also, different mesh moving methods were evaluated. Flow hysteresis which causes dynamic stall was investigated through flow field investigations.

• 한국전산유체공학회:학술대회논문집
• /
• 2003.10a
• /
• pp.291-293
• /
• 2003

This paper deals with a thrust generation of flapping-airfoil by dynamic stall. From many other previous research results, phase angle $ between pitching and plunging mode of flapping motion must be 90 deg. to satisfy maximum propulsive efficiency. In this case, leading edge vortex is relatively small. This phenomenon is related dynamic stall. So preventing leading edge vortex induced by dynamic stall guarantees maximum propulsive efficiency. But, in this paper we insist the leading edge vortex yields quite a positive influence on thrust generation and propulsive efficiency. In order to certify our opinion, pitching and plunging motions were calculated with the parameter of amplitude and frequency by using the unsteady, incompressible Navier-Stokes flow solver with a two-equation turbulence model. For more efficient computation, it is parallelized by MPI programming method.

• 한국신재생에너지학회:학술대회논문집
• /
• 2009.11a
• /
• pp.478-481
• /
• 2009

As a first step for aerodynamic analysis of vertical axis wind turbine, dynamic stall characteristics of airfoil was investigated. Dynamic stall of wind turbine airfoil is caused by severe variation of angle of attack and relative velocity of flow around airfoil. Angle of attack and relative velocity can be expressed with tip speed ratio. Variation of angle of attack is strongly dependent on the tip speed ratio. For tip speed ratio, 1.4 and free stream velocity, 15m/s, dynamic stall characteristics of wind turbine airfoil is compared with those of oscillating airfoil having same angle of attack variation.

• 한국전산유체공학회:학술대회논문집
• /
• 2002.10a
• /
• pp.35-40
• /
• 2002

This paper deals with a thrust generation on flapping-airfoil by dynamic stall. Dynamic stall refers to a series of complicated aerodynamic phenomena accompanied by a stall delay in unsteady motion. In most cases, once it occurs, the dynamic stall may lead to an abrupt fluctuation of aerodynamic forces. An inverse $k\acute{a}rm\acute{a}n$ vortex has been considered as a main reason for a thrust generation. In this paper, however, we have found out that a thrust is closely related to reduced frequency and leading edge vortex in addition to inverse Karman vortex. In order to certify our opinion, picking and plunging motions were calculated with the parameter of amplitude and frequency by using the unsteady, incompressible Navier-Stokes flow solver with a two-equation turbulence model. For more efficient computation, it is parallelized by MPI programming method.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.30 no.8
• /
• pp.10-20
• /
• 2002

The present paper investigates methods to control dynamic stall using an optimal approach. An unsteady aerodynamic sensitivity analysis code is developed by a direct differentiation method from a two-dimensional unsteady compressible Navier-Stokes solver including a two-equation turbulence model. Dynamic stall control is conducted by minimizing an objective function defined at an instant instead of integrating for a period of time. Unsteady sensitivity derivatives of the objective function are calculated by the sensitivity code, and optimization is carried out using a linear line search method at every physical time step. Numerous examples of dynamic stall control using control parameters such as nose radius, maximum thickness of airfoil, or suction show satisfactory results.

• Journal of computational fluids engineering
• /
• v.16 no.1
• /
• pp.48-52
• /
• 2011

Aerodynamic analysis was done for a fuselage and wing configuration of a mid-sized aircraft using unsteady 3-dimensional Navier-Stokes solver. Various turbulent models including a transitional SST were used to observe a dynamic stall as well as cruise characteristics. Also, different mesh moving methods were evaluated. Flow hysteresis which causes dynamic stall was investigated through flow field investigations.