• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 1998.10a
• /
• pp.176-179
• /
• 1998

In general, machining time by electrical discharge machining (EDM) process is much longer than that of cutting process, so rough-cut has done for the purpose of reducing machining time prior to EDM Nowadays EDM speed is improving due to the advance of EDM capacity. Therefore a new method, machining a raw material directly by EDM without rough-cut, is used widely. EDM area is varies according to the EDM position in three-dimensional EDM process, so EDM parameters should be determined adaptively based on the EDM area to increase productivity. However it is difficult to calculate EDM area corresponding to the EDM position the EDM workers who have experience in shop floor determine machining parameters by experience. This paper proposes a method for determining EDM parameters based on EDM area corresponding to EDM position.

• Korean Journal of Computational Design and Engineering
• /
• v.6 no.3
• /
• pp.206-214
• /
• 2001

This paper describes the wire EDM (Electric Discharge Machining) CAM system considering a variable taper wire-cut and an unmanned wire EDM during the night. Wire EDM is applicable to all materials that are fairly good electrical conductors, including metals, alloys and most carbide. Thus it provides a relatively simple method for making holes of any desired cross section in materials that are too hard or brittle to be machined by most other methods. In this paper we classify variable taper wire-cut machining patterns and variable taper wire-cut geometries. Also we determine unmanned wire EDM patterns fur the productivity of wire EDM industry. Developed system consists of two modules: 1) Variable taper wire EDM module guarantees the length ratio machining function, the parametric ratio machining function and the marking function. 2) Unmanned wire EDM module guarantees the automatic wire EDM during the night. The proposed system has been tested in the fields and found to be a useful system.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.22 no.4
• /
• pp.367-374
• /
• 2004

In order for the measurement results of an electro-optical distance meter(EDM), which is widely used in surveying, to be reliable, an EDM should be calibrated. For the calibration of an EDM, we have settled a traceability chain, which connects the EDM under calibration to the definition of metre. The chain starts from the iodine stabilized He-Ne laser which realizes the definition of metre, and then connected to a stabilized laser interferometer, a standard EDM, and finally to the EDM under calibration through the baseline. We achieved the expanded calibration uncertainties of the scale and length measurement of an EDM being evaluated to be 6$\times$10$^{-6}$ and 0.2 mm, respectively. Two different calibration methods, and their results are compared.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 1998.03a
• /
• pp.35-39
• /
• 1998

Determination of effective EDM parameters is significant to increase productivity. However, With the complexity of EDM phenomena, a universal selection method of EDM parameters has not been established yet. Moreover, No attempt has been tried before to suggest a logical method in determining essential machining parameters for effective electrical discharge machining. Peak current, one of the most significant factors in EDM, is proportional to EDM area. This paper presents a method that can be Z-map modeling from CMM data, and calculate EDM area using Z-map.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.17 no.4
• /
• pp.76-82
• /
• 2018

3D formed Electrical Discharge Machining (EDM) and hole EDM were conducted for die and mold manufacturing with electrodes which were made by mechanical machining and wire EDM. It is difficult to machine the hardened material after heat treatment and quenching with traditional machining. The only method of machining hardened material is die-sinking EDM. In this research, hole EDM was conducted for heat-treated cold-worked tool steel (SKD11) for use as a die material. The EDM surfaces were analyzed by pulse-on time and peak current of EDM current, according to the machining conditions of EDM. The EDM surface profiles were affected by the peak current. The contribution of each factor is peak current (91.63%) and pulse-on time (0.93%). The best surface roughness was obtained with a $130{\mu}s$ pulse-on time and a 14.2 A peak current. With uniform EDM processing, the surface deteriorated with increasing pulse-on time and peak current. The thickness of the solidified layer induced by EDM was increased as the peak current, crater shapes, and erupted shapes of EDM surfaces were increased. Therefore, microcracking gaps induced by surface tension were increased.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.5 no.6
• /
• pp.511-514
• /
• 2004

Punch and die plate which are press die parts can be made using machine tool or using both machine tool and W-EDM. When machine tool is used, the die life is 2,000,000 to 230,000 strokes. But with W-EDM, the die life is 700,00 to 800,000 strokes. This can be caused by the process deformation layer after W-EDM. SEM pictures of processed section before and after W-EDM are taken to see if the process deformation layer appeared. Also the elimination method is studied.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.7 no.4
• /
• pp.545-549
• /
• 2006

W-EDM is generally used to manufacture punches and die plates from among press mold parts. Before W-EDM was used, however, punches and die plates manufactured via mechanical processing were used to manufacture products, with the die life of the mold expiring after 2,000,000~2,300,000 products have been manufactured. When the mold manufactured through W-EDM was used, however, its service life expired only after 700,000~800,000 products have been manufactured. Since this was attributed to the deformed layer formed after using W-EDM, the surfaces before and after W-EDM was used were scanned using SEM to verify the occurrence of such layer. This study sought to come up with a method of eliminating such phenomenon.

• Journal of the Korean Society for Precision Engineering
• /
• v.27 no.1
• /
• pp.11-17
• /
• 2010

This study investigates the non-traditional manufacturing process of dry wire electrical discharge machining (EDM) in which liquid dielectric is replaced by a gaseous medium. Wire EDM experiments of thin workpieces were conducted both in wet and dry EDM conditions to examine the effects of spark cycle (T), spark on-time ($T_{on}$), thickness of work pieces, and work material on machining performance. The material removal rate (MRR) in the dry wire EDM case was much lower than that in the wet wire EDM case. In addition, the thickness of workpiece and work-material were found to be critical factors influencing the MRR for dry EDM process. The relative ratios of spark, arc and short circuit were also calculated and compared to examine the effectiveness of processes of dry and wet wire EDM.

• Journal of the Korean Society for Precision Engineering
• /
• v.27 no.1
• /
• pp.119-124
• /
• 2010

This paper addresses the design and fabrication of desktop die-sinking dry electrical discharge machining (EDM) system and its experimental performance analysis. The developed desktop dry EDM machine has the horizontal configuration with the size of $300{\times}200{\times}260mm$. The experimental performance analysis is conducted to investigate the effects of EDM conditions and dielectric gas temperature on the surface roughness of EDMed slots and number of EDM sparks. The experimental results demonstrate that low feed rate and large electrode displacement are good for better surface roughness and more number of EDM sparks. In addition, low temperature of dielectric gas results in better surface roughness.

• Journal of the Korean Society for Precision Engineering
• /
• v.21 no.8
• /
• pp.136-142
• /
• 2004

This paper deals with the design and implementation of an open architecture CNC system for Wire-EDM, with a consideration of the difference between Wire-EDM and NC cutting machines. Recent open architecture controller(OAC) related research results could be applied to directly access Wire-EDM systems at the CNC level. However, previous research about OAC is mostly aimed at NC cutting machines such as milling or lathes, and hence these results are inadequate to apply to Wire-EDM. To close the gap between previous general research on OAC and Wire-EDM specific needs, an open architecture NC model for Wire-EDM composed of a synchronization kernel and a NC functional module is proposed. Based on the control information flow and Wire-EDM specific machining process, the conceptual CNC model and the detailed implementation model for Wire-EDM is suggested.