• Journal of the Korean Society of Industry Convergence
• /
• v.5 no.4
• /
• pp.295-299
• /
• 2002

Specific fuel consumption or specific power output characteristics of an internal combustion engine are likely, in conventional applications, the most important operating criteria. In this work, the test method for the engine performance was introduced in a compression ignition(diesel) engine.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.22 no.2
• /
• pp.428-436
• /
• 1998

A TCS slip control system improves acceleration capability and steerability on slippery roads through engine torgue and/or brake torque control. This research mainly deals with the engine control algorithm via the adjustment of the engine throttle angle. The following new control strategy is proposed and investigated ; the TCS slip controller whose input is the difference between the desired driving wheel speed corresponding to the optimum slip ratio and the actual speed yields the target engine torque and then estimates the throttle angle based on the engine performance curve. Various simulation and hardware-in-the-loop simulation have been carried out. The results show the proposed strategy may compensate for the inherent nonlinearity between variation of the throttle angle and variation of the engine torque and produce better performance than the previous strategies without the engine map, especially in the high speed region.

• Proceedings of the Korean Society of Marine Engineers Conference
• /
• 2005.11a
• /
• pp.73-74
• /
• 2005

Shipping company and operators have to manage well to keep shipping schedules without problems in main engine. Specially operators have to operate main engine within the limit of operation point, and adjust related parameters to be operated safely and continuously. Also operators have ability to analyze fouling condition of hull through comparing data gotten from P-V curve and performance results of new building ships in trial with service ships. In this study, not only compared main engine performance results in shop trial and sea trial, but also investigated performance trend in accordance with the time elapsed for the service ship's diesel engine. They were confirmed as follows. First, shop trial load is higher than sea trial load but ship's speed is satisfied with owner's contract speed. Second as time goes by, load of service ship increases steadily and other parameters related with main engine shows variable change depend on main engine load increasing.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2009.04a
• /
• pp.92-97
• /
• 2009

The performance of cooling fan is affected by many peripheral parts, such as radiator, condenser, engine block and etc. Higher power has been requested in more confined automobile engine room. Thus, cooling performance becomes very important to remove the heat generated from the automobile engine more efficiently. In this paper, the performance of cooling fan including effects of engine block is investigated by using a fan tester based on the ASHRAE and the AMCA standards. A flow rate - gap distance curves and a flow rate - engine block constant curves are obtained from this study.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2009.10a
• /
• pp.143-149
• /
• 2009

Recently, according to the tendency to the more comfortable automobile, the improvement of performance of the cooling fan is required. The performance of cooling fan is affected by many peripheral parts, such as radiator, condenser, engine block and etc. Therefore, it is important to consider the effect of peripheral components on the fan performance in design and analysis stages. In this paper, the performance of automobile cooling fan is investigated experimentally by using the large capacity fan tester based on the ASHRAE and the AMCA standards. In particular, the various spacing between cooling fan and engine block are considered to obtain the effect of engine block. An empirical relation between the fan flow rate and the spacing was proposed.

• Journal of the korean Society of Automotive Engineers
• /
• v.11 no.6
• /
• pp.89-96
• /
• 1989

Engine analyzer is developed with the aids of personal computer, A/D converter, interfacing signal transducer and data processing computer programs. The objective of this development are that it should firstly be produced at the resonable low price compared with imported one taking advantage of using existing personal computer and printer, and it should also give good quality of performance. For the attainment of this objective, A/D converter should have been developed to meet the price limit of the equipment. The experiment is performed in a 4 cycle 4 cylinder gasoline engine by this analyzer, and all the information which are necessary for the combustion analysis can be obtained through the processing of the pressure data that are stored in the computer. These are pressure-volume curve, pressure-crank angle curve, the rate of pressure rise and heat release versus crank angle curve etc. With this developed experimental system of resonable price, it will be considered that more easy way of engine data pick-up and processing is possible.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.9 no.4
• /
• pp.10-17
• /
• 2001

The performance of a radiator is generally determined using a wind tunnel, in which the air velocity is uniform. However, when it is installed in a car, the distribution of the air velocity becomes nonuniform due to front-end openings, cross members, and horns etc., resulting in lower performance. In this study, several underhood flow simulations have been first performed to get flow rates and velocity distributions over the radiator. Secondly heat release rates are calculated by both a performance curve and a radiator model. Finally, using an engine cooling system simulator, radiator-top-tank temperature is predicted and the variations of heat release rate and radiator-top-tank temperature with nonuniformity of air velocity distributions are analyzed. The results show that the current engine cooling model successfully accounts for the nonuniformity effects that should be considered for higher accuracy in predicting engine cooling performance.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.19 no.3
• /
• pp.89-95
• /
• 2015

Performance test was conducted for an oxidizer pump and a fuel pump for a 7 ton class rocket engine, by using water. The pumps were driven by an electric motor. The hydrodynamic performance and the suction performance were measured at flow ratio of the design and off-design conditions. Head-flow curve, efficiency-flow curve, and head-cavitation number curve were obtained. It is confirmed that the pumps can satisfy the design requirements of hydrodynamic performance in terms of the head and the efficiency. The pumps also satisfied the design requirements of suction performance.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.21 no.3
• /
• pp.157-164
• /
• 2013

A damper clutch in automatic transmission systems has some advantages of fuel economy and dynamic performance. Although a damper clutch operation improves a fuel economy of the vehicles, a positive operation of a damper clutch in a low vehicle speed induces abnormal vibration. This paper analyzed one of reasons for abnormal vibration by a damper clutch operation in low engine speed ranges. A simulation model was designed to confirm the effects of a damper clutch operation under unstable regions of an engine. A theoretical analysis was carried out about an engine operation stability. Simulation was conducted to depict abnormal vibration by a damper clutch operation in unstable regions of an engine performance curve. The effects of an engine operation region for abnormal vibration by a damper clutch was investigated according to the range and the slope of unstable regions. As a result of simulations, a damper clutch operation would be better to avoid an engine unstable regions.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.32 no.4
• /
• pp.249-254
• /
• 2008

Hydrodynamic performance test of a turbopump for a liquid rocket engine is carried out. The turbopump is composed of an oxidizer pump, a fuel pump and a turbine, and the two pumps are driven by the turbine. In the test, water is used for the pumps as working media and air is used for the turbine. Performance parameters of pumps and a turbine are drawn, and a power balance between the pumps and the turbine are calculated. The calculation shows a good power balance, which implies that the pump component tests, the turbine component test and the assembly test are reliably performed. At the starting period of the test, pressure rise-flow rate curve of a pump gradually approaches the ideal curve which could be obtained by very slow starting.