• 한국전기전자재료학회논문지
• /
• 제17권3호
• /
• pp.299-304
• /
• 2004

In recent years, silicon carbide has emerged as an important material for MEMS application. In order to fabricate an SiC film based MEMS structure by using chemical etching method, high operating temperature is required due to high chemical stability Therefore, dry etching using plasma is the best solution. SiC film was deposited by thermal CVD at the temperature of 100$0^{\circ}C$ and pressure of 10 torr. SiC was dry etched with a reactive ion etching (RIE) system, using SF$_{6}$/O$_2$ and CF$_4$/O$_2$ gas mixture. Etch rate has been investigated as a function of oxygen concentration in the gas mixture, rf power, working pressure and gas flow rate. Etch rate was measured by surface profiler and FE-SEM. SF$_{6}$/O$_2$ gas mixture showed higher etch rate than CF$_4$/O$_2$ gas mixture. Maximum etch rate appeared at RF Power of 450W. $O_2$ dilute mixtures resulted in an increasing of etch rate up to 40％, and the superior anisotropic cross section was observe

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1992년도 하계학술대회 논문집 B
• /
• pp.809-812
• /
• 1992

Charateristics of the ECR etch were Investigated about $MoSi_2$ layer which is widely used for the capping layer and barrier layer in VLSI metallization. The etch rate was evaluated according to gas ratio of $SF_6/BCl_3$, $N_2$ flow rate, RF power and chamber pressure. The chamber pressure, the most important factor, represented the maximum etch rate at about the pressure of 10 mTorr.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2010년도 하계학술대회 논문집
• /
• pp.175-175
• /
• 2010

The etching characteristics with etch rate of ITO thin films in an $O_2/BCl_3$/Ar plasma were investigated. The etch rate of ITO thin films increased with increasing $O_2$ content from 0 to 10 % in $BCl_3$/Ar plasma, whereas that of ITO decreased with increasing $O_2$ content from 10 % to 30 % in $BCl_3$/Ar plasma. The maximum etch rate of 65.9 nm/min for the ITO thin films was obtained at 10 % $O_2$ addition. The etch conditions were the RF power of 500 W, bias power of 200 W, and process pressure of 2 Pa. The analysis of x-ray photoelectron spectroscopy (XPS) was carried out to investigate the chemical reactions between the surfaces of ITO thin films and etch species.

• 한국전기전자재료학회논문지
• /
• 제15권2호
• /
• pp.105-109
• /
• 2002

The wet etching characteristics of magnetic materials such as NiFe and CoFe were investigated in terms of etch rate and etch profile by using variouus etching solutions (etchants). Among the various etching solutions, HNO$_3$, HCl, and H$_2$SO$_4$were selected for the etching of magnetic materials and showed distinct results. In the case of NiFe films, faster etch rate were obtained with HNO$_3$solution. When NiFe films ere etched with HCl solution, white etch residues were found on the surface of etched films. From FEAES analysis of these etch residues, they were proved to be by-product from the reaction of NiFe with Cl element. CoFe thin films showed the similar trend to the case of NiFe films. They were etched fast in HNO$_3$ solution while Chl solution represented slow etching. The etch profiles of CoFe films showed smooth etch profile but revealed the partial etching around the patterns in HNO$_3$solution of relatively high concentration. It was observed that the etched surface was clean and smooth, and that white etch residues were also remained on the etched films.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2000년도 춘계학술대회 논문집 전자세라믹스 센서 및 박막재료 반도체재료 일렉트렛트 및 응용기술
• /
• pp.112-116
• /
• 2000

This paper presents anisotropic ethcing characteristics of single-crystal silicon in tetramethylammonium hydroxide(TMAH):isopropyl alcohol(IPA) solutions containing pyrazine. With the addition of IPA to TMAH solutions, etching characteristics are exhibited that indicate an improvement in flatness on the etching front and a reduction in undercutting, but the etch rate on (100) silicon is decreased. The (100) silicon etch rate is improved by the addition of pyrazine. An etch rate on (100) silicon of $0.8\;{\mu}m/min$, which is faster by 13 % than a 20 wt.% solution of pure TMAH, is obtained using 20 wt.% TMAH:0.5 g/100 ml pyrazine solutions, but the etch rate on (100) silicon is decreased if more pyrazine is added. With the addition of pyrazine to a 25 wt.% TMAH solution, variations in flatness on the etching front were not observed and the undercutting ratio was reduced by 30 ~ 50 %.

• 한국전기전자재료학회논문지
• /
• 제15권3호
• /
• pp.227-232
• /
• 2002

The silylated photoresist etch process was tested by enhanced-ICP. The comparison of the two process results of micro pattern etching with $0.35\mu\textrm{m}$ CD by E-ICP and ICP reveals that I-ICP has bettor quality than ICP. The etch rate and the RIE lag effect was improved in E-ICP. Especially, the problem of the lateral etch was improved in E-ICP.

• 한국표면공학회지
• /
• 제41권6호
• /
• pp.269-273
• /
• 2008

The etch of $(Na_{0.5}K_{0.5})NbO_3$ (NKN) thin film was performed in $BCl_3/Cl_2/Ar$ inductively coupled plasma. It was found that the 1sccm addition $BCl_3$ (5%) into $Cl_2/Ar$ plasma caused a non-monotonic behavior of the NKN etch rate. The maximum etch rate of NKN was 95.3 nm/min at $BCl_3$ (1 sccm)/$Cl_2$ (16 sccm)/Ar (4 sccm), 800 W ICP power, 1 Pa pressure and 400 W bias power. The NKN etch rate shows a monotonic behavior a s the bias power increases. The analysis of the narrow scan spectra of XPS for both a s-deposited and etched NKN films allowed one to assume ion assisted etch mechanism. The most probable reason for the maximum etch rate can be defined as a concurrence of chemical and physical etch pathways.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2003년도 하계학술대회 논문집 Vol.4 No.2
• /
• pp.868-871
• /
• 2003

In recent years, silicon carbide has emerged as an important material for MEMS application. In order to fabricate an SiC film based MEMS structure by using chemical etching method, high operating temperature is required due to high chemical stability. Therefore, dry etching using plasma is the best solution. SiC film was deposited by thermal CVD at the temperature of $1000^{\circ}C$ and pressure of 10 torr. SiC was dry etched with a reactive ion etching (RIE) system, using $SF_6/O_2$ and $CF_4/O_2$ gas mixture. Etch rate have been investigated as a function of oxygen concentration in the gas mixture, RF power, and working pressure. Etch rate was measured by surface profiler and FE-SEM. $SF_6/O_2$ gas mixture has been shown high etch rate than $CF_4/O_2$ gas mixture. Maximum etch rate appeared at 450W of RF power. $O_2$ dilute mixtures resulted in an increasing of etch rate up to 40%, and the superior anisotropic cross section was observed.

• 한국세라믹학회지
• /
• 제53권6호
• /
• pp.700-706
• /
• 2016

Etch rate, surface roughness and microstructure as plasma resistance were evaluated for six kinds of oxide glass with different compositions. Borosilicate glass (BS) was found to be etched at the highest etch rate and zinc aluminum phosphate glass (ZAP) showed a relatively lower etch rate than borosilicate. On the other hand, the etching rate of calcium aluminosilicate glass (CAS) was measured to be similar to that of sintered alumina while yttrium aluminosilicate glass (YAS) showed the lowest etch rate. Such different etch rates by mixture plasma as a function of glass compositions was dependent on whether or not fluoride compounds were formed on glass and sublimated in high vacuum. Especially, in view that $CaF_2$ and $YF_3$ with high sublimation points were formed on the surface of CAS and YAS glasses, both CAS and YAS glasses were considered to be a good candidate for protective coating materials on the damaged polycrystalline ceramics parts in semi-conductor and display processes.

• Journal of Magnetics
• /
• 제20권4호
• /
• pp.366-370
• /
• 2015

New ion beam etcher (IBE) using a magnetized inductively coupled plasma (M-ICP) has been developed. The magnetic flux density distributions inside the upper chamber, where the plasma is generated by inductive coupling, were successfully optimized by arranging a pair of circular coils very carefully. More importantly, the proposed M-ICP IBE exhibits higher etch rate than ICP.