• Journal of Engineering Education Research
• /
• v.23 no.3
• /
• pp.32-40
• /
• 2020

A new moment of inertia experiment apparatus different from the existing one has been developed, which does not require deformation of a sample in order to fix it to the apparatus. This new experiment apparatus was able to experiment with constant-shaped objects that did not deform the samples, so that it enabled them for conducting an experiment which is close to an ideal rigid model dealt in the general physics course. The new experimental apparatus was easy and accurate in measuring the physical quantity by using the experimental principle of physical pendulum. In the results of the measurement of the moments of inertia of the six samples, all measurements were made to be accurate enough to measure with very small errors within 1%. In addition, it has been found to be useful as an experiment apparatus to understand the concept of the moment of inertia and to prove the formula for moment of inertia. Therefore, if the new moment of inertia experiment apparatus developed in this study is used in students' experiments, it is expected that students will be able to greatly increase their understanding of the concept of moment of inertia.

• Journal of Applied Biological Chemistry
• /
• v.53 no.4
• /
• pp.248-252
• /
• 2010

This study presented a development of a phototactic apparatus for pest monitoring. We carried out behavioral experiment against various pest species by using the phototactic chamber. Consequently, the phototactic apparatus was confirmed suitable result of behavioral experiment. Therefore, we believed that the test apparatus help to understand the phototactic responses of various pests.

• Journal of The Korean Association For Science Education
• /
• v.36 no.3
• /
• pp.423-434
• /
• 2016

The purpose of this study is to investigate preservice earth science teachers' mental models through applications of Coriolis force experiment apparatus. After the root of preconception was examined by face to face interviews based on the questionnaire, five preservice earth science teachers were finally selected for this study. The mental models about concept of Coriolis force was classified into naive mental model, static unstable mental model, dynamic unstable mental model, and scientific mental model through the result of individual interviews and their drawings. According to the mental model analysis about Coriolis' force conception, students C and M showed naive mental model about concept of Coriolis force before experiment. After the experiment, student M's model changed to static unstable mental model. Student C's model improved to dynamic unstable mental model. In adiition, students D and O's model improved from static unstable mental model to dynamic unstable mental model. In the case of student B, the dynamic unstable mental model was maintained after the experiment, however, student B's preconception changed to scientific concept. It turned out that a change occurred from low mental model level to integrated mental model after the application of the developed Coriolis' force experiment apparatus. According to the results, national curriculum is similar to static unstable mental model and the result of developed Coriolis' force experiment apparatus is similar to dynamic unstable mental model. It is suggested that it become the theoretical foundation to develop more comfortable and advanced Coriolis force experiment apparatus by improving the experiment apparatus.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.17 no.5
• /
• pp.107-115
• /
• 2008

In this research, it has been developed the tongs mechanism by a friction force for curbstone working. This tongs apparatus was farmed to grip and rotate the rectangular curbstone. Specification of this tongs apparatus has been determined by considering a loading weight and reversal load preventing reversal of 1.5 ton excavator. And, specification of the linear actuator has been determined with considering mechanical structure and the operation power demanded by the grip pad friction of tongs apparatus. The safety of the part has been examined from the 3D numerical simulation of the tongs apparatus. The operation system has been arranged to grip and rotate curbstone by on-off switching. The prototype has been established to carry out experiment after installing 1.5 ton excavator.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.17 no.1
• /
• pp.3655-3665
• /
• 1975

This study was intended to develop a method for measuring the grain separating performance of threshers. The grain separating apparatus used for the experiment was designed and constructed, the function of which was to separate pneumatically mature and immature grain, chaff, straw, dust, and other impurities from the products of threshing. The apparatus has five material outlets where grains and impurities are fallen down by separation depending upon the specific gravity of the material white it moves above the outlets. The principle of design was to separate the mixture of mature grain, immature grain and chaff as distinct as possible, and to induce the mature grains onto the first outlet, the immature grains onto the second and the third, and the straw wastes onto the forth and the fifth outlets. The developed apparatus was tested to evaluate its separating performance with two rice varieties (Tongil and Mine-hikari) at different moisture levels and air velocities. The optimum conditions for operating the apparatus were found from experiment. The results are summarized as follows; 1. The degrees of separation, especially the amount of immature grain contained in the mature paddy, were dependent upon air speed delivered. The optimum air velocities for this apparatus for each levels of grain moisture contents were found from a series of experiments as follows; 14.7-15.3m/sec. for grain of 16 percent moisture content in wet basis, 15.3-16.0m/sec. for 20 percent, and 16.0-16.4m/sec for 24 percent. 2. Composition ratios determined based on the brine separating method was fairly well acted upon the developed apparatus, indicating its recollecting rate of the mature grains as 97.6 to 99.9 percent. The developed separatus acted similarly upon the two rice varieties which had different composition of immature paddy grain. In other words, the separating performance by the apparatus had a good correlation with the one by the brine separating method. 3. As immature grains were separated out unsatisfactory in these experiments than the brine separating method, further investigation may be needed to improve a separating performance of these materials. But the results obtained suggested a possibility of using the tester to replace the current hand separating method, ther eby enabling more consistent test results and also eliminating nearly all costly hand seperating operations.

• Journal of the Korean Vacuum Society
• /
• v.8 no.4B
• /
• pp.530-535
• /
• 1999

W made a near-field optical microscope(NSOM) apparatus and evaluated it. To control the distance between a tip and a sample, we used a piezoelectric translator and a He-Ne laser, and consequently obtained the spatial resolution better than 100nm. For the semiconductor spectroscopic applications, we performed photoluminescence and photocurrent experiments on the GaAs/AlGaAs MQWs samples. In the case of PL experiment, we obtained the low signal to nose ration due to the extremely small power of a light source passing through the nanometric optical fiber tip. However photocurrent experiment shows a hundred times better signal to noise than that of PL experiment. This suggests that photocurrent experiment using NSOM have the possibility to provide the spatial resolution better than 10nm.

• Proceedings of the KIEE Conference
• /
• 1990.11a
• /
• pp.63-67
• /
• 1990

An axial flux magnet for a magnetic levitation system is designed and analysed by finite element simulations. The results are compared with those of experiment in order to verify the analysing method. Lift force, air gap flux density and temperature characteristics of the magnet showed fairly good agreement with each other.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2003.11a
• /
• pp.892-897
• /
• 2003

This study deals with the performance of a simplified test apparatus for measurement of sound insulation of panels. In order to investigate its performance, results from experiment and theory of the sound transmission loss for single and double panels are compared. Comparative results show that in evaluation of the sound insulation performance, the test apparatus has a cumbersome problem at the low frequency region, i.e. below 315 ㎐, presumably because of the poor diffuse sound field in the chambers. Meanwhile at the high frequency, it shows a considerable results comparable to the theoretical prediction. One of the objective of this study that compares measured results between a real reverberation chamber and a simplified test apparatus, by using a specimen of a sandwich panel. It shows qualitatively resonable agreement from which one can find a potential to provide a design tool.

• Journal of The Korean Association For Science Education
• /
• v.21 no.3
• /
• pp.547-557
• /
• 2001

In this study, we compared the contents of cloud making experiments in middle school science textbooks of 5th and 6th science curriculum from the viewpoint of methods and apparatus. And we analyzed the problems of the experimental methods and apparatus based on the thermodynamic theories. A new experiment was developed to solve the problems, and the effects of new experiment were compared with those of the experiments in the textbooks.

• Transactions of Materials Processing
• /
• v.4 no.4
• /
• pp.335-344
• /
• 1995

In this paper, an experimental study of a hot forging process is carried out using plasticine and the die set manufactured with the aid of rapid prototyping. In order to manufacture the die set, Stereolithography Apparatus(SLA) which is most widely used rapid prototyping system is introduced. Turbine blade forging is performed using palsticine and the SLA prototype die set. Through the experiment, it has been shown that SLA prototype is suitable to the die set for the plasticine workpiece, and the formability and the forming load of turbine blade forging are predicted.