• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 2001년도 봄 학술발표회 논문집
• /
• pp.95-101
• /
• 2001

Steel bridges, which have been damaged by load and corrosion, need repair or strengthening. In general, before the repair welding procedure, cutting procedure carry out. Therefore, the investigating of the behavior of stress generated by cutting is so important for safety of structure. Residual stress produced by gas cutting was analyzed using 2D and 3D thermal elasto-plastic FEM. According to the results, the magnitude of temperature was analyzed by 2D-FEM is smaller than that was analyzed using the 3D-FEM program at the start and end edge of flange. And the magnitude and distribution of residual stress of perpendicular to the cutting line was analyzed by the 2D-FEM program was similar to that was analyzed by the 3B-FEM program. Therefore, it is possible to predict of cutting stress by 2D and 3D FEM.

• 한국정밀공학회지
• /
• 제29권10호
• /
• pp.1043-1049
• /
• 2012

The FEM analysis of machine tools is the general analysis process to evaluate machine performance in the industry for a long time. Despite advances in FEM software, because of difficult simplicity of CAD drawing, little experience of joints stiffness modeling and troublesome manual contact area divide for bindings, the industry designers think the FEM analysis is still an area of FEM analysis expert. In this paper, the automation of modeling process with simplicity of drawing, modeling of joints and contact area divide is aimed at easy FEM analysis to enlarge utilization of a virtual machine tools. In order to verify the effects of modeling automation, a slant bed type model with tilting table is analyzed. The results show FEM modeling automation method only needed 45 minutes to complete the whole modeling process, while manual modeling method requires almost one month with 8200 calculations for coordinate transformations and stiffness data input.

• 한국지반신소재학회논문집
• /
• 제8권1호
• /
• pp.11-18
• /
• 2009

본 논문에서는 보강토사면 안정해석에 있어서 한계 평형법과 강도감소법에 의한 유한요소법의 비교분석결과를 나타내었다. 현재 보강토 옹벽 해석에 적용하는 방법은 한계평형해석법이다. 강도감소법에 의한 유한요소법은 연속체 역학 기반을 두고, 흙의 강도정수를 안전율로 나누어 감소시켜, 수렴되지 않는 시점을 사면의 파괴로 간주하는 방법이다. 본 연구에서는 보강토옹벽사면의 안전율과 파괴활동면에 대하여 비교검토를 하였다. $60^{\circ}$ 보강토 사면에 대하여 LEM과 SSR-FEM 방법에 의한 안정성해석결과에 대하여 비교검토하였다. 두 해석에 의한 비교 검토결과 보강토 옹벽의 안정성 해석에 대하여 SSR-FEM의 유효성이 조사되었다.

• 한국전자통신학회논문지
• /
• 제18권5호
• /
• pp.835-840
• /
• 2023

2D FEM은 3D FEM에 비하여 모델 및 조건을 간소화하여 해석할 수 있다. 하지만 코일의 조건에 대하여는 실제 코일의 인입과 반출을 순차적으로 구성하여 해석 조건에 입력하는 경우가 많다. 본 논문은 다수의 슬롯을 가지더라도 하나의 FEM Coil로 구성한 등가 권선법을 적용하여 코일 조건의 단순화 및 해석 시간의 단축을 나타내고 권선형 마그네틱 기어에 적용하여 결과의 일치성을 보인다.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제49권1호
• /
• pp.52-58
• /
• 2000

Signal propagation in nonlinear optical fiber is analyzed numerically by using SS-FEM (Split-Step Finite Element Method). By adopting cubic element function in FEM, soliton equation of which exact solution was well known, has been solved. Also, accuracy of numerical results and computing times are compared with those of Fourier method, and we have found that solution obtained from using FEM was very relatively accurate. Especially, to reduce CPU time in matrix computation in each step, the matrix imposed by the boundary condition is approximated as a sparse matrix. As a result, computation time was shortened even with the same or better accuracy when compared to those of the conventional FEM and Fourier method.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 추계학술대회
• /
• pp.1870-1875
• /
• 2003

Optimization has been used in many engineering problems and must be one of the essential components during design process now. It is the process of maximizing the performance called an objective function of a system while satisfying some constraints, so finite element method is generally required in order to obtain these values during optimization. However, there are some difficulties to obtain them by means of FEM, where the changes of design variables cause the distortion and the regeneration of mesh that may result in inaccuracy and inefficiency. In order to overcome this problem, this paper proposed an alternative that the eXtended FEM introduced and developed by Ted Belytschko was applied to the optimization process because the key points of the X-FEM lie in that the discontinuity can be represented independently on the mesh by a function called in an enrichment function.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 2011년도 정기 학술대회
• /
• pp.697-700
• /
• 2011

본 논문에서는 X-FEM을 사용하여 혼합모드 하중 상태에서의 이차원 선형탄성체의 균열문제에 대한 형상 설계민감도 해석을 수행하였다. X-FEM이란 균열과 같은 특수한 해를 근사하는 방법으로써, 확장함수를 도입하여 FEM의 한계를 극복하는 방법론이다. X-FEM 하에서 해를 근사하는 데 쓰이는 확장함수들은 불연속성과 특이성을 포함하고 있어 물리적 영역에 의존한다. 이는 설계민감도 해석을 수행하는 과정에서 그러한 의존성을 고려해주는 것이 필요하다. 따라서 본 논문에서는 X-FEM 기반의 형상 설계민감도 해석해를 제안하고자 한다. 식의 유도는 전 미분 공식에 기초하고 있으며, 형상함수의 설계변분에 대한 의존성에 관한 항을 추가시켰다. 또한, 균열 주위의 국부적인 공간에서의 확장된 자유도에 설계속도를 가한다. 이에 대한 몇 가지 수치 예제를 통하여 개발된 방법론의 타당성을 확인하였다.

• 한국기계가공학회지
• /
• 제9권1호
• /
• pp.87-92
• /
• 2010

Micromachining technology using a ultra-precision micromachining system is widely applied in the fields of optics, biotechnology and analytical chemistry, etc. specially in microfabrication of fresnel lens, light guide panels of TFT-LED and PDP ribs with micro-patterns, machining errors have an effect on the performance of those products. The deflection of tool and tool holder is known to be one of the very important factors that is due to machining errors in micromachining. The deflections of diamond tool and tool holder used in micro-grooving are analysed by FEM. We analysed by FEM. With an linearity valuation of FEM, deflection of tool and tool holder is calculated by using the data of cutting force which is acquired from micro-V groove machining experiments in micromachining system.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제54권2호
• /
• pp.60-65
• /
• 2005

This study tries to analyzes the static friction torque that generated in a micro-electromagnetic clutch by using FEM. For the purpose of design change and optimization of the micro-electromagnetic clutch, the static friction torque prediction is very important. We construct the axi symmetric FEM model for analyze the static friction torque and the real material properties are substituted to the FEM model. For a test, predicted static friction torque is compared with experimental one to discuss the rationality of torque analysis process. The analytical result agrees well to experimental data. explaining the validity of the mathematical process and FEM model.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2002년도 추계학술대회논문초록집
• /
• pp.401.2-401
• /
• 2002

An unconstrained tuning fork with a 3-D model has been numerically analyzed by Finite Element Method (FEM) and Boundary Element Method (BEM). The first three natural frequencies were calculated by the FEM modal analysis. Then the change of the modal frequencies was examined with the variation of the tuning fork length and width. (omitted)