• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.14 no.8
• /
• pp.1752-1758
• /
• 2010

A FM-CW radar is used for the various purposes as a remote sensing device since it has the advantages of the relatively simple implementation and the low probability of signal interception. A FM-CW radar uses the same frequency modulated continuous wave for both transmission and demodulation. Therefore, the received beat frequency represents the range and Doppler information of targets. However, using the conventional FFT method, the degree of accuracy and resolution in the spectrum estimation can be seriously degraded in the detection and tracking of fast moving targets because of the short dwell time. Therefore, in this paper, the model parameter estimation methods called as an autoregressive method is applied to overcome these problems and showed that the improved accuracy and resolution can be obtained for the target range and velocity estimation.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.10 no.7
• /
• pp.1104-1110
• /
• 1999

When a FM-CW radar is used to measure the target distance, the nonlinearity relationship between the VCO control voltage and the output frequency makes an adverse effect on the measurement accuracy. Recently, many nonlinearity correction schemes using signal processing techniques and dedicated hardwares have been studied. This paper presents a signal processing technique to compensate for the VCO nonlinearity using a reference signal. To demonstrate the validity of the presented technique, several experiments were conducted and the results show reduction of the distortion in the range profile and the resolution improvement.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.15 no.9
• /
• pp.1840-1846
• /
• 2011

It is necessary to estimate the Doppler spectrum for each range cell for the extraction of useful information from the return echoes in radar systems used for the remote sensing purpose such as detection of moving targets and weather surveillance. The signal amplitude in the beat frequency band is the important parameter in the detection and tracking of targets. However, strong clutter echoes do exist in most radar operation environments and the system phase noise spreads both the clutter and signal echoes of the target. In this paper, the effects of this system phase noise are analyzed concerning the clutter and the signal beat spectrum. It is shown that the separation capability of adjacent beat signal depends on the degree of spread in the clutter and beat signal caused by the radar system phase noise

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.16 no.9
• /
• pp.1856-1863
• /
• 2012

Two separate antennas are usually adopted in high performance radar systems to achieve the high degree of isolation since the transmission and reception of signals cannot be separated in time. However, even though two spatially separated antennas are installed in the system, strong signals from a transmission antenna can cause the serious interference problem in a receiving antenna. These strong interference signals from the transmission antenna can cause serious problems in detection and analysis of much weaker echo signals which are reflected by small targets. Also the increased level of background noise power due to interference can cause the serious degradation of the system performance. Therefore, in this paper, the proper cancellation method is suggested and results are shown and analyzed for removal of strong interference and background noise power.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2009.10a
• /
• pp.758-761
• /
• 2009

It is necessary to estimate the Doppler spectrum for each range cell for the extraction of useful information from the return echoes in radar systems used for the remote sending purpose such as detection of moving targets and weather surveillance. The signal amplitude in the given frequency band is the important parameter in the detection and tracking of targets. However, the system performance can be seriously degraded if the efficient removal of the strong clutter is not possible. If the phase noise spreads both the signal and clutter, the clutter removal can be very difficult and the accuracy of frequency estimates is also deteriorated. Therefore, in this paper, the effects of phase noise are analyzed in the estimation of beat frequencies.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2011.05a
• /
• pp.50-51
• /
• 2011

In a radar system using a continuous waveform, the separated antennas are needed for transmission and reception to increase the sensitivity of the receiver channel. Even for these separated antennas, the serious intereference in the weak echo signal can occur due to the relatively strong power of the transmitted waveform. Therefore, in this paper, the effects of this leakage interference on the receiving signal are analyzed according to the degree of antenna isolation.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.38 no.4
• /
• pp.38-44
• /
• 2001

In this paper, for the microwave level meter based on the FM-CW radar, we analyze the spectrum correlation of beat signals and propose a measurement algorithm using the theory. For industrial applications, level meters must have high precision, which requires a good linearity of VCO. But, in practice, it is very complicated or very expensive to make VCO linear enough to be acceptable in the industrial field. We propose a measurement algorithm using the fact that there exists a peak in the spectrum correlation of beat signals when range difference is sufficiently small. This makes it possible to determine the range difference in a precise manner even using a practical VCO. We present some experimental results to show the validity of this algorithm.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• v.1
• /
• pp.291-296
• /
• 2006

The restrictions concerning the use of the radio waves have become severe, the marine radar with low spurious is being developed. Therefore, it is necessary to develop aids to navigation as a radar beacon can respond to new type of marine radar. Because the system of radar in the future is an indetermination, new radar beacon should correspond to old and new radar system during a transition period. New radar beacon that is also able to respond to pulse radar, pulse compression radar and FM-CW radar were considered in these years in Japan. The sign of the response of Morse code in a new system is generated by the delay synthesis system. Computer simulation and actual examination using trial circuit were curried out. A big possibility was set up in the development of the new radar beacon that was able to correspond to old and new radar system. These results and the state of new radar beacon is mentioned in this paper.

• Proceedings of the IEEK Conference
• /
• 1998.10a
• /
• pp.331-334
• /
• 1998

In this paper, we have presented an improved design of the microwave level meter based on the principle of FM-CW radar. First, we have analyzed the effect of VCO nonlinearity on the spectral broadening of the beat signal, and presented a new type of design theory to linearize VCO tuning curve adopting FFT algorithm. Simulation results for a VCO having the linearity of 25% have been presented, which show the usefulness of the design algorithm.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.11 no.1
• /
• pp.18-25
• /
• 2000

In this paper, we have designed a microwave level meter based on the FM-CW radar theory using a YIG-tuned oscillator (YTO). YTO has an excellent frequency linearity, so a linearizer circuit is not necessary for the level meter. It is shown that interference signals reflected from nearby obstacles can be removed by using a digital band-pass filter. An FIR band-pass filter is designed using the Kaiser window. The distance measurement has been performed in the outdoor test field. The measurement data have been obtained for the range of 1~40m with 1m step, and the results show that the standard deviation of the measured data is 2.33 cm. The level meter manufactured in this study can be applied usefully in the industrial facilities which are not accessible easily, for example, to measure the level of molten metal in the iron and steel company.