• 펄프종이기술
• /
• 제45권1호
• /
• pp.59-66
• /
• 2013

Fillers have been used for printing paper to improve printability, sheet formation and optical properties and to reduce production costs by replacing expensive wood pulps. However, an increased filler content will decrease paper strength because filler particles interfere with fiber-fiber bonding. In order to increase filler content without sacrificing too much paper strength in high filler content papers, the surface of precipitated calcium carbonate (PCC) has been modified by adsorbing anionic polyacrylamide and cationic starch in series. The adsorbed polymer layers would enhance interactions between the filler surface and the fiber surface, improving internal bonding. It was found that the modified PCC increased paper strength at a given filler content compared to the coventional method. Negligible differences in optical properties and formation of paper, filler and fines retention and drainage on the wire section were observed between the modified and the conventional PCC. However, the decreased bulk of paper was observed when the modified PCC was used.

• Journal of Welding and Joining
• /
• 제22권1호
• /
• pp.71-76
• /
• 2004

In the standpoint of the arc pressure, the effects of the filler wire feed rate on the penetration was investigated in this study. The pure Ar gas was used as a shield gas and the parameters investigated were the welding current and the filler wire feed rate. By making the experiment on the arc pressure, we could know that the arc pressure was fluctuated as the depth-into-arc of the tungsten rod. Instead of the filler wire, the tungsten rod was supplied into the molten pool to make this experiment. Because the filler wire melted in arc and then we couldn't measure the arc pressure. So, the tungsten rod - the highest melting point - was used. According to the depth-into-arc of the tungsten rod, the arc pressure could be measured by using the manometer. It was proved that the arc pressure got higher as the wire feed rate was slow. It is reported the arc pressure is proportion to welding voltage and the square of welding current. But, in the filler wire TIG welding, we could blow that arc pressure was fluctuated as the depth-into-arc of filler wire was changed. We could measure the arc pressure by the variation of the filler wire feed rate and could verify that it affected bead shape and penetration.

• 전자공학회논문지 IE
• /
• 제43권4호
• /
• pp.122-127
• /
• 2006

무전해 도금법을 이용하여 고분자섬유의 형태를 가진 전도성 필러를 제조하였다. 나일론 6과 레이온 섬유 분체에 니켈과 구리를 도금한 복합 전도성 필러를 제조하였다. 입도 분석기를 이용하여 필러의 입자크기분포를 측정하였으며, 전도성 필러의 전도성을 측정하기 위해 전도성 분석기를 이용하였으며, 본 연구의 전도성 필러와 유사한 용도로 사용되는 탄소섬유의 전도성을 측정하여 전도성의 차이점을 비교하였다. ABS 수지에 제조된 전도성 필러를 주입하여 필름을 만들어서 1MHz$\sim$1GHz 주파수 대역에서 전자파 차폐 특성을 측정하였다. 제조된 전도성 필러가 첨가된 필름의 전자기파 차폐 특성을 측정하기 위하여 ASTM(D4935-89) 규격의 플랜지형 동축전송선 측정기구를 사용하였다. 제조된 전도성 필러는 기존의 탄소계 필러에 비해 전도성이 커서 전자파 차폐용 재료로 적합하였다.

• 한국세라믹학회지
• /
• 제42권2호
• /
• pp.110-116
• /
• 2005

본 연구는 $BaO-B_{2}O_3-ZnO$계에서 저온소성이 가능한 조성을 탐색하고, 여기에 $Al_{2}O_3$를 filler로 첨가하여 복합체를 제조할 경우의 소결거동과 물성에 미치는 영향을 조사하였다. 이때 첨가하는 알루미나 분체는 입자크기가 서로 다른 두 종류를 이용함으로서 알루미나 입자 크기의 효과도 동시에 조사하였다. 알루미나 첨가량이 증가하는 경우 복합체의 치밀화정도, 유전상수, 열팽창계수, 그리고 경도 값이 감소하였다. 또한 첨가되는 알루미나 입자의 크기가 미세할 경우 그 감소율은 증가되었다. 한편 파괴인성값은 알루비나 첨가량이 많을수록, 알루미나 입자 크기가 작을수록 오히려 증가하였는데 이는 기공과 filler의 crack전파 억제 효과에 의한 것으로 해석하였다.

• Nuclear Engineering and Technology
• /
• 제48권6호
• /
• pp.1396-1403
• /
• 2016

In this study, fast-curing shielding materials were prepared with a two-component polyurethane matrix and a filler material of PbO through a one-step, laboratory-scale method. With an increase in the filler content, viscosity increased. However, the two components showed a small difference. Curing time decreased as the filler content increased. The minimum tack-free time of 27 s was obtained at a filler content of 70 wt%. Tensile strength and compressive strength initially increased and then decreased as the filler content increased. Even when the filler content reached 60 wt%, mechanical properties were still greater than those of the matrix. Cohesional strength decreased as the filler content increased. However, cohesional strength was still greater than 100 kPa at a filler content of 60 wt%. The ${\gamma}$-ray-shielding properties increased with the increase in the filler content, and composite thickness could be increased to improve the shielding performance when the energy of ${\gamma}$-rays was high. When the filler content was 60 wt%, the composite showed excellent comprehensive properties.

• 동력기계공학회지
• /
• 제9권2호
• /
• pp.93-98
• /
• 2005

The performance of cooling tower is dependent on the thermal performance of the packings. It's assessed by heat transfer rate and fan power. In this study, new packing was developed for application in compact type cross-flow cooling tower. The packing characteristic curve and the pressure drop curve were obtained by measuring packing characteristic values and pressure drops of small sized filler in comparison to existing mid-large sized filler. The heat transfer characteristics on small sized filler are about 66% higher than existing mid-large sized filler. The pressure drop characteristics on small sized filler are about two times of the pressure drop characteristics on existing mid-large sized filler.

• Carbon letters
• /
• 제14권2호
• /
• pp.105-109
• /
• 2013

Effects of the amount of nickel powder (Ni) in Ni-carbon fiber (CF) hybrid filler systems on the conductivity(or resistivity) and thermal coefficient of resistance (TCR) of filled high density polyethylene were studied. Increases of the resistivity and TCR with increasing Ni concentration at a given hybrid filler content were observed. Using the fiber contact model, we showed that the main role of Ni in the hybrid filler system is to decrease the interfiber contact resistance when Ni concentration is less than the threshold point. The formation of structural defects leading to reduced reinforcing effect resulted in both a reduction of strength and an increase of the coefficient of thermal expansion in the composite film; these changes are responsible for the increases of both resistivity and TCR with increasing Ni concentration in the hybrid filler system.

• Macromolecular Research
• /
• 제11권6호
• /
• pp.506-510
• /
• 2003

A Zn ion-coated nanosilica filler has been developed and tested, in chlorosulfonated polyethylene (CSPE) and polychloroprene (CR), as a vulcanizing activator, cum was reinforcing filler. In this study, ZnO was replaced by the Zn ion-coated nanosilica filler with an aim of studying the dual role of this nanofiller in CSPE and CR. In the case of CSPE vulcanizates, the presence of MgO deteriorated the state and rate of cure when the Zn ion-coated nanosilica filler was used, but in the case of CR it improved the state of cure and enhanced the modulus and tensile strength. The Zn ion-coated filler proved to be a better reinforcing-cum-curing agent than was externally added ZnO and NA-22 also proved to be a better curative in the presence of the Zn ion-coated nanosilica filler for both CSPE and CR.

• 한국분말재료학회지
• /
• 제6권4호
• /
• pp.320-324
• /
• 1999

The formation, microstructure and properties of novel ceramic composite materials manufactured by active-filler-controlled polymer pyrolysis were investigated. In the presence of active filler particles such as transition metals, bulk components of various geometry could be fabricated from siliconorganic polymer. Molybdenum- and tungsten-filled polymer suspensions were prepared and their conversion to ceramic composites by annealing in $CH_4$ atmosphere were studied. Dimensional change. porosity and phase distribution (filler network) were analyzed and correlated to the resulting hardness values. Molybdenum and tungsten as active filler were carburized completely to $Mo_2C$, $W_2C$ and WC in $CH_4$ atmosphere. Consequently, microcrystalline composites with the filler reaction products embedded in a silicon oxycarbide glass matrix were formed. Hardness was increased with increasing carburization and reached 8.6-9.5 GPa in the specimen pyrolyzed in $CH_4$ atmosphere.

• Journal of Mechanical Science and Technology
• /
• 제20권11호
• /
• pp.1891-1897
• /
• 2006

In this study, a new model to predict the effective elastic constants of composites with spherical fillers is proposed. The original Eshelby model is extended to a finite filler volume fraction without using Mori-Tanaka's mean field approach. When single filler is embedded in the matrix, the effective elastic constants of the composite are computed. The composite is in turn considered as a new matrix, where new single filler is again embedded in the matrix. The predicted results by the present model with a series of embedding procedures are compared with those by Mori-Tanaka, self-consistent, and generalized self-consistent models. It is revealed through parametric studies such as stiffness ratio of the filler to the matrix and filler volume fraction that the present model gives more accurate predictions than Mori-Tanaka model without using the complicated numerical scheme used in self-consistent and generalized self-consistent models.