• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2000년도 춘계학술발표대회 논문집
• /
• pp.215-217
• /
• 2000

• International Journal of Ocean System Engineering
• /
• 제2권4호
• /
• pp.209-213
• /
• 2012

Recently, the fuel using in the diesel engines of marine ships has been changed to a low quality of heavy oil because of the steady increase in the price of oil. Therefore, the wear and corrosion in all parts of the engine such as the cylinder liner, piston crown, and spindle and seat ring of exhaust valves has correspondingly increased. The repair welding of a piston crown is a unique method for prolonging its lifetime from an economic point of view. In this case, filler metals with a high corrosion and wear resistance are mainly being used for repair welding. However, often at a job site on a ship, a piston crown is actually welded with mild filler metals. Therefore, in this study, mild filler metals such as CSF350H, E8000B2, and 435 were welded to SS401 steel as the base metal, and the corrosion properties of the weld metals with and without post weld heat treatment were investigated using some electrochemical methods in a 0.1% $H_2SO_4$ solution. The weld metal welded with CSF350H filler metal exhibited the best corrosion resistance among these filler metals, irrespective of the heat treatment. However, the weld metal zones of the E8000B2 and 435 filler metals exhibited better and worse corrosion resistance with the heat treatment, respectively. As a result, it is suggested that in the case of repair welding with CSF350H and 435 filler metals, no heat treatment is advisable, while heat treatment is desirable if E8000B2filler metal is used with repair welding.

• Elastomers and Composites
• /
• 제46권2호
• /
• pp.138-143
• /
• 2011

EPDM에 카본블랙과 더불어 무기 충전제인 탈크, 탄산칼슘, 혹은 클레이를 함께 혼합하여 EPDM 배합물과 가황물을 제조하여, 무기 충전제가 EPDM 배합물과 가황물의 특성에 미치는 영향을 조사하였다. 무기 충전제를 추가해도 결합 고무 함량(bound rubber content)에는 큰 차이가 없었다. 무기 충전제 함량이 높을수록 큰 입자로 존재함을 확인하였다. 무기 충전제를 추가하면 가교 시간은 전반적으로 증가하는 경향을 보였으며, 델타 토크(delta torque)는 감소하였다. 무기 충전제를 추가하면 모듈러스는 전반적으로 감소하였으나, 신율과 인장강도 그리고 인열강도는 증가하였다. 모듈러스의 감소와 신율의 증가는 가교밀도의 감소로 설명하였으며, 인장강도와 인열강도의 증가는 신율의 증가로 설명하였다. 무기 충전제의 첨가에 의해 보강성은 증가하지 않았고 가교밀도는 감소하였다.

• 한국통신학회논문지
• /
• 제30권6A호
• /
• pp.499-509
• /
• 2005

위성 DMB (Digital Multimedia Broadcasting) 시스템은 도심 환경에서 위성으로부터의 감쇄된 신호를 증폭하기 위하여 별도의 수신신호 증폭을 위한 지상 중계기(Gap-filler)를 필요로 한다. 따라서 Gap-filler를 통해 증폭된 신호는 위성으로부터 직접 수신된 신호에 비하여 위성 DMB 시스템 간에 보다 더 큰 간섭을 야기한다. Gap-filler를 통해 발생된 위성 DMB 시스템 간의 간섭에 의해 위성 DMB 시스템의 Outage Capacity가 제한될 수 있기 때문에, 위성 DMB 시스템 간의 상호간섭 효과를 최소화 하여야 각 시스템의 기대 Outage Capacity를 얻을 수 있다. 본 논문에서는 ITU-R BO. 1130-4를 토대로, 보다 정확한 파라미터를 사용한 시스템 레벨 시뮬레이션을 통해 위성 DMB 시스템간의 상호간섭을 분석하고, 각 시스템의 Gap-filer에서 설정한 Spectrum Mask를 이용하여 간섭을 최소화하고 Outage Capacity를 극대화하기 위한 Gap-filler를 이용하는 위성 DMB 시스템간의 보호대역 및 적정 셀 반경을 제안한다.

• 보존과학회지
• /
• 제26권4호
• /
• pp.361-370
• /
• 2010

Gameunsaji West Stone Pagoda;Filler;Consolidation;Pore;Injection;Materials; 석조문화재의 내부공극은 강화처리만으로 효과를 보기 어렵고 고분자합성수지를 이용한 충전의 경우 재료적 이질감과 높은 강도, 저점도에 따른 유동성 향상으로 내부벽면만 접착, 강화되는 단점이 있다. 따라서 본 연구는 무기질 바탕의 다양한 충전제를 검색하여 충전효과검증을 통해 감은사지삼층석탑 공극부 충전에 효과적인 충전제를 선정, 보존처리를 실시하였다. 충전실험 결과 부재와 동일하거나 매우 유사한 물성을 지닌 KSE 500 STE + KSE Filler A KSE Filler B 조합을 사용하여 충전하였다. 서탑 전체표면적은 $252.6m^2$이며 이중 내부공극이 발달한 부분은 $17.77m^2$(7.03%)로 내부를 충전($24,885m{\ell}$)하였다.

• Composites Research
• /
• 제35권6호
• /
• pp.431-438
• /
• 2022

전자 기기의 발달에 따라 발생하는 발열 문제를 해결하기 위해 높은 열전도도를 갖는 방열소재의 개발이 필요하다. 고분자 복합소재는 고분자의 장점과 열전도성 필러의 장점을 동시에 지녀 경량 방열소재로 각광받고 있다. 하지만, 산업적으로 요구되는 열전도도를 달성하기 위해서는 볼륨비로 60 이상의 고함량의 필러 충진이 요구되므로 최근에는 필러의 구조 제어를 통해 비교적 저함량의 필러 충진으로도 열 전달 경로를 최적화할 수 있는 연구들이 진행되고 있다. 본 리뷰에서는 고분자 복합소재 내 열전도성 이방성 필러의 구조를 제어해 비교적 적은 필러 함량으로 고열전도성 방열소재를 제작하는 다양한 전략을 소개하고자 한다.

• Journal of the Korean Wood Science and Technology
• /
• 제34권2호
• /
• pp.10-21
• /
• 2006

Recycled polypropylene (RPP) - Wood Saw Dust (WSD) composites with and without acetylation of filler were produced at different filler loading (15%, 25%, 35% and 45% w/w) and filler size (300, 212 and $100{\mu}m$). The RPP-WSD was compounded using a Haake Rheodrive 500 twin screw compounder at $190^{\circ}C$ at 8 MPa for 30 minutes. The mechanical properties and water absorption properties of modified and unmodified WSD-PP composites were investigated. Acetylation of WSD improved the mechanical and water absorption characteristic of composites. The decrease of filler size (300 to $100{\mu}m$) of the unmodified and acetylated WSD showed increase of tensile strength and impact properties. The composites exhibited higher tensile modulus properties as the filler loading increased (15% to 45%). However tensile strength, elongation at break and impact strength showed the opposite phenomenon. Water absorption increased as the mesh number and filler loading increased. With acetylation, lower moisture absorption was observed as compared to unmodified WSD. The failure mechanism from impact fracture of the filler-matrix interface with and without acetylation was analyzed using Scanning Electron Microscope (SEM).

• 대한치과기공학회지
• /
• 제36권3호
• /
• pp.165-169
• /
• 2014

Purpose: This study is a mechanical strength supplementation of denture base resin Polymethyl methacrylate (PMMA) is in general use for denture base resin of the partial and full denture, however, The polymerization process of PMMA is not stabilized. Because of compatibility problems, preceding studies were performed, which were enhancing mechanical strength(Camilo Machado 2007),(Ana M. 2008), addition filler to materials property(Ayse Mese, 2008), self curing method(Hiroshi Shimizu, 2008). Methods: The carbon fiber and polyacetal filler, reinforced the mechanical strength for improving the stability of denture base resin were supplemented to the self cured resin. The Modulus of elasticity and the restoring force were calculated by tensile test. Results: The strengths of the heat and self cured resin were respectively decreased and increased, when the filler was supplemented to the denture base resin and the modulus of elasticity of both heat and self cured resin were not increased, when the filler was supplemented to the denture base resin. Conclusion: The restoring forces of self cured resin containing 10% filler were increased, when the filler was supplemented to the denture base resin.

• 한국펄프종이공학회:학술대회논문집
• /
• 한국펄프종이공학회 2006년도 PAN PACIFIC CONFERENCE vol.1
• /
• pp.79-84
• /
• 2006

In order to improve filler-fiber bonding in paper, starch-filler composites were prepared by a starch-fatty acid complex formation method. These composites were used as a papermaking filler to improve the physical properties of the paper, filler retention and the sizing effect. The solubility of the starch-fatty acid complex in water at different temperatures was measured. The results indicated that the starch-fatty acid complexes have very low solubility in water below $70^{\circ}C$, which can be easily coated on clay surface to modify clay-fiber bonding ability. The clay-starch composite filled handsheets showed that paper strength could increase more than $100{\sim}200%$ compared to untreated clay. It was found that ZDT of the handsheet decreased as the clay content increased when unmodified clay was used, but it increased when the starch-fatty acid composite modified filler was used. It was also found that the presence of fatty acide in the complex increased the water-repellant property of the handsheet, which can be used to aid in sizing during papermaking. Filler distribution and bonding characteristics between the composite and fiber were investigated using Scanning Electron Microscopy(SEM).

• Journal of the Korean Wood Science and Technology
• /
• 제26권3호
• /
• pp.48-52
• /
• 1998

Residues such as walnut, pinenut and peanut shells were used as a filler in adhesive for bonding radiata pine plywood. The nutshell residues were prepared by simply drying to 8% moisture content and grinding the dry material using a laboratory Wiley mill with a $75{\mu}m$ (200 mesh) screen. The nutshells residues were compared to a commercial filler commonly used in adhesives by the structural plywood and laminated veneer lumber industry in the United States. The adhesive mixes were made by following the recommended procedure of Georgia-Pacific Resins, Inc., using phenol-formaldehyde resin. For each filler type, three-ply plywoods, 6 mm nominal thickness and 30 by 30 cm in size, were fabricated at two press times (4 and 5 min) and around 30 minute assembly time. Evaluations of the nutshell residues were carried out by tension shear tests after cyclic boil tests on plywood. The results of the performance test included tension shear strength and wood failure. All plywoods made with the nutshell fillers were comparable to those made with the control filler. These results indicate that nutshell residues would be suitable as filler for plywood adhesives.