• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2013.05a
• /
• pp.461-462
• /
• 2013

• The Journal of the Acoustical Society of Korea
• /
• v.9 no.2
• /
• pp.14-24
• /
• 1990

A Study is made on shrink fit shaft in which its part is modelled and spring stiffness per unit length is estimated, then obtained transfer matrix. Transfer matrix of shaft is found by Myklestad's method and natural frequency is found by shrink fit tolerance on shrink fit shaft, too. In order to verify effectiveness of shrink fit effect, hollow shaft of the same size is compared with shrink fit shaft which will verified on experiment. As a result of this study, the more shrink fit tolerance increases, the more spring stiffness per unit length increases. It is obvious from the above results that shrink fit shaft due to shrink fit tolerances decreases natural frequency.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.40 no.1
• /
• pp.171-187
• /
• 2016

The study performed a comparison analysis of market brand patterns for slim-fit dress shirts and analyzed the body surface development figure of men in their 40s using 3D body scan data and developed slim-fit dress shirt patterns suitable for middle-aged men. The sizes of slim-fit dress shirt patterns showed a slight difference depending on brand. The overlap map of slim-fit dress shirt patterns for brands demonstrates how difference of one-dimensional sizes reflect on two-dimensional patterns. This map provides useful information for pattern design and allows and easy recognition of pattern size differences. A try-on system evaluation through 3D-Simulation allows a grasp of the fitness of neckline and size tolerance of under the arms in front, the silhouette of side lines, and overall fitness in front that also allows analysis of the front/back balance of a shirt in side, the size tolerance proportion in front/back, and the fitness of the arm-hole line. Thus, we obtained try-on results that were equivalent to wearing actual clothing. According to the drafting size suggested in the developed final pattern, the total width was 'C/2+5.5cm', and the front was set at 1cm bigger in the size difference of the front and back. The width of the front neck and the back neck was set identically at 'C/12', while the width of the front neck was set to 'C/12+1.5cm'. For the armhole depth, we added 'C/4+2cm', and '0.5cm and 1.5cm' for the width of the front and back to anthropometry. The results of the try-on evaluation through 3D-Simulation indicated that the fitness of the final slim-fit dress shirt pattern was superior to available slim-fit dress shirt patterns on the market and evaluated as superior to the types for middle-aged men.

• Proceedings of the KWS Conference
• /
• 2007.11a
• /
• pp.300-302
• /
• 2007

• Journal of the Korean Data Analysis Society
• /
• v.20 no.6
• /
• pp.2721-2731
• /
• 2018

This study purposes to derive the predictive model for the cold tolerance of Brassica napus, using the data collected in the Tree Breeding Lab of Gyeongsang National University during July and August of 2016. Three Brassica napus samples were treated at each of low temperatures from $4^{\circ}C$ to $-12^{\circ}C$ by decrement of $4^{\circ}C$, step by step, and electrolyte leakage levels were measured at each stage. Electrolyte leakages were observed tangibly from $-4^{\circ}C$. We tried to fit the six nonlinear regression models to the electrolyte leakage data of Brassica napus: 3-parameter logistic model, baseline logistic model, 4-parameter logistic model, (4-1)-parameter logistic model, 3-parameter Gompertz model, and (3-1)-parameter Gompertz model. The baseline levels of the electrolyte leakage estimated by these models were 4.81%, 4.07%, 4.19%, 4.07%, 4.55%, and 0%, respectively. The estimated median lethal temperature, LT50, were $-5.87^{\circ}C$, $-6.31^{\circ}C$, $-6.05^{\circ}C$, $-6.35^{\circ}C$, $-4.98^{\circ}C$, and $-5.15^{\circ}C$, respectively. We compared and discussed the measures of goodness of fit to select the appropriate nonlinear regression model.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.34 no.10
• /
• pp.1632-1646
• /
• 2010

This article is an analysis of the fit preference of the knitted jacket according to body types for 30's and 40's adult women through a comparison of real and virtual fit. A five point likert scale was used to evaluate the degree of the preference of real and virtual fit. The data were analyzed with t-test and ANOVA using statistical program SPSS 17.0. The results are as follow. 1. The real and virtual fit preference of the knitted jacket according to body types indicates that respondents preferred pattern 2 for body type N than the rest of the patterns; however, respondents preferred pattern 3 for body type A and H. 2. There were no significant differences between real and virtual fit preference. 3. It is necessary that the knitted jacket follow a similar size tolerance like a woven jacket. The results show that the next generation of virtual try-on systems need the development of a minus clothing ease scale.

• Industrial Engineering and Management Systems
• /
• v.6 no.2
• /
• pp.94-105
• /
• 2007

Measurement technology plays an important role in discrete manufacturing industry. Probe-type coordinate measuring machines (CMMs) are normally used to capture the geometry of part features. The measured points are then fit to verify a specified geometry by using the least squares method (LSQ). However, it occasionally overestimates the tolerance zone, which leads to the rejection of some good parts. To overcome this drawback, minimum zone approaches defined by the ANSI Y14.5M-1994 standard have been extensively pursued for zone fitting in coordinate form literature for such basic features as plane, circle, cylinder and sphere. Meanwhile, complex features such as torus have been left to be dealt-with by the use of profile tolerance definition. This may be impractical when accuracy of the whole profile is desired. Hence, the true deviation model of torus is developed and then formulated as a minimax problem. Next, a relatively new and simple population based evolutionary approach, particle swarm optimization (PSO), is applied by imitating the social behavior of animals to find the minimum tolerance zone torusity. Simulated data with specified torusity zones are used to validate the deviation model. The torusity results are in close agreement with the actual torusity zones and also confirm the effectiveness of the proposed PSO when compared to those of the LSQ.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2011.06a
• /
• pp.571-572
• /
• 2011

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.13 no.5
• /
• pp.1-7
• /
• 2014

In this paper the structural analysis of a planet carrier was carried out for the design optimization of a slewing reducer used in tower cranes. The stress changes of the planet carrier according to the tolerance of interference fit were investigated, and the strength was evaluated on the basis of the stress level. The analysis results showed that the tolerance of interference fit have an important influence on the stress level of the planet carrier. To guarantee the static safety of carrier, the tolerances of carrier pinhole and planet pin as well as loading level exerted on the planet carrier should be determined considered correctly.

• The Korean Journal of Pesticide Science
• /
• v.9 no.3
• /
• pp.231-236
• /
• 2005

This study was conducted to determine the amounts of pesticide residues after treatment of criterion dose with 4 pesticides(tolclofos-m, folpet, procymidone, and triflumizole) under cultivated period and to compare the biological half-life of pesticides with 6 kinetic models(first, zero and second order kinetics, power function, elovich and parabolic model) and to establish proposed field tolerance using biological half-lives. Recovery of 4 pesticides form strawberry was ranged from 85.1 to 105.5%. For all of 4 pesticides, dissipation rate was over 73% at 5 days after application. Among 6 kinetic models, first order kinetic model (FO) was best fit to describe the relationship between residual pattern of pesticides and time. Therefore, half-lives were calculated by FO for establishing the field tolerance. These results showed that half-life should be calculated by comparative best fit kinetic model and field tolerance can help to prevent unacceptable agricultural products from marketing. It is good for both consumers and farmers having safe agricultural products and financial benefits, respectively.