• 한국정밀공학회지
• /
• 제31권2호
• /
• pp.165-170
• /
• 2014

Reproducibility of injection molding machines are studied at the study of this time. We applied computer aided engineering program so it could generate clamping force, about 1,500 kN, to the nozzle center part of flex link in tie-bar and at this time, we made sure condition of stress distribution and transformation quantity in flex link. The result of computer aided engineering transformation quantity was confirmed that transformation of top area was 247~257 kN and bottom areas was 273~279 kN and also was confirmed that the stresses are distributed in a range of 57~750 $N/mm^2$ from top to the bottom of the surface. This time we could confirm the condition of transformation quantity and stress distribution by enforcing the previously used structure analysis of flex link. And we utilized the reference data to establish important point of section for non destructive test overhaul.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2009년도 추계학술대회 논문집
• /
• pp.569-570
• /
• 2009

• 한국정보통신학회:학술대회논문집
• /
• 한국해양정보통신학회 2009년도 추계학술대회
• /
• pp.98-101
• /
• 2009

최근에는 차량 진단을 위한 방법으로 차량 내 네트워크 방식이 사용되고 있으며, CAN(Controller Area Network), MOST, LIN, FlexRay와 같은 차량 프로토콜의 사용 증대로 인해 차량에 대한 분산 제어와 원하는 데이터를 실시간 모니터링 하기 위한 방법들이 모색되고 있다. 현재의 자동차의 경우 자가진단 점검단자인 OBD2(On Board Diagnostics)표준 DLC(Data Link Connector)커넥터를 이용한 진단용 모듈(스캐너)을 통해 차량을 진단 한다. 그러나 엔진과 동력전달 계통(Powertrain) 부분으로 진단이 국한되어 있고, 사용자 측면을 고려하지 못하였다. 따라서, 본 논문에서는 Ethernet port를 이용한 차량 진단 모니터링 시스템을 설계하여 CAN 프로토콜 차량 데이터를 송수신하고 PC를 이용하여 보다 간편하게 차량의 상태와 정보를 제공하고 진단할 수 있는 모니터링 시스템을 구현한다.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2008년도 International Meeting on Information Display
• /
• pp.1491-1494
• /
• 2008

Typically internal mobile LCD display modules are connected to the mobile product baseband PCB with flexible printed circuit board equipped with board-to-board connector. This solution has a drawback of limiting the product concept work to certain solutions that are based on connector size, location, flexible PCB length, bending, etc. in the display module. Also flexible printed circuit board based solutions are not completely optimized from reliability point of view, causing flex circuit board breakings. For the external displays in the PC or Home entertainment market, the cable solution is too expensive and resource demanding. The wireless solution has obvious advantages over reliability, low cost and flexibility. This paper describes a wireless audio-visual interface solution.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• 제8권3호
• /
• pp.778-798
• /
• 2014

This paper proposes a novel exposed-terminal-eliminated medium access control (ETE-MAC) protocol by combining channel reservation, collision avoidance and concurrent transmissions to improve multi-access performance of the multihop wireless networks. Based on the proposed slot scheduling scheme, each node senses the control channel (CCH) or the data channel (DCH) to accurately determine whether it can send or receive the corresponding packets without collisions. Slot reservation on the CCH can be simultaneously executed with data packet transmissions on the DCH. Therefore, it resolves the hidden-terminal type and the exposed-terminal type problems efficiently, and obtains more spatial reuse of channel resources. Concurrent packet transmissions without extra network overheads are maximized. An analytical model combining Markov model and M/G/1 queuing theory is proposed to analyze its performance. The performance comparison between analysis and simulation shows that the analytical model is highly accurate. Finally, simulation results show that, the proposed protocol obviously outperforms the link-directionality-based dual-channel MAC protocol (DCP) and WiFlex in terms of the network throughput and the average packet delay.