• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2006.05a
• /
• pp.203-206
• /
• 2006

In this study, the method of designing the flexible wing model which will be used for wind tunnel testing of gust response alleviation system was presented. The design concept proposed herein was validated by performing the modal testing of the flexible wing model manufactured for demonstration purpose. In addition, the study on the gust response alleviation using flexible wing control surface was performed. For this purpose, optimal control with output feedback was adopted for designing the control surface controller, and the effects of gust response alleviation was validated by performing the numerical simulation for the representative flexible wing model. The methods proposed and validated in this study can be applied for wind tunnel testing of the flexible wing for gust response alleviation.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2007.11a
• /
• pp.1329-1332
• /
• 2007

In this study, the design method of flexible wing model for gust response measurement wind tunnel test was presented. The design concept proposed herein was validated by modal testing of the flexible wing model manufactured. In addition, aeroservoelastic modeling method for flexible wing model was presented and validated by comparing the gust response analysis results from the method proposed herein with those of commercial software. The gust response characteristics of the flexible wing model was studied by wind tunnel test for measuring the flexible wing gust response due to the induced gust excitation by gust generator. The aeroservoelastic modeling methods proposed and the wind tunnel test results obtained in this study can be applied for wind tunnel testing of the flexible wing for gust response alleviation.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2013.04a
• /
• pp.522-527
• /
• 2013

In this study, dynamic response control of a flexible wing such as gust loads alleviation using sliding mode control method is presented. To achieve this purpose, trailing edge control surface of a flexible wing is used as control means generating the aerodynamic control force. Aeroservoelastic CASE) model consisting of aeroelastic plant, control surface actuator model, and gust model depicting the atmospheric turbulence is formulated in the state space. A sliding mode controller based on the estimated state vector is designed for active dynamic response control of flexible wing aeroservoelastic model. The performance of the controller designed is demonstrated via numerical simulation for the representative flexible wing model under atmospheric turbulence loading.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2013.10a
• /
• pp.220-225
• /
• 2013

In this study, active control system using sliding mode control method is presented to achieve the gust response alleviation of a three-dimensional flexible wing model. For this purpose, aeroservoelastic model which is composed of aeroelastic plant, control surface actuator model, and gust model depicting the atmospheric turbulence is formulated in the state space. The aerodynamic force generated by the motion of a trailing edge control surface of a flexible wing is made use of as control means. An active control system combining state feedback sliding mode controller and state estimator based on measured responses such as wing tip acceleration and wing root strain is designed for gust response alleviation of a flexible wing aeroservoelastic model. The performance of the controller designed is demonstrated via numerical simulation for the representative flexible wing model under gust loading conditions.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.11 no.1
• /
• pp.225-232
• /
• 2019

In recent years, nonlinear dynamic models have been developed for flapping-type energy harvesting systems with a rigid wing, but not for those with a flexible wing. Thus, in this study, flexible wing designs of NACA0012 section are proposed and measurements of the forces of rigid cambered wings, which are used to estimate the performance of the designed wings, are conducted. Polar curves from the measured lift and drag coefficients show that JavaFoil estimation is much closer to the measured values than Eppler over the entire given range of angles of attack. As the camber of the rigid cambered wings is increased, both the lift and drag coefficients increase, in turn increasing the resultant forces. Moreover, the maximum resultant forces for all rigid cambered wings are achieved at the same angle of attack as the maximum lift coefficient, meaning that the lift coefficient is dominant in representations of the wing characteristics.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2014.10a
• /
• pp.189-192
• /
• 2014

Recently, development of electric powered UAV for high altitude and long endurance mission has been conducted worldwide. Long endurance requirement necessitates high lift over drag (L/D) aerodynamic characteristics and lightweight structures, leading to highly flexible wings with high aspect ratio. These highly flexible wings increase the danger of catastrophic aircraft failure due to flutter, which is a dynamic aeroelastic instability occurring from the interaction of aerodynamic, inertial, and elastic forces acting on the aircraft flying through the air. In this paper, flexible wing for electric powered UAV whose skin is fabricated using mylar film for lightweight design is briefly explained. In addition, flutter analysis procedures and results for the flexible wing in order to substantiate the aeroelastic stability requirements are presented.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.41 no.6
• /
• pp.448-457
• /
• 2013

This paper presents the design of an active flutter suppression system for flexible wing using sliding mode control method. The aerodynamic force generated by the motion of a flexible wing control surface is utilized as control force. For this purpose, aeroservoelastic model is formulated by blending aeroelastic model, control surface actuator model, and gust model. A sliding mode controller is designed for active flutter suppression on the aeroservoelastic model in conjunction with Kalman filter that estimates the system states based on the measured output. The performance of the designed controller is demonstrated via numerical simulation for the representative flexible wing model.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.49 no.3
• /
• pp.185-195
• /
• 2021

The flapping-wing micro air vehicle (FW-MAV) in this study utilizes the cambered wings made of quite flexible material. Similar to the flying creatures, the present cambered wing uses three different materials at its leading edge, vein, and membrane. And it is constrained in various conditions. Since passive rotation uses the flexible nature of the wing, it is important to select an appropriate material for a wing. A three-dimensional fluid-structure interaction solver is developed for a realistic modeling of the cambered wing. Then a parametric study is conducted to evaluate the aerodynamic performance in terms of the elastic modulus of leading edge and vein. Consequently, the elastic modulus plays a key role in enhancing the aerodynamic performance of FW-MAVs.

• Journal of computational fluids engineering
• /
• v.11 no.1 s.32
• /
• pp.21-28
• /
• 2006

Reliability Based Design Optimization(RBDO) is one of the optimization methods that minimize the product failure due to small changes of operating conditions or process errors. It searches the optimum that satisfies the safety margin of each constraint, and it gives stable and reliable designs. However, RBDO requires many times oj computational efforts compared with the conventional deterministic optimization(DO) to evaluate the probability of failure about each constraint, therefore it is hard to apply directly to large-scaled problems such as a flexible wing shape design optimization. For the efficient reliability analysis, the approximate reliability analysis method with the two-point approximation(TPA) is proposed In this study, the lift-to-drag ratio maximization designs are performed with 3-dimensional Navier-Stokes analysis and NASTRAN structural analysis, and the optimization results about the deterministic, FORM and SORM are compared.

• International Journal of Aeronautical and Space Sciences
• /
• v.17 no.1
• /
• pp.132-138
• /
• 2016

Korea Aerospace Research Institute (KARI) is developing an electric-driven HALE UAV in order to secure system and operational technologies since 2010. Based on the flight tests and design experiences of the previously developed electric-driven UAVs, KARI has designed EAV-3, a solar-powered HALE UAV. EAV-3 weighs 53kg, the structure weight is 22kg, and features a flexible wing of 19.5m in span with the aspect ratio of 17.4. Designing the main wing and empennage of the EAV-3 the amount of the bending due to the flexible wing, 404mm at 1-G flight condition based on T-800 composite material, and side wind effects due to low cruise speed, $V_{cr}=6m/sec$, are carefully considered. Also, unlike the general aircraft there is no center of gravity shift during the flight because of the EAV-3 is the solar-electric driven UAV. Thus, static margin cuts down to 28.4% and center of gravity moves back to 31% of the Mean Aerodynamic Chord (MAC) comparing with the previously designed the EAV-2 and EAV-2H/2H+ to upgrade the flight performance of the EAV-3.