• Journal of the Korea Institute of Building Construction
• /
• v.6 no.3 s.21
• /
• pp.75-82
• /
• 2006

This study investigates the influence of various blending factors on cement paste fluidity and find out the most effective evaluation method of cement paste flow, comparing flow test apparatuses such as ring flow(R-F), flow cone(F-C) and mini slump(M-S). A viscometer also measures the rheology coefficients to secure faithful numerical data. Firstly, series I examines cement paste, affected by several cement products and mineral admixture types in the range of W/B 40%, ordinary fluidity, and W/B 30%, high fluidity. In this series, the three types of cement product depended on companies, are randomly used and the mineral admixture, such as fly ash, blast furnace slag and silica fume, are incorporated in the cement paste, in response to the ratio of 10, 20, to 30%, respectively. In addition, series II studies various chemical admixture types, affecting the cement paste. This series is carried out with manufacturing companies and component types in the range of W/C 30%, high fluidity. For the manufacturing companies, randomly four products are used and for the component types, polycaboxylate, melamine, naphthalene and lignosulfonate type are chosen. Test results showed that in the fluidity test of cement paste considering various types of blending factors, R-F exhibited similar tendency with F-C and M-S. In the analysis of consistency curves measured by viscometer, the fluidity evaluation method using flow test apparatuses was significantly effective, except for the some of the low fluidity specimens. In conclusion of this study, R-F was the most convenient, faithful and effective fluidity evaluation method of cement paste.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.12
• /
• pp.8363-8369
• /
• 2015

This study is to be investigate properties of workability, compacting and compressive strength replaced by the illite powder in high fluidity concrete. For this purpose, illite powder has replaced the binder of high fluidity concrete of 5%, 10%, 15%, 20%. After concrete mixing, slump flow test, reach time slump flow 500mm, O-lot test were conducted on fresh high fluidity concrete. And compressive strength was determined 28 days for the hardened high fluidity concrete specimens. According to the test results, the workability, filling height of high fluidity concrete were increased in 10% replacement of illite powder. Furthermore, the compressive strength of high fluidity concrete was increased in 10% replacement of illite powder.. It was possible to confirm that optimal mixture ratio of illite powder seems to exist, and it is shown to be 10% according to our experimental results.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2016.05a
• /
• pp.137-138
• /
• 2016

Palm Oil Fuel Ash(POFA),which is burned in palm oil factories to get energy and gathered, has been studied in many countries due to its chemical properties. However POFA has high value of LOI and lots of pores on its particle surface. Therefore, in this study, POFA's fluidity were confirmed by mini-slump test and plastic viscosity test. Through the results, fluidity of POFA reduced according to the replacement ratio of POFA because of high value of LOI and its pores on surface and plastic viscosity of POFA increased. In addition, when superplasticizer was added, fluidity increased due to the steric effect of polycarboxylate superplasticizer.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2001.11a
• /
• pp.293-296
• /
• 2001

This paper presents the results of field application test on the manufacturing of high fluidity concrete by applying flowing methods with segregation reducing type superplasticizer. Base concrete is made with 20% of fly ash, which is flowed during the transportation. According to test results, fluidity, placeability and segregation reducing performance meet the range of high fluidity concrete after flowing, while air loss occurs due to fly ash. There are no noticeable differences in compressive strengths between non-compacting and compacting methods. According to non-destructive tests with rebound and core strength test, we cannot detect any differences in strength according to the height in the structures.

• Journal of the Korea Institute of Building Construction
• /
• v.15 no.2
• /
• pp.153-160
• /
• 2015

The marble powder is a by-product that can be freely collected during the manufacturing process of marble, such as sawing, shaping, and polishing. Disposal of this waste powder is one of the environmental problems worldwide today. Therefore, this study investigated to solve this problem by consuming the waste marble powder in high fluidity concrete, as a pore filler. For this purpose, the waste marble powder was used as a binder replacing 5%, 10%, 15%, and 20% of cement in high fluidity concrete. After mixing, slump flow test, time-to-reach the slump flow of 500mm test, O-lot test and U-box test were conducted with fresh concrete. For the hardened concrete, compressive strength was determined at the age of 28 days. According to the test results, the workability of high fluidity concrete increased with the powder of 15% replacement, and the compressive strength of high fluidity concrete also increased with the same amount of powder.

• Journal of the Korean Society for Geothermal and Hydrothermal Energy
• /
• v.8 no.2
• /
• pp.1-8
• /
• 2012

The G-class cement is usually used for geothermal well grouting to protect a steel casing which is equipped in a geothermal well to transfer geothermal water from deep subsurface to ground surface. In geothermal grouting process, obtaining appropriate fluidity is extremely important in order to fill cement grout flawlessly. In this paper, a series of the V-funnel and Slump Flow test was performed on both of the Portland cement and the G-class cement in order to compare fluidity and filling ability of those kind of cements. In the result of V-funnel test, the fluidity of G-class cement was evaluated much better than the Portland cement at the water/cement ratio of 0.8. In the case of Slump Flow test, the fluidity of G- class cement was estimated slightly better than the Portland cement at both the water/cement ratio of 0.55 and 0.8. Even though the initial fluidity and filling ability of G-class cement were relatively higher than the Portland cement, the results could be considerably changed with time. The results show that the fluidity and filling ability for geothermal well cementation can be properly controlled with water content and additives for adverse geothermal well environment.

• Journal of Korea Foundry Society
• /
• v.32 no.3
• /
• pp.127-132
• /
• 2012

Al-Zn-Mg alloys, being high strength aluminum alloys, have attracted attention as a material of automobile parts that require higher mechanical properties and lightness. Automobile parts with complex shapes are manufactured by low-priced casting method, but Al-Zn-Mg alloys are difficult to cast because of its poor hot cracking, feeding, and fluidity. Thus fluidity experiments on Al-Zn-Mg alloys were conducted for the castability evaluation. The effects of Mg and Zn, representative elements of Al-Zn-Mg alloys, on fluidity were observed. Spiral mold was used for fluidity experiments and the lengths of solidified specimens were measured after melting and gravity casting. Correlation between microstructures and fluidity length based on the alloy composition was considered. According to the experimental results, as the amount of Mg and Zn increased, fluidity decreased. Also, it was confirmed that fluidity change by the variation of Mg composition was greater than that of Zn.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1997.04a
• /
• pp.220-226
• /
• 1997

High flowing concrete has flowability, passability, segregation resistance and so on, and there are so many influence factor to affect to fluidity of high flowing concrete, therefore it is so difficult to evaluate exactly the properties in fresh state. This study is to analyze and evaluate thefluidity of high flowing concrete affected by fine aggregate with test method such as, slump-flow test, V-lot test, L-flow test, Box filling test.

• Journal of Korea Foundry Society
• /
• v.25 no.6
• /
• pp.240-248
• /
• 2005

The rheocasting characteristics are strongly influenced by the microstructural morphology such as particle size, form factor and contiguity. In this study, the effect of structural morphology on fluid flow characteristics of A356 semi-solid alloy was investigated with a vacuum suction fluidity test. Semi-solid metal slurry was made by the mechanical stirring, the liquidus casting, and H-NCM to be analysed. H-NCM could obtain uniform and fine globular microstructures of 0.9 form factor and 55 ${\mu}m$ particle size. Inoculation was found to be effective for reducing particle size, however, for H-NCM it should be avoided due to the cause of increasing contiguity. The fluidity test indicated that the non-stirring method had higher fluidity and smaller liquid segregation in the same solid faction of 0.4 than the stirring method, for smaller particle size and higher form factor. It was observed that liquid segregation decreased as the particle size is smaller and form factor is higher. The results of die-casting experiment were a good agreement with those of fluidity test.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2007.05a
• /
• pp.179-182
• /
• 2007

In recent, recycling of plastic material has became a major issue due to the landfills and environmental problem. This study investigated fluidity of thermoplastic vulcanizate(TPV), which is for automobile component parts such as weather strip in order to replace ethylene propylene rubber (EPDM). So, using the spiral flow test mold and panel cover mold, we conducted an experiment on fluidity of TPV with injection molding. As results of injection molding experiment, the recycled TPV's flow length was a little bit longer than virgin TPV and a case of panel cover, the filled weight was almost same quantity.