• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2007.05a
• /
• pp.279-280
• /
• 2007

In this study, it is investigated that the effect of material properties such as various temperature, forming speed and strain rates on formability and forming limits of Mg alloy sheet in square cup deep drawing. Since the sheet metal forming of Mg alloy is perform at elevated temperature, the effect of strain rates related with the forming temperature and forming speed is very important factor for formability and forming limits. Therefore, the investigation for process variables is necessary to improve formability and forming limits. Also, the effects of strain rate and thickness transformation were studied by the experimental and FE analysis using the square cup deep drawing. The temperature, forming speed, and strain rates were investigated. Forming of Mg alloy takes consider into temperature, proper forming speed and strain-rate the formed parts were good without defects fur forming limits.

• Transactions of Materials Processing
• /
• v.33 no.2
• /
• pp.87-95
• /
• 2024

The current study aims to prove that high-speed forming has better formability than conventional low-speed forming. Experimentally, the quasi-static forming limit diagram was obtained by Nakajima test, and the dynamic forming limit diagram was measured by electrohydraulic forming. For the experiments, the LS-DYNA was used to create the optimal specimen for electrohydraulic forming. The strain measurement was performed using the ARGUS, and comparison of the forming limit diagrams confirmed that EHF showed better formability than quasi-static forming. Theoretically, the Marciniak-Kuczynski model was used to calculate the theoretical forming limit. Swift hardening function and Cowper Symonds model were applied to predict the forming limits in quasi-static and dynamic status numerically.

• Transactions of Materials Processing
• /
• v.25 no.4
• /
• pp.261-267
• /
• 2016

High-speed forming process is the forming technology that deforms the blank in a very short time, with the strain rate of the blank above 1000 s⁻¹. Among many high-speed forming processes, electromagnetic forming (EMF) employs the Lorentz force when deforms the blank. Because of the high strain rate, the formability of the blank can be improved. However, when the blank is formed into rather complex shapes, it is bounced from the die and the wrinkles are generated. Therefore, electrohydraulic forming (EHF) is suggested in this study to reduce the bouncing problem of the blank. EHF is a high-speed forming that uses high voltage discharge in liquid. The shockwave resulting from the electric discharge propagates to the blank and it deforms the blank into the die. In this study, two high-speed forming processes, EMF and EHF were compared numerically with trapezoidal middle block die. This comparison showed that EMF cannot deform the blank into the die because of the bouncing, while EHF can overcome the bouncing problem and deform the blank into the die shape successfully.

• Journal of the Korean Society of Safety
• /
• v.15 no.3
• /
• pp.7-13
• /
• 2000

Forming characteristics of tailored blank are mostly effected by the welding method. Recently, laser welding is widely used for the tailored blank. However, tensile and forming characteristics vary due to welding conditions such as welding speed, heat flux etc. The objective of this paper is to evaluate the effect of welding speed on the tensile and forming characteristics of laser welded tailored blank. For this purpose, tailored blank specimens with different welding speed were prepared and tensile tests were performed. Also forming tests such as LDH and OSU test, were performed to evaluate the effect of welding speed on the forming characteristics. Finally, forming limit diagrams were obtained for different welding speed.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2008.05a
• /
• pp.378-382
• /
• 2008

Since the sheet metal forming of Mg alloy is perform at elevated temperature, the effect of strain rates related with the forming temperature and forming speed and R-value is very important factor for formability and forming limits and deep drawing. It is investigated that the effect of material properties such as various temperature, forming speed and strain rates on formability and R-value of Mg alloy sheet in round cup deep drawing. Therefore, the investigation for process variables is necessary to improve formability and forming limits and deep drawing. Also, the effects of strain rate and drawbility were studied by the experiment. The temperature, forming speed, and strain rates and R-value are investigated. Forming of Mg alloy takes consider into temperature, proper forming speed and strain-rate and R-value the formed parts were good without defects for forming limits and deep drawing.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2007.10a
• /
• pp.246-249
• /
• 2007

This study is concerned with deep drawability of magnesium sheets(AZ31B) at the warm conditions. Especially the dependency on forming speed has been investigated at the temperature of $200^{\circ}C$ and $300^{\circ}C$. Deep drawing test has been carried out at the temperature of $200^{\circ}C$ and $300^{\circ}C$. The die and blank holder are kept at test temperature by local heating and the punch is kept at room temperature by cooling technique. The magnesium sheets called AZ31B with the thickness of 0.5mm have been applied to deep drawing of circular cup. The drawability has been estimated at the conditions of forming speed (0.1, 1, 10 mm/sec). The results of deep drawing experiments show that the drawability is better at $300^{\circ}C$. Also the deep drawability is improved at the low speed(1mm/sec).

• Transactions of the Korean Society of Automotive Engineers
• /
• v.18 no.1
• /
• pp.127-130
• /
• 2010

This paper deals with the formability of DP590 steel considering the strain rate. The strain hardening coefficient, elongation and r-value were obtained from the static and dynamic tensile test. As strain rate increases from static to 100/s, the strain hardening coefficient and the uniform elongation decrease and the elongation at fracture and r-value decrease to 0.1/s and increase again to 100/s. The high speed forming limit tests with hemi-spherical punch were carried out using the high speed crash testing machine and high speed forming jig. The high speed forming limit of DP590(order of $10^2$/s) decreases compared to the static forming limit(order of $10^{-3}$/s) and the forming limit band in high speed forming test is narrower than that in the static forming test. This tendency may be due to the development of brittleness with increase of stain rate.

• Journal of the Korean Society for Precision Engineering
• /
• v.33 no.6
• /
• pp.477-483
• /
• 2016

The spring-back and bow phenomenon in the roll forming process are important factors regarding the accuracy of evaluation of production goods. The purpose of this study was to determine the influence of spring-back and bow phenomenon according to the main variables (forming velocity and roll gap). The material of the forming sheet was high tension steel (SPFH 590), which has been used commonly in recent years. In order to accurately measure the spring-back and bow phenomenon, the forming sheet was formed into a V-shape. The study was applied to OFAT (One Factor at a Time) experimentation, with respect to the experimental variables (the forming speed and the roll gap). In the experimental results, the forming speed had a small influence on the spring-back and bow phenomenon. However, the roll gap had a greater influence on the springback and the bow phenomenon, as opposed to the forming speed.

• Transactions of Materials Processing
• /
• v.11 no.4
• /
• pp.349-354
• /
• 2002

In order to find the effect of lubricant viscosity, sheet surface roughness, tool geometry, and forming speed on the frictional characteristics in sheet metal forming, a sheet metal friction tester was designed and manufactured and friction test of various sheet were performed. Friction test results showed that as the lubricant viscosity becomes lower, the friction coefficient is higher. When surface roughness is extremely low or high, the friction coefficient is relatively high. The result also show that as the punch radius and punch speed becomes bigger, the friction coefficient is smaller. Using experimental results, the mathematical expression between friction coefficient and lubricant viscosity, surface roughness, punch comer radius, or punch speed is also described.

• Transactions of Materials Processing
• /
• v.23 no.6
• /
• pp.363-368
• /
• 2014

Electromagnetic forming(EMF) is one of the high-speed forming methods, and has been used to deform metal sheets. The advantages of electromagnetic forming are reduced wrinkling due to non-contact characteristic and fine formability because of the high speed impact. In the current study, we suggest the application of electromagnetic forming to emboss pattern shapes using electromagnetic forces with only one forming coil and one punch. The high impact of the sheet at speeds of 100~300m/s produces significant coining pressure. In the current paper, electromagnetic forming was applied to Al 1100-O sheets; with thickness of 1.27mm and an area of $40mm{\times}40mm$. Using a single spiral coil, totally different types of patterns were created. Four different patterns were successfully produced on the aluminum sheet. The length and depth of the patterns were measured by three-dimensional scanning. Comparisons to the die shape showed good agreement. The test results confirm that emboss pattern forming by EMF using a single die can be used to replace the costly conventional method.