• Geomechanics and Engineering
• /
• 제5권3호
• /
• pp.195-221
• /
• 2013

A centrifuge model study is carried out to investigate the behavior of pile subject to negative skin friction induced by pile installation, ground water drawdown and surcharge loading. A single end-bearing pile is examined as the induced negative skin friction would induce the most severe stress on the pile structural material as compared to friction piles. In addition, the behavior of the pile under simultaneous negative skin friction and dead/live loads is examined. To facilitate detailed interpretations of the test results, the model setup is extensively instrumented and involves elaborate test control schemes. To further examine the phenomenon of negative skin friction on an end-bearing pile, finite element analyses were conducted. The numerical analysis is first validated against the centrifuge test data and subsequently extended to examine the effects of pile slenderness ratio, surcharge intensity and pile-soil stiffness ratio on the degree of mobilization of negative skin friction induced on the pile. Finally experimental and numerical studies are conducted to examine the effect of applied transient live load on pile subject to negative skin friction.

• 한국철도학회논문집
• /
• 제9권4호
• /
• pp.493-498
• /
• 2006

In this study, two large pile load tests were performed in the deep sand gravel deposit of Nakdong river basin so that the characteristics of the load transfer was identified. The fully instrumented rectangular barrette pile in the size of $1.5\times3.0m$ and the circular bored pile of the diameter 1.5 m were placed into the ground below 50 m. Under the applied loads of 2,400 tonf and 4,000 tonf, the test results of the load transfer showed the portion of 83% and 93% of the applied loads on the barrette pile and the bored pile, respectively, were supported by the skin friction along the pile shaft. It was revealed that the most of these skin friction mobilized in sand layer underlying clay layer having N-value more than 30 and that the friction per unit area of the bored pile was larger than the friction of barrette pile. However, if embedded in the stiff sand graval layer, the both piles were proven to be sufficient for using as the friction piles.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2009년도 세계 도시지반공학 심포지엄
• /
• pp.923-932
• /
• 2009

Generally most of pile foundations are constructed with group pile rather than single pile. The study on efficiency and bearing capacity which are major elements for rational design of this group pile has been actively progressed, whereas there are truly only a few studies of negative skin friction working on group pile due to the consolidation of ground. The purpose of this study is to determine, among the elements of negative skin friction applied to pile, the occurrence modality of negative skin friction at center, side, and corner of $3{\times}3$ group pile using model test and, based on those observations, to propose the effective design direction of group pile.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2005년도 춘계 학술발표회 논문집
• /
• pp.1-8
• /
• 2005

In this study, static pile load tests for instrumented drilled shaft pile and instrumented driven steel pipe pile were performed. Based on the results of pile load test, skin friction of each stratum was compared. Skin friction of drilled shaft were more than those of driven pile at the same settlement. This was based on the difference of surface roughness of piles and pile construction methods.

• Geomechanics and Engineering
• /
• 제8권6호
• /
• pp.769-781
• /
• 2015

The skin friction of a pile foundation is important and essential for its design and analysis. More attention has been given to the softening behaviour of skin friction of a pile. In this study, to investigate the load-transfer mechanism in such a case, an analytical solution using a nonlinear softening model was derived. Subsequently, a load test on the pile was performed to verify the newly developed analytical solution. The comparison between the analytical solution and test results showed a good agreement in terms of the axial force of the pile and the stress-strain relationship of the pile-soil interface. The softening behaviour of the skin friction can be simulated well when the pile is subjected to large loads; however, such behaviour is generally ignored by most existing analytical solutions. Finally, the effects of the initial shear modulus and the ratio of the residual skin friction to peak skin friction on the load-settlement curve of a pile were investigated by a parametric analysis.

• Geomechanics and Engineering
• /
• 제16권6호
• /
• pp.589-597
• /
• 2018

Centrifuge model tests were used to simulate pile-raft composite foundation and pile-geogrid composite foundation with different pile spacing for researching the time effect of negative skin friction of rigid piles in high-speed railways. The research results show that the negative skin friction has a significant impact on the bearing capacity of composite foundation. Pile-raft composite foundation has higher bearing capacity compared to pile-geogrid composite foundation to reduce the effect of negative skin friction on piles. Both the foundation settlement and negative skin friction have significant time effect. The distribution of skin friction can be simplified as a triangle along the pile. The neutral point position moves deeper in the postconstruction stage at larger pile spacing. For pile-geogrid composite foundation, the setting of pile-cap affects the position of neutral point in the post-construction stage. Reinforced cushion with geotextile may promote the better performance of cushion for transmitting the loads to piles and surrounding soils. Arching effect in the cushion of the composite foundation is a progressive process. The compression of the rigid piles contributes less than 20% to 25% of the total settlement while the penetration of the piles and the compression of the bearing stratum below the pile tips contribute more than 70% of the total settlement. Some effective measures to reduce the settlement of soils need to be taken into consideration to improve the bearing capacity of pile foundation.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 1999년도 말뚝기초위원회 워크샵
• /
• pp.141-154
• /
• 1999

Under the compressible circumstance of a soil deposit, the soil move downward relative to the pile. The down drag force requires higher point bearing and causes failure of a pile from time to time. In this paper the mechanism of negative skin friction on a pile, design and reduction of the negative friction is reviewed.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2010년도 춘계 학술발표회
• /
• pp.1077-1087
• /
• 2010

Generally most of pile foundations are constructed with group pile rather than single pile. The study on efficiency and bearing capacity which are major elements for rational design of this group pile has been actively progressed, whereas there are truly only a few studies of negative skin friction working on group pile due to the consolidation of ground. The purpose of this study is to determine, among the elements of negative skin friction applied to pile, the occurrence modality of negative skin friction at center, side, and corner of $3{\times}3$ group pile using model test and, based on those observations, to propose the effective design direction of group pile.

• 한국지반공학회지:지반
• /
• 제8권2호
• /
• pp.21-30
• /
• 1992

말뚝의 주면마찰력은 전체 지지력중 상당한 하중을 지지할 수 있으나 실제 설계시에는 무시되는 경우가 많이 있다. 주면마찰력을 설계에 반영할 경우에도 계산결과의 신뢰도는 매우 낮은 것이 현실이다. 국내의 사정은, 설계 자료로 활용할 수 있는 것은 표준관입시험 결과뿐인 경우가 대부분으로 빈곤하며 특히 국내에 많은 화강암, 편마암의 풍화잔류토에 관해서는 설계자료가 극히 희박해 외국에 비해 열악하다. 최근에 국내에서 개발된 간편한 말뚝재하시험(simple pile loading test: SPLT)의 사용은 선단지지력과 주면마찰력의 별도 측정이 가능하도록 하였다. 본 연구에서는 풍화잔류토 지반에서의 SPLT 결과를 분석하여 N값에 의한 새로운 설계관계식을 제안하였다.

• 한국지반공학회지:지반
• /
• 제14권5호
• /
• pp.163-172
• /
• 1998

말뚝의 지지력 거동을 연구하기 위하여 말뚝 제작시 다수의 변형률계를 설치한 2본의 말뚝들에 대하여 항타시에 그리고 항타후 소정의 시간이 경과된 시점에 동재하시험과 정재하시험을 몇 차례 수행하였다. 콘관입저항값 그리고 표준관입저항값과 말뚝의 단위 주면마찰력과의 관계를 규명하기 위해 재하시험전에 시험지반에 대하여 론관입시험과 표준관입시험도 실시하였다. 지지력과 두부침하량 관계를 살펴보면, 0.055D(D: 직경)의 두부침하량에서 전체지지력이 극한에 도달하였고, 이 때에 주면마찰력은 극한간에 도달했으나, 선단지지력은 계속 증가하는 것으로 나타났다. 말뚝의 지지력은 항타후 시간이 경과함에 따라 자연대수함수로 증가하였으며, 지지력 성분중 주면마찰력 성분이 항타한 후 40일 경과한 시점에 초기값의 4.6배 정도로 현저하게 증가하였다. 지지력 거동에 대한 시간경과의 영향을 보면, 시험말뚝들은 초기항타시에는 선단지지말뚝으로 거동하다가 시간이 경과하면서 주면마찰 말뚝으로 거동이 변화되었음을 관찰할 수 있었다. 단위 주면마찰력은, 토질분류에 따라 다르지만, 콘관입저항칼(q.)과 표준관입저항값(N)과 일정한 관계를 갖는 것으로 나타났으며, 관계상수는 현재 국내에서 사용하고 있는 간보다 큰 것으로 나타났다.