• 한국산학기술학회논문지
• /
• 제16권9호
• /
• pp.6019-6026
• /
• 2015

본 연구에서는 소량생산 및 개인 맞춤형 제작으로 매우 유용한 3D 프린팅 기술을 이용하여 자가 맞춤형 부목을 제작하고자 하였다. 방법으로는 3D 프린터를 이용하여 용융적층조형방식(fused deposition modeling)으로 부목을 제작하였으며, 재료는 열가소성 플라스틱 계열인 ABS(acrylonitrile butadiene styrene) 수지를 이용하였다. 부목의 모델링은 실제 인체의 손 부위 3차원 전산화단층영상을 이용하였으며 통풍이 가능하도록 설계하였다. 그 결과 실제 인체 손 모양과 일치하는 자기 맞춤형 부목이 성공적으로 출력되었다. 또한 기존 부목보다도 우수한 방사선영상을 획득할 수 있었다. 결론적으로 본 연구에서 제시한 3D 프린팅 사례는 ABS 수지를 이용한 용융적층조형방식의 유사한 구조물을 출력할 때 기초자료로 사용할 것으로 판단된다.

• 대한방사선기술학회지:방사선기술과학
• /
• 제39권3호
• /
• pp.337-344
• /
• 2016

본 연구에서는 3차원(3-dimensional, 3D) 프린팅 기술로 출력된 팬톰에 대한 X선 투과성을 평가하고자 하였다. 3D 프린팅 방식은 용융적층조형(fused deposition modeling, FDM) 방식을 이용했으며 소재는 아크릴로나이트릴 뷰타다이엔 스타이렌(acrylonitrile butadiene styrene, ABS)을 사용하였다. 팬톰은 원통 모양으로 설계하였으며 전산화단층영상장비(computed tomography, CT)에서 획득한 단면영상으로 균일도를 측정하였다. X선 투과성 평가는 3D 출력된 팬톰 내부에 이온챔버를 삽입하여 실시하였다. 그 결과, 평균 균일도가 2.70 HU이었으며 기존 폴리메틸 메타크릴레이트(poly methyl methacrylate, PMMA) CT 팬톰과 3D 프린터로 출력된 팬톰에서 측정된 X선 투과성의 상관관계는 0.976로 높은 상관관계가 있는 것으로 나타났다. 향후 3D 프린팅 기술을 이용한 방사선정도관리 팬톰 제작에 기초자료로 활용할 수 있으리라 기대한다.

• Elastomers and Composites
• /
• 제51권4호
• /
• pp.301-307
• /
• 2016

Additive manufacturing (AM), so called 3D Printing is a new manufacturing process and is getting attraction from many industries. There are several methods of 3D printing. Among them fused deposition modeling (FDM) type is most widely used by reason of cheap maintenance, easy operation and variety of polymeric materials. Articles manufactured by 3D printing have weak deposition strength compared with conventionally manufactured products. Deposition strength of FDM type 3D printed article is highly dependent of deposition temperature. Subsequently the nozzle temperature in the FDM type 3D printing is very important and it is controlled by heat source in the 3D printer. Nozzle is connected with heat block and barrel, and heat block contains heat source. Nozzle becomes hot through heat conduction from heat source. Nozzle temperature has been predicted for various thermal boundary conditions by computer simulation and compared with experimental measurement. Nozzle temperature highly depends upon thermal conductivities of heat block and nozzle. Simulation results are good agreement with experiment.

• International Journal of Internet, Broadcasting and Communication
• /
• 제16권1호
• /
• pp.176-181
• /
• 2024

The desktop-level 3D printing machines makes it easier for independent designers to produce collectible models. Desktop 3D printers that use FDM (Fused Deposition Modeling) technology usually use a minimum nozzle diameter of 0.4mm. When using FDM printers to make Gunpla models, Thin slice structures are prone to slicing errors, which lead to deformation of printed objects and reduction in structural strength. This paper aims to analyze the printing model that produces errors, control a single variable among the three variables of slice layer height, slice wall thickness and filament type for comparative testing, and find a way to avoid gaps. To provide assistance for using FDM printers to build models containing thin-walled structures.

• Elastomers and Composites
• /
• 제52권3호
• /
• pp.216-223
• /
• 2017

The additive manufacturing technology, also called 3D printing, is growing fast. There are several methods for 3D printing. Fused deposition modeling (FDM) type 3D printing is the most popular method because it is simple and inexpensive. Moreover, it can be used for printing various thermoplastic materials. However, it contains the cooling of layered road and causes thermal shrinkage. Thermal shrinkage should be controlled to obtain high-quality products. In this study, temperature distribution and cooling behavior of a layered road with cooling are studied through computer simulation. The thermal shrinkage of the layered road was simulated using the calculated temperature distribution with time. Shape variation of the layered road was predicted as cooling proceeded. Stress between the bed and the layered road was also predicted.This stress was considered as the detaching stress of the layered road from the bed. The simulations were performed for various thermal conductivities and temperatures of the layered road, bed temperature, and chamber temperature of a 3D printer. The simulation results provide detailed information about the layered road for FDM type 3D printing under operational conditions.

• Journal of Yeungnam Medical Science
• /
• 제40권3호
• /
• pp.302-307
• /
• 2023

With recent developments in digital dentistry, research on techniques and materials for three-dimensional (3D) printing is actively underway. We report the clinical applications and outcomes of 3D printing of temporary crowns fabricated with polylactic acid (PLA) using a fused deposition modeling (FDM) printer. Five participants were recruited from among patients scheduled to be treated with a single full-coverage crown at a dental clinic in a university medical center from June to August 2022. We used 3D-printed crowns fabricated with PLA using an FDM printer as temporary crowns and were assessed for discomfort, fracture, and dislodging. The 3D-printed temporary crowns were maintained without fracture, dislodging, or discomfort until the permanent prosthesis was ready. The average time required for printing the temporary crowns was approximately 7 minutes. The 3D printing of temporary crowns with PLA using an FDM printer is a convenient process for dentists. However, these crowns have some limitations, such as rough surface texture and translucency; therefore, the 3D printing process should be improved to produce better prostheses.

• Elastomers and Composites
• /
• 제58권1호
• /
• pp.44-56
• /
• 2023

Additive manufacturing (AM) or three-dimensional (3D) printing of metals has been drawing significant attention due to its reliability, usefulness, and low cost with rapid prototyping. Among the various AM technologies, fused deposition modeling (FDM) or fused filament fabrication is receiving much interest because of its simple manufacturing processing, low material waste, and cost-effective equipment. FDM technology uses metal-filled polymer filaments for 3D printing, followed by debinding and sintering to fabricate complex metal parts. An efficient binder is essential for producing polymer filaments and the thermal post-processing of printed objects. This study involved an in-depth investigation of and a fabrication route for a novel multi-component binder system with steel alloy powder (45 vol.%) ranging from filament fabrication and 3D printing to debinding and sintering. The binder system consisted of polyvinyl pyrrolidone (PVP) as a binder and thermoplastic polyurethane (TPU) and polylactic acid (PLA) as a carrier. The PVP binder held the metal components tightly by maintaining their stoichiometry, and the TPU and PLA in the ratio of 9:1 provided flexibility, stiffness, and strength to the filament for 3D printing. The efficacy of the binder system was examined by fabricating 3D-printed cubic structures. The results revealed that the thermal debinding and sintering processes effectively removed the binder/carrier from the cubic structures, resulting in isotropic shrinkage of approximately 15.8% in all directions. The scanning electron microscopy (SEM) and energy dispersive X-ray spectroscopy (EDX) patterns displayed the microstructure behavior, phase transition, and elemental composition of the 3D cubic structure.

• 한국결정성장학회지
• /
• 제32권1호
• /
• pp.33-39
• /
• 2022

3D 프린터 관련 특허가 만료되고 주요 기술이 공개되면서 3D 프린터 가격이 하락하면서 원하는 제품을 쉽게 찾을 수 있는 환경이 조성되고 있다. 특히 가장 저렴한 FDM(Fused Deposition Modeling) 3D 프린터가 다양한 분야에서 사용되고 있다. FDM 방식은 형상을 출력할 때 특정 조건이상에서는 지지대(Support)를 붙여야만 형상의 무너짐 없이 제작이 가능하다. 지지대를 달지 않고 형상을 출력할 때 특정 각도에서 발생하는 불규칙한 표면은 제품에 있어서는 불량이지만 예술과 공예적 측면에서는 또 다른 재미를 느낄 수 있는 요소로 활용될 수 있다고 사료된다. 본 논문에서는 이러한 불규칙한 표면을 얻기 위해 출력에 영향을 줄 수 있는 요인들을 제어하고 출력 각도만 변위요소로 실험하였다. 실험 결과 수직에서 62°~70°의 각도로 프린팅 시 필라멘트가 흘러내리지 않고 불규칙한 표면을 얻을 수 있었다. 또한 인위적으로 불규칙한 표면을 공예적인 제품에 적용해 보았다.

• 한국기계가공학회지
• /
• 제14권4호
• /
• pp.62-72
• /
• 2015

Interest in three-dimensional (3D) printing processes has grown significantly, and several types have been developed. These 3D printing processes are classified as Selective Laser Sintering (SLS), Stereo-Lithography Apparatus (SLA), and Fused Deposition Modeling (FDM). SLS can be applied to many materials, but because it uses a laser-based material removal process, it is expensive. SLA enables fast and precise manufacturing, but available materials are limited. FDM printing's benefits are its reasonable price and easy accessibility. However, metal printing using FDM can involve technical problems, such as suitable component supply or the thermal expansion of the heating part. Thus, FDM printing primarily uses materials with low melting points, such as acrylonitrile butadiene styrene (ABS) or polylactic acid (PLA) resin. In this study, an FDM process for enabling metal printing is suggested. Particularly, the nozzle and heatsink for this process are focused for stable printing. To design the nozzle and heatsink, multi-physical phenomena, including thermal expansion and heat transfer, had to be considered. Therefore, COMSOL Multiphysics, an FEM analysis program, was used to analyze the maximum temperature, thermal expansion, and principal stress. Finally, its performance was confirmed through an experiment.

• 한국콘텐츠학회논문지
• /
• 제15권1호
• /
• pp.308-315
• /
• 2015

본 연구는 3D 프린터를 이용하여 통풍이 원활하고 위생적이며 선명한 방사선영상을 구할 수 있는 그물형 손목 부목을 제작하고자 하였다. 스캐너는 의료용 다중단층영상장치(MDCT)를 이용했으며, 3D 프린터 기기는 용융 적층 조형술(fused deposition modeling, FDM)의 프린팅 방식을 이용했다. 소재는 분해성 플라스틱 (poly lactic acid, PLA)을 사용하였다. 손목의 3 차원 볼륨렌더링은 MDCT에서 획득된 단층영상으로 구현하였다. 구현된 손목 3 차원 영상을 바탕으로 가상의 그물형 부목 모형을 디자인하고 출력하였다. 그 결과 3D 프린터로 출력된 부목이 기존 부목보다도 우수한 방사선 손목영상을 획득할 수 있었으며 가려움증 및 비위생적인 단점을 개선하고 부목 해체 작업이 용이하였다. 결론적으로 본 연구에서 모델링된 3D 부목 모형은 향후 3D 프린팅 부목 제작에 기초자료로 활용할 수 있으며 환자들의 실생활에 도움을 줄 것으로 기대한다.