• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.21 no.4
• /
• pp.321-328
• /
• 2008

In this paper, variable gain amplifier(VGA) with a gain slope controller has been proposed and verified by circuit simulations and measurements. The proposed VGA has a gain control, gain slope switch and variable gain range. The input source coupled pair with diode connected load is used for VGA gain stage. The gain slope controller with switch can control VGA gain slope. The proposed VGA is fabricated in $0.18{\mu}m$ CMOS process for multi -standard wireless receiver. The proposed two stage VGA consumes min. 2.0 mW to max. 2.6 mW in gain control range and gives input IP3 of -3.77 dBm and NF of 28.7 dB at 1.8 V power supply under -25 dBm, 1 MHz input. The proposed VGA has 37 dB(-16 dB $\sim$ 21 dB) variable gain range, and 8 dB gain range control per 0.3 V control voltage, and can provide variable gain, positive and negative gain slope control, and gain range control. This VGA characteristics provide design flexibility in multi-standard wireless receiver.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.4 no.1
• /
• pp.83-92
• /
• 2001

In this paper, the monopulse channel receiver which can be matched between channels through a wide bandwidth has been proposed. The effects of the gain and phase imbalance between channels on the slope of monopulse error signal were analyzed. Also, the matching method between channels in a wide bandwidth was proposed, by which monopulse slope could be stabilized. Using the implemented monopulse radar system the monopulse slope was measured in the anechoic chamber which include the moving horn antenna and the target signal generator. The results show that the wide band matching method is useful and applicable to various channel receivers

• Journal of IKEEE
• /
• v.11 no.1 s.20
• /
• pp.38-45
• /
• 2007

A new 8-bit single-slope ADC using analog RAMP generator with digitally controllable dynamic range has been proposed and simulated for column level or per-pixel CMOS image sensor application. The conversion gain of ADC can he controlled easily by using frequency divider with digitally controllable diviber ratio, coarse/fine RAMP with class-AB op-amp, resistor strings, decoder, comparator, and etc. The chip area and power consumption can be decreased by simplified analog circuits and passive components. Proposed frequency divider has been implemented and verified with 0.65um, 2-poly, 2-metal standard CMOS process. And the functional verification has been simulated and accomplished in a 0.35$\mu$m standard CMOS process.

• Current Optics and Photonics
• /
• v.2 no.4
• /
• pp.356-360
• /
• 2018

We demonstrate continuous-wave operation of an all-fiber thulium-holmium codoped laser operating at a wavelength of 1706.3 nm. To realize laser operation in the short-wavelength region of the emission-band edge of thulium in silica fiber, we employ fiber Bragg gratings having resonant reflection at a wavelength around 1700 nm as a wavelength-selective mirror in an all-fiber cavity scheme. We first examine the performance of the laser by adjusting the central wavelength of the in-band pump source. Although a pump source possessing a longer wavelength is observed to provide reduced laser threshold power and increased slope efficiency, because of the characteristics of spectral response in the gain fiber, we find that the optimal pump wavelength is 1565 nm to obtain maximum laser output power for a given system. We further explore the properties of the laser by varying the fiber gain length from 1 m to 1.4 m, for the purpose of power scaling. It is revealed that the laser shows optimal performance in terms of output power and slope efficiency at a gain length of 1.3 m, where we obtain a maximum output power of 249 mW for an applied pump power of 2.1 W. A maximum slope efficiency is also estimated to be 23% under these conditions.

• Transactions on Electrical and Electronic Materials
• /
• v.18 no.5
• /
• pp.250-252
• /
• 2017

High-performance full swing logic inverters were fabricated using amorphous 1 wt% Si doped indium-zinc-oxide (a-SIZO) thin films with different channel layer thicknesses. In the inverter configuration, the threshold voltage was adjusted by varying the thickness of the channel layer. The depletion mode (D-mode) device used a TFT with a channel layer thickness of 60 nm as it exhibited the most negative threshold voltage (-1.67 V). Inverters using enhancement mode (E-mode) devices were fabricated using TFTs with channel layer thicknesses of 20 or 40 nm with excellent subthreshold slope (S.S). Both the inverters exhibited high voltage gain values of 30.74 and 28.56, respectively at $V_{DD}=15V$. It was confirmed that the voltage gain can be improved by increasing the S.S value.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.11
• /
• pp.635-639
• /
• 2016

In the devices used in the microwave frequency band, the gain decreases as the frequency increases due to the parasitic component. To compensate for these characteristics, a linear gain equalizer with an opposite slope is needed in wideband systems, such as those used for electronic warfare. In this study, a linear gain equalizer that can be used in the 18 ~ 40GHz band is designed and fabricated. Circuit design and momentum design (optimizations) were carried out to reduce the errors between design and manufacturing. A thin film process is used to minimize the parasitic components within the implementation frequency band. A sheet resistance of 100 ohm/square was employed to minimize the wavelength variation due to the length of the thin film resistor. This linear gain equalizer is a structure that combines a quarter wavelength-resonator on a series microstrip line with a resistor. All three 1/4 wavelength short resonators were used. The fabricated linear gain equalizer has a loss of more than -5dB at 40GHz and a 6dB slope in the 18 ~ 40GHz band. By using the manufactured gain equalizer in a multi-stage connected device such as an electronic warfare receiver, the gain flatness degradation with increasing frequency can be reduced.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2003.06a
• /
• pp.129-144
• /
• 2003

Generally, investigation methods of cut slope are conducted only geological surface survey to gain engineering geological data of cut slopes. These methods have many problems such as limitations of investigation for a special area. So geophysical investigations such as geotomography, seismic and electrical resistivity methods have been used to search for failure surface in potential failure slopes or failed slopes. But investigation method using the borehole camera is recently a used method and it is thought that this method is more reliable method than other investigation methods because of being able to see by the eyes. Therefore, this paper was conducted investigations of borings and BIPS(Borehole Image Processing System) to search for potential sliding surfaces and was applied to obtain information of discontinuity on failed and potential failure slope in highway. As the results of BIPS, we could decide potential sliding surface in the slope, conducted to check slope stability and decided slope stability measures.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.11 no.10
• /
• pp.1937-1943
• /
• 2007

Given the mountainous nature of Korea, cutting slopes are bound to happen. Every you, slope failures lead to enormous human and material losses. More recently, reckless development and subsequent degradation of forests has brought about soil erosion, which coupled with heavy rainfall, contaminates rivers, raises the level of river bottoms and thereby deteriorates their discharge capacity. In Korea, environmental impact assessments and disaster impact assessments have been conducted to come up with proper countermeasures. In order to perform quantitative analysis for this purpose, reliable slope information is quintessential. This study aims to obtain slope-related digital images using an RC model helicopter with a non-metric camera embedded, and to process these images to gain more accurate slope information. To this end, digital images obtained regarding cutting slopes were processed to gain numerical information of slopes and, on the basis of slope information gained here, reliable soil erosion factors were estimated.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.34D no.2
• /
• pp.10-20
• /
• 1997

This paper describes the design, the manufacture and the development of th eautomatic gain control unit which ajdusts the gain of IF processor in the high sensitive & multifunctional receiver unit (HMR) for pulse doppler radar system. Accodording to the effective distnce of target, radar cross section, and a lot of external environments (such as clutter), the receiving stage of RADAR system often deviates from dynamic range. To solve this kind o fproblem, continuous/pulse wave AGC are realized, make it possible to control the gain characteristics of receiver stably, and can increase dynamic range linearly by adjusting the gain slope of receiver which is limited by 1-dB gain compression point. In this study, AGC unit is designed to regulate the total gain of receiver by using te analog feedback theory. It also has rapid enough response to process pulse signal. This study presents the gain control method of IF, the real manufacture technique (the package-type components) and the measurement performance of AGC.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.18 no.11
• /
• pp.1299-1308
• /
• 2007

In this paper, we propose the calibration method of monopulse slope to minimize the variation of angle estimate in frequency agile noncoherent monopulse system. We analyze the monopulse slope characteristics of antenna and RF receiver including the phase and gain imbalances of each receiving channel and present the calibration method to minimize the phase and gain imbalances of RF receiver channels including antenna. In addition, we present the calibration method using channel switching to minimize the gain imbalance of IF receiver channels. The measured average monopulse slope within the frequency bandwidth is -0.96, the maximum variation of angle estimate is similar to theoretical value, $0.15^{\circ}$ at ${\pm}2^{\circ}$ azimuth and $0.03^{\circ}$ at $0^{\circ}$ azimuth.