• Proceedings of the KSME Conference
• /
• 2007.05a
• /
• pp.215-219
• /
• 2007

In this work, the indium zinc oxide (IZO) films had been deposited on the glass substrate coated with the SiO film. Based on a comparative investigation of the IZO monolayer and IZO/SiO multilayer, it is shown that the thickness of SiO film has a great effect on the mechanical properties of the thin films. The AFM images of the IZO thin film included the SiO film were shown smoother surfaces than monolayer. Resistivity was in inverse proportion to Mobility. If it deposited the SiO film on the substrate, the layer of change was generated between two layer(SiO and substrate). The layer of change influenced resistance because of oxygen content was more than the IZO monolayer.

• Analytical Science and Technology
• /
• v.6 no.2
• /
• pp.239-246
• /
• 1993

The structure of $(BaSr)TiO_3$ thin film deposited on ITO coated glass, bare glass and (100) Si substrates was not changed, but the crystallinity was improved by the polycrystalline ITO layer and (100) Si substrate. The composition of $(BaSr)TiO_3$ thin film deposited on ITO coated glass was nearly stoichiometric ((Ba+Sr)/Ti=1.08~1.09) and very uniform through all deposition process. But as the deposition temperature increases, the interdiffusion between grown thin film and ITO layer and between ITO layer and base glass is severer. $(BaSr)TiO_3$ thin film deposited on ITO coated glass substrate was highly transparent. The refractive index($n_f$) of $(BaSr)TiO_3$ thin film deposited on ITO coated glass was 2.138~2.286 as a function of substrate temperature.

• Journal of the Microelectronics and Packaging Society
• /
• v.19 no.4
• /
• pp.33-37
• /
• 2012

Microstructure developments of $RuO_2$ based thick film resistors during firing as a function of glass viscosity were analytically quantified and its effect on the electrical property was investigated. The microstructure development was retarded as the viscosity of glass was increased. It was found that the viscosity range for each stage of microstructure development are as follows ; $7500-10^5Pa{\cdot}s$ for the glass sintering, $2000-7500Pa{\cdot}s$ for the glass island formation, $700-2000Pa{\cdot}s$ for the glass spreading, and $50-700Pa{\cdot}s$ for the infiltration. The sheet resistivity decreased as the viscosity of glass in the resistor film increased due to the higher chance of sintering for the conductive particles with the higher viscosity of the glass.

• Journal of the Korean institute of surface engineering
• /
• v.46 no.3
• /
• pp.111-115
• /
• 2013

To study the encapsulation method for large-area organic light emitting devices (OLEDs), OLED of ITO / 2-TNATA / NPB / $Alq_3$:Rubrene / $Alq_3$ / LiF / Al structure was fabricated, which on $Alq_3$/LiF/Al as protective layer of OLED was deposited to protect the damage of OLED, and subsequently it was encapsulated using attaching film and flat glass. The current density and luminance of encapsulated OLED using attaching film and flat glass has similar characteristics compared with non-encapsulated OLED when thickness of Al as a protective layer was 1200 nm, otherwise power efficiency of encapsulated OLED was better than non-encapsulated OLED. Encapsulation process using attaching film and flat glass did not have any effects on the emission spectrum and the Commission International de L'Eclairage (CIE) coordinate. The lifetime of encapsulated OLED using attaching film and flat glass was 287 hours in 1200 nm Al thickness, which was increased according to thickness of Al protective layer, and was improved 54% compared with 186 hours in same Al thickness, lifetime of encapsulated OLED using epoxy and flat glass. As a result, it showed the improved efficiency and the long lifetime, because the encapsulation method using attaching film and flat glass could minimize the impact on OLED caused through UV hardening process in case of glass encapsulation using epoxy.

• Journal of the Korean Society for Precision Engineering
• /
• v.27 no.12
• /
• pp.28-32
• /
• 2010

Technical demands for aspheric glass lens formed in market increases its application from simple camera lens module to fiber optics connection module in optical engineering. WC is often used as a metal core of the aspheric glass lens, but the long life time is issued because it fabricated in high temperature and high pressure environment. High hard thin film coating of lens core increases the core life time critically. Diamond Like Carbon(DLC) thin film coating shows very high hardness and low surface roughness, i.e. low friction between a glass lens and a metal core, and thus draw interests from an optical manufacturing industry. In addition, DLC thin film coating can removed by etching process and deposit the film again, which makes the core renewable. In this study, DLC films were deposited on the SiC ceramic core. The process variable in FVA(Filtered Vacuum Arc) method was the substrate bias-voltage. Deposited thin film was evaluated by raman spectroscopy, AFM and nano indenter and measured its crystal structure, surface roughness, and hardness. After applying optimum thin film condition, the life time and crystal structure transition of DLC thin film was monitored.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.1
• /
• pp.105-112
• /
• 2018

This paper proposes a method for fabricating heatable glass using the conduction characteristics of metal thin films deposited on the surface of Low-e(Low emissivity) glass. The heating value of Low-e glass depends on the Joule heat caused by Low-e glass sheet resistance. Hence, its prediction and design are possible by measuring the sheet resistance of the material. In this study, silver electrodes were placed at 50 mm intervals on a soft Low-e glass sample with a low emissivity layer of 11 nm. This study measured the sheet resistance using a 4-point probe, predicted the power consumption and heating value of the Low-e glass, and confirmed the heating performance through fabrication and experience. There are two conventional methods for manufacturing heatable glass. One is a method of inserting nichrome heating wire into normal glass, and the other is a method of depositing a conductive transparent thin film on normal glass. The method of inserting nichrome heating wire is excellent in terms of the heating performance, but it damages the transparency of the glass. The method for depositing a conductive transparent thin film is good in terms of transparency, but its practicality is low because of its complicated process. This paper proposes a method for manufacturing heatable glass with the desired heating performance using Low-e glass, which is used mainly to improve the insulation performance of a building. That is by emitting a laser beam to the conductive metal film coated on the entire surface of the Low-e glass. The proposed method is superior in terms of transparency to the conventional method of inserting nichrome heating wire, and the manufacturing process is simpler than the method of depositing a conductive transparent thin film. In addition, the heat characteristics were compared according to the patterning of the surface thin film of the Low-e glass by an emitting laser and the laser output conditions suitable for Low-e glass.

• Polymer(Korea)
• /
• v.37 no.5
• /
• pp.656-662
• /
• 2013

The flexible patterned cover film was made by a simple solution coating process using polymethyl methacrylate (PMMA) solution with glass beads. The effect of patterned cover film on the efficiency of solar cell has been investigated. It was found that the relative solar cell efficiency increased up to 3.4% with the incident light angle between $0-90^{\circ}$ by the sphere shape of glass bead coated on the film surface. This was understood that the loss of transmittance and scattering due to the light directional dependency on solar cell were minimized because the light entered glass beads normal to its surface regardless of incident light angle. The maximum relative solar cell efficiency was achieved when glass bead shape on the film is hemisphere and the relative efficiency increased with increasing the amount of glass bead on the film surface. However, too much glass beads on the film surface resulted in the lower relative solar cell efficiency due to the lowering of transmittance as well as the occurring of light interference.

• Proceedings of the Korean Ceranic Society Conference
• /
• 1986.12a
• /
• pp.259-267
• /
• 1986

The sintering behavior of silver-oxide glass composite thick-film has been studied with varing glass content. It is shown that during heat treatment glass became liquid phase to deeply affect the microstructure development of the silver particles and to control the physical properties of the thick-films. As glass content increased, the initial repacking of silver particles took place rapidly but the homogeneities of the microstructure showed different features. When the glass content was over some range, the silver particles exuded glass to decrease net energy and glass formed liquid pools separated from the solid skeletons. Finally the relations between the microstructures and electrical properties of the thick-film were discussed.

• Journal of the Microelectronics and Packaging Society
• /
• v.14 no.3
• /
• pp.57-64
• /
• 2007

New Chip-on-glass technology to attach an Si chip directly on the glass substrate of LCD panel was studied with local heating method of the Si chip by using thin film heater fabricated on the Si chip. Square-shaped Cu thin film heater with the width of $150\;{\mu}m$, thickness of $0.8\;{\mu}m$, and total length of 12.15 mm was sputter-deposited on the $5\;mm{\times}5\;mm$ Si chip. With applying current of 0.9A for 60 sec to the Cu thin film heater, COG bonding of a Si chip to a glass substrate was successfully accomplished with reflowing the Sn-3.5Ag solder bumps on the Si chip.

• Journal of the Korean Ceramic Society
• /
• v.45 no.2
• /
• pp.87-89
• /
• 2008

A nano structured silica aerogel thin film was manufactured from inexpensive sodium silicate (water glass) using an ambient pressure drying method. High purity silicic sol was prepared by passing a water glass solution through an ion exchange resin, and the gel films were prepared on a modified glass substrate via dip coating. The dip coating conditions, such as coating time and solvent, were optimized. The optical and physical properties of the obtained silica aerogel thin film were characterized using a UV-visable spectrometer and a scanning electron microscope.