• Journal of electromagnetic engineering and science
• /
• v.12 no.1
• /
• pp.55-62
• /
• 2012

Humanitarian demining is very important issue not only in mine affected courtiers but also for the courtiers which are technically, politically and financially supporting the mine affected courtiers. In order to achieve higher efficiency of the mine clearance operation, new technologies can significantly contribute to the societies. Since 2002, Tohoku University, Japan has developed a sensor system "ALIS" for humanitarian demining. ALIS is a hand-held dual sensor, which combines an electromagnetic induction sensor (EMI) and a Ground Penetrating Radar (GPR). ALIS has a real-time sensor tracking system based on a CCD camera and which enables the image reconstruction. We have tested ALIS in Cambodia and found that it can eliminate more than 70 % metal fragments. Since 2009, 2 sets of ALIS have detected more than 80 anti-personnel mines, and cleared more than 137,000 $m^2$ in Cambodia.

• Journal of the Korean Society for Aviation and Aeronautics
• /
• v.12 no.3
• /
• pp.65-85
• /
• 2004

Circling to land is a relatively dangerous maneuver. It contains the worst elements of IFR flight. There is a minimum obstruction clearance, a limited space in which to maneuver, an absence of visual reference, and trying to keep the runway in sight while preparing to land. At night it is quite a bit more than dangerous. The required continuous turn in marginal conditions that keeps the airport in sight is hazardous. Therefore, this paper proposes an application of GNSS to circling approach to reduce or remove chances of accidents which may occur under such unfavorable flight conditions. The study reviews relevant documents published by ICAO and FAA and provides scenarios for non-precision and precision approaches and circling approach based on the GNSS for Kimhae airport. Also requirements for the ground facility design are studied and provided.

• Journal of the Korean Institute of Rural Architecture
• /
• v.11 no.1
• /
• pp.47-56
• /
• 2009

According to the user recognizing, the propose of this study is to establish the systematic church-design and the plan of rational process. When the plan of church design is rational come out, the local community will be risen and there is the possibility which will raise the essential function of church construction and design. The results from the study are as follow. Firstly, the area of the front-window and the number of the external entrance are correlated with the accessibility of the building. Secondly, the height of a bell-tower is related with the feelings of a tediously and a intimate degree. Thirdly, the ground clearance of the whole surface is correlated with the church-character and the community formation of a local society.

• Proceedings of the KIEE Conference
• /
• 2009.07a
• /
• pp.399_400
• /
• 2009

This paper presented operation rules on short-term Emergency rating of transmission lines in KEPCO. And we suggested a operation grouping and its maximum conductor temperature considering facility conditions - conductor lifetime, stability of connection points, conductor height above ground and clearance, in the operating and new T/L.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2001.10a
• /
• pp.190-195
• /
• 2001

The piercing and blanking of thin sheet metal working is specified division in press die design and making. In order to prevent the defects, the optimum design of the production part, strip process layout, die design, die making and try out etc. are necessary the analysis of effective factors. For example, theory and practice of metal shearing process and it's phenomena, die structure, machine tool working for die making, die materials and it's heat treatment, metal working in field, their know how etc. are included in those factors. In this study, we analyzed whole of data base, theoretical back ground of metal working process, and then performed the progressive die tryout with the screw press.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.25 no.7
• /
• pp.72-77
• /
• 2011

Dynamic Line Rating (DLR) techniques have been greatly worthy of notice for efficiently increasing transmission capacity as well as controlling load-flow in overhead transmission lines, in comparison with the existing power system operating with Static Line Rating (SLR). This paper describes an utilization method to implement DLR control system for old transmission lines built in the first stage using the ground clearance design standard with lower dips. The suggested DLR system is focused on designing as temperature control system rather than current/load control system. Based on several performance for conductor temperatures, it is shown that DLR system with efficiency can be implemented.

• Proceedings of the KIEE Conference
• /
• 2006.10c
• /
• pp.193-195
• /
• 2006

In this study, we developed an active controlled ankle-foot orthosis(AAFO) which can control the dorsiflexion/plantarflexion of the ankle joint during gait to prevent foot drop and toe drag for paralysis patients. To prevent dropping foot after heel strike, ankle joint was actively controlled to minimize forefoot collision with the ground. It was also controlled to provide toe clearance and to help push-off during late stance. The 3D gait analysis was performed on two healthy subjects equipped with the developed AAFO to compare with the normal gait and the conventional AFO gait. In the developed AAFO gait, differently from the conventional AFO gait, significant push-off was observed during pre-swing and the maximum flexion moment during pre-swing phase was similar to that of normal gait. A remarkable dorsiflexion also occurred during initial swing. These results indicated that the developed AAFO could have certain clinical benefits to prevent foot drop for paralysis patients, compared to conventional AFOs.

• Proceedings of the Korea Committee for Ocean Resources and Engineering Conference
• /
• 2000.04a
• /
• pp.146-150
• /
• 2000

In order to prevent the defects, the optimum design of the production part, strip process layout, die design, die making and try out etc. are necessary the analysis of effective factors. For example, theory and practice of metal shearing process and it's phenomena, die structure, machine tool working for die making, die materials and it's heat treatment, metal working in field, their know how etc. are included in those factors. In this study, we analyzed whole of data base, theoretical back ground of metal working process, and then performed the progressive die tryout with the screw press. Part2 of this study reveals with ultra precision progressive die design, its making and tryout.

• Proceedings of the Korea Committee for Ocean Resources and Engineering Conference
• /
• 2000.04a
• /
• pp.35-39
• /
• 2000

The piercing and blanking of thin sheet metal working is specified division in press die design and making. In order to prevent the detects, the optimum design of the production part, strip process layout, die design, die making and try out etc. are necessary the analysis of effective factors. For example, theory and practice of metal shearing process and its phenomena, die structure, machine tool working for die making, die materials and its heat treatment, metal working in industrial and its know how etc. In this study, we analyzed whole of data base, theoretical back ground of metal working process, and then performed the progressive die tryout with the screw press. This study regards to the aim of small quantity of production parts press working. Part 1 of this study reveals with production part and strip process layout design.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2000.04a
• /
• pp.229-233
• /
• 2000

In order to prevent the defects, the optimum design of the production part, strip process layout, die design, die making and try out etc. are necessary the analysis of effective factors. For example, theory and practice of metal shearing process and it's phenomena, die structure, machine tool working for die making, die materials and it's heat treatment, metal working in field, their know how etc. are included in those factors. In this study, we analyzed whole of data base, theoretical back ground of metal working process, and then performed the progressive die tryout with the screw press. Part2 of this study reveals with ultra precision progressive die design, its making and tryout.