• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.15 no.3
• /
• pp.265-270
• /
• 2004

This paper addresses the effect of group delay in satellite communication system. Phase of signal is distorted by the non-constant group delay. Group delay can be modeled as linear, parabolic and cubic type according to the polynomial characteristic. We investigate BER performance of satellite communication system with each 3 kinds of group delay. As signal bandwidth becomes wider, group delay makes more influence on the signal. BNR performance of satellite communication system is found when data rates are 1Mbps, 4Mbps and 8Mbps. Convolution coding with the code rate of 1/2 or 7/8 is used. At BER =10$\^$-5/, system with group delay needs more SNR of minimum 0.3㏈ to maximum 4.4㏈ than system without group delay. The worst case of BER performance happens in the linear group delay, 7/8 punctured convolution coding and 8 Mbps. The required SNR is increased by 4.4㏈ at this worst case.

• Journal of electromagnetic engineering and science
• /
• v.12 no.2
• /
• pp.166-170
• /
• 2012

This paper presents a tunable composite right/left-handed (CRLH) delay line for a delay line discriminator that linearizes modulated frequency sweep in a frequency modulated continuous wave (FMCW) radar transmitter. The tunable delay line consists of 8 cascaded unit cells with series varactor diodes and shunt inductors. The reverse bias voltage of the varactor diode controlled the group delay through its junction capacitance. The measured results demonstrate a group delay of 8.12 ns and an insertion loss of 4.5 dB at 250 MHz, while a control voltage can be used to adjust the group delay by approximately 15 ns. A group delay per unit cell of approximately 1 ns was obtained, which is very large when compared with previously published results. This group delay can be used effectively in FMCW radar transmitters.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.37A no.10
• /
• pp.895-902
• /
• 2012

In this paper, we propose a novel equalizer to compensate for the group delay including AM/PM nonlinear distortion characteristics by the nonlinear power amplifier (PA). The group delay characteristic is a nonlinear non-constant time delay that appears differently depending on each frequency component. The phase distortion by AM/PM characteristics arising from the power amplifier is a major factor to increase group delay. By the group delay distortion, the signal in the constellation expands and is rotated. Considering the problem mentioned above, the nonlinear time delay that appears differently depending on each frequency component is classified as a static group delay and AM/PM characteristic of PA, the different phase transitions depending on the size of input signal as a dynamic group delay. Static group delay estimates and compensate for phase distortions in the frequency domain with type-based method and dynamic group delay compensates for phase rotation in the time domain. We confirmed that the group delay compensation techniques were enough to compensate the group delay characteristics including AM/PM characteristics of the power amplifier.

• ETRI Journal
• /
• v.25 no.5
• /
• pp.379-386
• /
• 2003

This paper presents the design of a narrow-band channel filter and its group-delay equalizer for a Ka-band satellite transponder. We used an 8th order channel filter for high selectivity with an elliptic-integral function response and an inline configuration. We designed a 2-pole, reflection-type, group-delay equalizer to compensate for the steep variation of the group-delay at the output of the channel filter, keeping the thermal stability at ${\pm}7$ ns of group-delay variation at the band edges over 15-55$^{\circ}C$. We devised a new tuning technique using short-ended dummy cavities and used it for tuning both the filter and equalizer; this removes the necessity of additional tuning after the cavities are assembled. Through measurement, we demonstrate that the group-delay-equalized filter meets the equipment requirements and is appropriate for satellite input multiplexers.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.9 no.6
• /
• pp.2180-2200
• /
• 2015

This paper considers mobility control to improve packet delivery in delay-tolerant networks (DTNs) under group mobility. Based on the group structure in group mobility, we propose two mobility control techniques; group formation enforcement and group purposeful movement. Both techniques can be used to increase the contact opportunities between groups by extending the group's reachability. In addition, they can be easily integrated into some existing DTN routing schemes under group mobility to effectively expedite the packet delivery. This paper is divided into 2 parts. First, we study how our proposed mobility control schemes reduce the packet delivery delay in DTNs by integrating them into one simple routing scheme called group-epidemic routing (G-ER). For each scheme, we analytically derive the cumulative density function of the packet delivery delay to show how it can effectively reduce the packet delivery delay. Then, based on our second proposed technique, the group purposeful movement, we design a new DTN routing scheme, called purposeful movement assisted routing (PMAR), to further reduce the packet delay. Extensive simulations in NS2 have been conducted to show the significant improvement of PMAR over G-ER under different practical network conditions.

• Journal of electromagnetic engineering and science
• /
• v.3 no.2
• /
• pp.140-146
• /
• 2003

In this paper, the design of a channel filter and its group-delay-and-amplitude equalizer is carried out for the Ka-band satellite transponder subsystem. The 8th order dual-mode filter is employed for high selectivity around the band-edges with an elliptic-integral function response and has an in-line configuration. The 2-pole, reflection-type, group-delay equalizer is designed and manufactured to reduce the group-delay and amplitude variation, which can be large for such a high order filter. It is noted that in both the filter and equalizer, adopting the dual-mode coupling mechanism leads to less mass and volume. Through measurement, the performance of the realized group-delay-equalized filter is shown to meet the equipment requirements and to be appropriate for the satellite input multiplexer.

• Proceedings of the IEEK Conference
• /
• 2000.11a
• /
• pp.113-116
• /
• 2000

The effect due to group delay and non linear characteristics in high speed data satellite channel was represented in this paper. Based on the modeling of group delay and non linear characteristics the performance was analyzed in ka band satellite channel. The group delay and non-linear characteristics in high speed data transmission severely affect the system performance. The more Eb/No is required to satisfy the required system performance. The optimum operating points of HDR satellite transmission system are implemented by considering analyzed results for channel characteristics

• Journal of electromagnetic engineering and science
• /
• v.19 no.1
• /
• pp.56-63
• /
• 2019

Typical negative group delay circuits (NGDC) are analyzed in terms of signal attenuation, group delay, and bandwidth using S-parameters. By inverting these formulations, we derive and present the design equations (for NGD circuit elements) for a desired specification of the two among the three parameters. The proposed design method is validated through simulation examples for narrow- and wide-band pulse inputs in the time and frequency domains. Moreover, an NGDC composed of lumped elements is fabricated at 1 GHz for measurement. As a function of frequency, the circuit-/EM-simulated and measured group delays are in good agreement. The provided simple NGDC design equations may be useful for many applications that require compensations of some signal delays.

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2003.11a
• /
• pp.496-500
• /
• 2003

In This paper, a pole-zero optimized design method for multi-layed planar interdigital stripeline linear group delay bandpass filter with tap input port is presented. As a design example, a four-pole group delay filter with center frequency of 2.14GHz, bandwidth of 160MHz, and group delay variation of ${\pm}0.1nS$ for LTCC technology or multilayerd PCB technology is designed. In the design process, as well the whole structure is not necessary to be simulated, and within three times of optimizing process we have good result as well. This design method could be useful for controlling error correction of manufacturing process as well as design stage.

• ETRI Journal
• /
• v.34 no.2
• /
• pp.210-215
• /
• 2012

In this paper, a group delay time controller (GDTC) is proposed based on a reflection topology employing a parallel resonator as the reflection termination. The design equations of the proposed GDTC have been derived and validated by simulation and experimental results. The group delay time can be varied by varying the capacitance and inductance at an operating frequency. To show the validity of the proposed circuit, an experiment was performed for a wideband code division multiple access downlink band operating at 2.11 GHz to 2.17 GHz. According to the experiment, a group delay time variation of $3{\pm}0.17$ ns over bandwidth of 60 MHz with excellent flatness is obtained.