• Transactions of the Society of Information Storage Systems
• /
• v.8 no.1
• /
• pp.33-38
• /
• 2012

To investigate of load/unload performance, FE (finite element) model of conventional suspension and HAMR suspension were made. The FE models were verified by modal analysis. In the loading simulation, the conventional system could stably load onto the disk without contact. On the other hand, the HAMR suspension which had an optical fiber and prism occurred slider - disk contact. In the unloading process, the conventional system was unloaded without contact. However, in the HAMR suspension, the contact between slider and disk was occurred at the moment that the dimple was separated during unload process. Therefore the load/unload performance of HAMR decrease with high stiffness, it is necessary that stiffness of HAMR suspension should reduced with design parameters of optical fiber and prism.

• Transactions of the Society of Information Storage Systems
• /
• v.8 no.2
• /
• pp.61-66
• /
• 2012

In HDD industry, many technologies have been developed and investigated as means to increase the areal density of drives. Especially, heat assisted magnetic recording (HAMR) system has been considered as the next generation storage device. Most of the HAMR systems use near field optics as heating mechanism. Therefore, light delivery system is indispensable. We considered the light delivery system with laser diode (LD) mount and optical fiber. Mass and stiffness of the HAMR system using these LD mount and optical fiber are changed. The mass and stiffness of the HAMR system affects the slider dynamic behavior. It is necessary to analyze touch down (TD) and take off (TO). And, we performed the TD-TO experiment with HAMR suspension. Finally, we analyzed the result of TD-TO experiments. And we suggested the design of HAMR suspension to improve TD-TO performance.

• Transactions of the Society of Information Storage Systems
• /
• v.7 no.1
• /
• pp.36-41
• /
• 2011

The micro laser module was designed and prepared to deliver the light to the HAMR head. It consists of laser diode, photo diode and actuator to realize stable light delivery even though the head is fluctuated during the disk rotation. The optical evaluation was carried out with the actual distance between the light source and HAMR head with a range of reflectivity and it was found that the incident angle could be controlled within ${\pm}0.125^{\circ}$ to maintain same intensity into the HAMR head. It was also confirmed that the designed micro laser module is thermally stable without any severe effect on the magnetic head.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2009.05a
• /
• pp.68-69
• /
• 2009

Heat Assisted Magnetic Recording (HAMR) is one of the most promising candidates for high density magnetic storages over 1 Tb/$in^2$ areal density. Since the precise light delivery to the head is a key factor to realize HAMR application, it is required to establish the light delivery using micro laser module and micro actuator. For the careful control of micro actuator, a laser module was designed including laser diode, optical fiber, collimating lens, and fabricated V-groove substrate. In addition, the basic aligning method between the laser module and HAMR head was studied by the detection of current change in photo diode due to the amount of reflected light from the head.

• Proceedings of the Korean Magnestics Society Conference
• /
• 2007.05a
• /
• pp.261.1-261.1
• /
• 2007

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2010.05a
• /
• pp.681-682
• /
• 2010

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2010.11a
• /
• pp.501-502
• /
• 2010

• Current Applied Physics
• /
• v.18 no.11
• /
• pp.1381-1387
• /
• 2018

One dimensional (1D) grating has been fabricated (using focused ion beam) on 50 nm gold (Au) film deposited on higher refractive index Gallium phosphate (GaP) substrate. The sub-wavelength periodic metal nano structuring enable to couple photon to couple with the surface plasmons (SPs) excited by them. These grating devices provide the efficient control on the SPs which propagate on the interface of noble metal and dielectric whose frequency is dependent on the bulk electron plasma frequency of the metal. For a fixed periodicity (${\Lambda}=700 nm$) and slit width (w = 100 nm) in the grating device, the efficiency of SPP excitation is about 40% compared to the transmission in the near-field. Efficient coupling of SPs with photon in dielectric provide field localisation on sub-wavelength scale which is needed in Heat Assisted Magnetic recording (HAMR) systems. The GaP is also used to emulate Vertical Cavity Surface emitting laser (VCSEL) in order to provide cheaper alternative of light source being used in HAMR technology. In order to understand the underlying physics, far-and near-field results has been compared with the modelling results which are obtained using COMSOL RF module. Apart from this, grating devices of smaller periodicity (${\Lambda}=280nm$) and slit width (w = 22 nm) has been fabricated on GaP substrate which is photoluminescence material to observe amplified spontaneous emission of the SPs at wavelength of 805 nm when the grating device was excited with 532 nm laser light. This observation is unique and can have direct application in light emitting diodes (LEDs).

• Journal of Magnetics
• /
• v.19 no.3
• /
• pp.237-240
• /
• 2014

For heat-assisted magnetic recording, magnetization reversal probabilities of nano-Pt/MnSb multilayer film with perpendicular magnetic anisotropy under thermal pulse activation were investigated numerically by solving the Landau-Lifshift Gilbert Equation. Magnetic parameters of nano-Pt/MnSb multilayer were used with anisotropy energy of $3{\times}10^5$ erg/cc and saturation magnetization of 2100 G, which offer more than 10 y data stability at room temperature. Scheme of driven magnetic field and thermal pulse on writing mechanism was designed closely to real experiment. This study found that the chosen material is potential to be used as a high density magnetic storage that requires low writing field less than two-hundreds Oersted through definite heating and cooling interval. The possibility of writing data with a zero driven magnetic field also became an important result. Further study is recommended on the thickness of media and thermal pulse design as the essential parameters of the reversal magnetization.

• Transactions of the Society of Information Storage Systems
• /
• v.1 no.1
• /
• pp.1-22
• /
• 2005

There are two important trends in the modern information society, including digital networking and ubiquitous environment. Thus it is strongly required to develop new information storage devices such as high density storages to match the increased data capacity and small size storage devices to be applied to the mobile multimedia electronics. So far, many approaches have been studied for the high density memory, including the holographic memory, super-RENS and near-field recording using solid immersion lens (SIL) or nano-probe for the ODD (Optical Disk Drive) system, and the perpendicular magnetic recording and heat-assisted magnetic recording for the HDD (Hard Disk Drive) system. In addition, new mobile storage devices have been prepared using 0.85" HDD and 30mm ODD systems from a lot of foreign and domestic companies and institutes. In this paper, the recent technology trend for the next generation information storage system is summarized to offer a research motivation and encouragement to new researchers in this field with an emphasis on the technical issues of the increase of data capacity and decrease of device size.