• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.54 no.4
• /
• pp.195-200
• /
• 2005

In this paper, we proposed the electric circuit using one common arm of H-Bridge Inverters to reduce the number of switching component in multi-level inverter combined with H-Bridge Inverters and Transformers. and furthermore we suggested the new multi-level PWM inverter using PWM level to reduce THD(Total Harmonic Distortion). and we used the switching method that can be same rate of usage at each transformer. Also, we tested the proposed prototype 9-level inverter to clarify the proposed electric circuit and reasonableness of control signal for the proposed multi-level PWM inverter.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.51 no.9
• /
• pp.537-544
• /
• 2002

This paper describes a comparative analysis of soft switching boost converters through design, production and experiment. Soft switching boost converters are designed to satisfy the condition of input voltage 170-265Vac, output voltage 400Vdc, output current 5A, output power 20W-2000W and unit power factor. In addition, parameter values are designed so that system operation can be compared under this is similar conditions. The efficiency of the combined inductor soft switching boost converter was 97.63% with 1011 load better than that of other boost converter types. The combined inductor soft switching converter has simple circuit construction and low switching loss. EMI resulted by the switching noise, and harmonic distortion.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.55 no.10
• /
• pp.505-510
• /
• 2006

This paper deals with skew and overhang effects of permanent magnet linear synchronous motor(PMLSM). The detent force and thrust characteristics considering skew and overhang effects of permanent magnet are analyzed by 3D finite element method and the results are compared to experimental values. As skew and overhang are applied to permanent magnet, the thrust is almost the same value but the detent force is reduced remarkably. By harmonic analysis, the distortion ratio of thrust is remarkably reduced from 4.29[%] to 2.3[%]. and, the ripple ratio of thrust is decreased from 8.2[%] to 3.56[%] at the same time. But, the lateral force which operate as the perpendicular direction of skew direction is generated. The lateral force and normal force acts by braking force between mover and LM-guide.

• Proceedings of the KIEE Conference
• /
• 2002.06a
• /
• pp.125-130
• /
• 2002

This paper examines the application of high voltage static var compensator(SVC) with cascade multilevel inverter which employs H~bridge inverter(HBI). The SVC system is modeled using the d-q transform which calculates the instantaneous reactive power. This model is used to design a controller and analyze the SVC system. From the mathematical model of the system, the design procedures of the circuit parameters Land C are presented in this thesis. To meet the specific total harmonic distortion(THD) and ripple factor of the capacitor voltage, the circuit parameters Land C are designed. Simulated and experimental results are also presented and discussed to validate the proposed schemes.

• Journal of Power Electronics
• /
• v.11 no.5
• /
• pp.677-687
• /
• 2011

In this paper a cycloconverter-type high frequency transformer link inverter with a reduced switch count is analyzed and designed. The proposed topology consists of an H-bridge inverter at the transformer's primary side and a cycloconverter with three bidirectional switches at the secondary. All of the switches of the cycloconverter operate in non-resonant zero voltage and zero current switching modes. To overcome a high voltage surge problem resulting from the transformer leakage inductance, phase angle control based on natural commutation is employed. The effectiveness of the proposed inverter is verified by constructing s 750W prototype. Experimentally, the inverter is able to supply a near sinusoidal output voltage with a total harmonic distortion of less than 1%. For comparison, a PSpice simulation of the inverter is also carried out. It was found that the experimental results are in very close agreement with the simulation.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.18 no.5
• /
• pp.422-428
• /
• 2013

Recently, we use a static synchronous compensator(STATCOM) with cascaded H-bride topologies, because it is easy to increase capacity and to reduce total harmonic distortion(THD). When we use equipment for reactive power compensation, dc-link voltage unbalances occur from several reasons although loads are balanced. In the past, switching pattern change of single phase inverter and reference voltage magnitude change of inverter equipped with power sensor have been used for dc-link voltage balance. But previous methods are more complicated and expensive because of additional component costs. Therefore, this paper explains reasons of dc-link voltage unbalance and proposes solution. This solution is complex method that is composed of reference voltage magnitude change of inverter without additional hardware and shifted phase angle of inverter reference voltages change. It proves possibility through 1000[KVA] system simulation.

• Proceedings of the KIEE Conference
• /
• 2003.07b
• /
• pp.1211-1213
• /
• 2003

A pulse width modulation(PWM) method for single-phase Sepic-type rectifier is introduced in this paper. The characteristics of the proposed PWM system are high performance high power factor with low input current harmonic distortion. The proposed control method is based on the average-current-mode using the dedicated integrated circuit UC3854 this technique it is possible to implement a very simple control circuit for unitary power-factor in CCM operation and also to provide over-current protection.

• Proceedings of the KIPE Conference
• /
• 2001.07a
• /
• pp.163-166
• /
• 2001

In this paper, a two-level switching algorithm ov the deadbeat to control PWM inverter is proposed. A modified algorithm of the deadbeat is suitable for the UPS system. Two levels in the pulse pattern are used. This scheme allows the use of higher switching frequency for a given computation time delay, which results in lower total harmonic distortion at the output. The proposed control scheme is implemented using TMS320F240 DSP for controlling on inverter.

• Proceedings of the KIPE Conference
• /
• 2002.11a
• /
• pp.137-139
• /
• 2002

This paper proposes a four times DC-link voltage PWM power converter, which is constructed by four cascade connected power switching devices. such as IGBT. These four switching devices are controlled by a sinusoidal PWM method to obtain a DC-link voltage. which is higher than 4 times the peak supply voltage, and to suppress input current harmonic components. achieving a sinusoidal current waveform with less than $3[\%]$ distortion. Which is also constructed by four cascade connected IGBT. by the simulation result.

• Journal of Power Electronics
• /
• v.6 no.2
• /
• pp.146-162
• /
• 2006

This paper deals with the analysis, design and implementation of an AC-DC Zeta converter in discontinuous current mode (DCM) of operation used for power quality improvement at AC mains in direct torque controlled (DTC) permanent magnet synchronous motor (PMSM) drives. The designed Zeta converter feeds a direct torque controlled PMSM drive system. Modeling and simulation is carried out in a standard PSIM software environment. Test results are obtained on the developed prototype Zeta converter using DSP ADMC401. The results obtained demonstrate the effectiveness of the Zeta converter in improving power quality at AC mains in the PMSM drive system.