• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2006년도 춘계학술대회논문집
• /
• pp.774-781
• /
• 2006

This paper presents a study on the analytical prediction of vibration transmission from helical gears to the bearing. The proposed method is based on the application of the three dimensional helical gear behaviors and complete description of shaft by the spectral method. Helical gear system used in this paper consists of the driving element, helical gears, shafts, bearings, couplings and load element. In order to describe all translation and rotation motion of helical gears twelve degree of freedom equations of motion by the transmission error excitation are derived. Using these equations, transfer matrix for the helical gear is derived. For the detail behavior of shaft motion, the $12{\times}12$ transfer matrix for the shaft is derived. Transfer matrix for the bearing, coupling, driving element, and load is also derived. Application of the boundary conditions in the assembled transfer matrix produces the forces and displacements in each element of the helical gear system. The effect of the proposed method is shown by numerical example.

• 디지털융복합연구
• /
• 제12권10호
• /
• pp.425-431
• /
• 2014

본 연구는 ATOM Phantom을 이용하여 선량, 화질을 비교 분석 하여 Volume mode의 유용성 밝혀 소아 CT 검사에 적극적으로 사용하기 위함이다. Helical mode Noise와 Volume mode의 Noise, HU, SNR은 p>0.05 이므로 통계적으로 유이한 차이가 없음을 알 수 있었다. 각 부위별 선량값은 모두 p>0.05 이므로 통계적 유이한 차이가 없었으나 DLP값이 Helical mode보다 Volume mode가 더 낮게 측정되었다. 유효선량 역시 Volume mode가 Helical mode 보다 낮음을 알 수 있었다. 정성적 분석에서는 Mode에 따른 조건 별로 각각 Helical: 2.6, 3.3, 4.36 Volume: 2.8, 3.64, 4.44, Mode별 Follow up 영상평가 결과로는 Helical mode가 3.8 Volume mode가 3.83점으로 큰 차이가 없는 것으로 나타났다. 5세 이하의 소아 CT검사에 있어서 640-MDCT Volume scan이 Helical mode와 비교해 낮은 선량으로 영상의 질이 큰 차이가 없기에 소아 CT 검사에는 유용 하다고 생각된다.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2007년도 추계학술대회논문집
• /
• pp.1042-1048
• /
• 2007

This work analytically investigated the radiated noise of a helical gear-housing system due to the excitation of helical gears. The helical gears were modeled as a 12-degree of freedom mass-spring-damper system; the shaft was modeled as a rod, a beam, and a torsional shaft; and the gear housing was modeled as a clamped circular plate with viscous damping. The modeling of this system used transfer matrices for helical gears, shafts, and bearings. Damping for both the bearings and the plate were obtained by modal testing. For the evaluation of noise, sound pressure from the plate due to the force and the moment in both radial and tangential directions was analytically derived by the Rayleigh integral. The analytical derivation and parameters from the experiment were applied to an analysis of noise for the two sets of helical gears with differing gear ratios. The analysis showed that the moment excitation in both helical gears contributed more to the noise of the plate than axial force excitation.

• 한국안전학회지
• /
• 제33권1호
• /
• pp.7-15
• /
• 2018

The friction factors according to the flow regimes in helical coil tubes depend on the coil diameter, the tube diameter, and the coil pitch. In previous studies, correlations for the laminar flow regime in helical coil tubes have been proposed. However, studies on the transition flow regime and the turbulent flow regime are insufficient and further researches are necessary. In this study, characteristics of the friction factors for the laminar, transition and turbulent flow regimes in helical coil tubes were experimentally investigated. The helical coil tubes used in the experiments were made of copper. The curvature ratios of the helical coil tubes, which means the ratio of helical coil diameter to inner diameter of the helical coil tube are 24.5 and 90.9. Experiments were carried out in the range of $529{\leq}Re{\leq}39,406$ to observe the flows from the laminar to the turbulent regime. The friction factors were obtained by measuring the differential pressures according to the flow rates in the helical coil tubes while varying the curvature ratios of the helical coil tubes. Experimental data show that the friction factors for the helical coil tube with 24.5 in the curvature ratio of the helical coil tube were larger than those in the straight tube in all flow regimes. As the curvature ratio of the helical coil tube increases, the friction factor in turbulent flow regime tends to be equal to that of the straight tube. In addition, it was confirmed that the transition flow regimes in the helical coil tubes were much wider than those in the straight tube, also the critical Reynolds numbers were larger than those in the straight tube. The results obtained in this experimental study can be used as basic data for studies on the water hammer phenomenon in helical coil tubes.

• 한국산학기술학회논문지
• /
• 제13권1호
• /
• pp.33-38
• /
• 2012

본 연구에서는 나선형 형태의 와이어를 자동차 무선통신(5.925GHz)용 차량 커넥터에 적용 가능성을 제안하였다. 이 나선형 와이어 형태의 커넥터 설계는 나선형 평균 반경, 나선형 피치, 나선형 와이어 자체의 반경, 나선형와이에서 접지 부분까지의 거리를 중요 설계인자로 판단하여 실시하였다. 이 같은 설계 해석 및 결과는 자동차 통신용 커넥터 설계를 위한 가장 적합한 나선형 와이어 치수 결정에 사용될 수 있을 것이다. 나선형 와이어가 삽입된 최적화된 자동차 WAVE용 커넥터는 삽입손실이 5.925GHz 대역에서 -0.76dB 이내로 발생되었다. 이 삽입손실 결과는 기존의 일반 커넥터에 비하여 21% 성능이 향상된 것이다. 따라서, 본 커넥터 해석결과는 자동차 통신을 위한 고주파대역의 최적 커넥터 설계에 유용하게 사용할 수 있을 것이다.

• 대한방사선기술학회지:방사선기술과학
• /
• 제20권1호
• /
• pp.15-20
• /
• 1997

Unlike conventional CT scan, the helical CT scan uses continuous rotating CT equipment with a slip ring to move the patient's coach at a constant speed while continuously scanning. Slice sensitivity profiles in the Z-position(SSPz) using the conventional X-ray CT have a shape similiar to a rectangular wave, which slightly spreads out into plains below the mountain. However, in the helical CT, with an expansion of the base, the rectangular shape collapses and a mouatain-like shape can be seen. We need to investigate the fellowing factors in helical CT scanning;the ability to scan along the axis of the body, effective slice width, slice shape and the precision of coach velocity, Helical scanning with sprial X-ray track is different from the conventional scanning in terms of the principle of image reconstruction performed. We believe that the problems in helical scanning can be solved by understanding new the special parameters such as the bed moving speed and the interval of image reconstruction.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2006년도 제37회 하계학술대회 논문집 B
• /
• pp.793-794
• /
• 2006

본 논문은 Slotless BLDC 모터를 고출력화 하기 위해서 나선형(Helical)방식을 적용하여 모터의 고출력화를 이루는 방식에 대한 연구이다. 기존의 SlotlessBLDC모터는 코깅이 없고, Slot이 없으므로 소형화에 유리한 장점을 지녔다. 반면에 공극의 자속 밀도가 낮아 출력을 높이는데 한계가 있었다. 따라서 본 논문에서는 기존의 SLBLDCM의 단점을 극복할 수 있는 Helical 방식을 제안하였다. Helical 방식을 적용할 때 기존의 인덕턴스 영향으로 인한 전류 확립에 한계가 있었으나 본 방식을 적용 시 높은 전류를 흘릴 수 있었으며 이로 인해 고출력화를 이룰 수 있었다. 아울러 Helical 방식을 취하므로 높은 전류로 인한 발열문제까지도 동시에 해결할 수 있는 장점이 있었다. 본 논문에서는 Helical 방식을 적용하여 기존대비 출력을 15%이상 향상시킬 수 있었으며, 온도 상승도 10%이상 억제할 수 있었다.

• 한국광학회:학술대회논문집
• /
• 한국광학회 2007년도 동계학술발표회 논문집
• /
• pp.151-152
• /
• 2007

In this study, the optical porosity of $TiO_2$ films with helical structure deposited by glancing angle deposition (GLAD) were investigated. Helical films are of interest due to their ability to differentiate states of circularly polarized light. We designed and fabricated normal-incidence circular-polarization separator deposited by GLAD (Helical structure). The optical porosity of $TiO_2$ film deposited by helical method can be applied many optical coatings.

• Journal of applied mathematics & informatics
• /
• 제26권3_4호
• /
• pp.445-456
• /
• 2008

We characterize the helical polynomial space curves and solve the first-order Hermite interpolation problem for helical polynomial space quintics.

• 한국정밀공학회지
• /
• 제18권9호
• /
• pp.165-170
• /
• 2001

In normal grinding abrasive particles of a grinding wheel rotate on planes parallel to the direction of workpiece fred. which may induce continued scratch lines on ground surface as the workpiece feeds. Instead in helical scan grinding the planes make an angle, called a helical angle, with the feeding direction. Thus scratch lines produced by abrasive particles per one revolution are discontinued which implies that the generation of scratch lines are suppressed by the helical scan grinding. In this study some experimental works have been done on the helical scan grinding of glass to find the effects of grinding conditions on the surface roughness and estimate the optimal grinding conditions. The helical angle, fred rate, material removal rate and the wheel speed are taken as factors for three kinds of grinding wheels i.e., coarse(#140 mesh), medium(#400) and fine(#800) diamond wheels. The experiments are scheduled by Taguchi technique and ANOVA has been carried out for the interpretation of the results. As a result of this study effects of the factors are verified quantitatively showing that the major factors are changed according to the wheel's mesh size and the helical angle is one of the influencing factors on the surface quality.