• 한국기계가공학회지
• /
• 제15권5호
• /
• pp.93-99
• /
• 2016

The trimming process is required for satisfying the dimensions of a final product in the hot stamping process. In general, the mechanical trimming or laser trimming process is applied after hot stamping. However, these processes have several disadvantages such as short tool life and low productivity. Therefore, in this study, the optimal trimless blank shape for the hot stamping process of a sill side was designed to remove the trimming process after hot stamping. In order to design the trimless blank, numerical analysis was performed. Firstly, CFD analysis was carried out to predict the cooling temperature and holding time of the hot stamping process. Then, the optimal trimless blank shape was determined through FE analysis. The effectiveness of the designed trimless blank shape was verified through a hot stamping experiment at an actual industrial site.

• 소성∙가공
• /
• 제24권1호
• /
• pp.13-19
• /
• 2015

For an accurate analysis of hot stamping, a coupled simulation with different aspects of the process(i.e. mechanical, thermal, and phase transformation) is needed. However, coupled simulations are time consuming and costly. Therefore, the current study proposes a simplified method focused on the forming for the hot stamping simulation of a coupled torsion beam axle (CTBA) tubular beam. In this simplified method, non-isothermal conditions were assumed and only conduction was considered, since it represents the majority of the heat transfer during hot stamping. In addition, temperature and strain rate effects were also included. Moreover, an isothermal simulation was conducted and compared with a non-isothermal simulation. Finally, the simulations were verified by experiments. In conclusion, the proposed method is shown to be effective for the development of tube-type parts, and it effectively predicts the deformation of the tubular beam during hot stamping.

• 열처리공학회지
• /
• 제35권2호
• /
• pp.66-73
• /
• 2022

Partial-hardened hot stamping has been well known to be very effective to absorb more energy in automotive lateral crash. Hardness distribution and dimensional change after partial-hardened hot stamping have been studied to find out effect of thermal deformation of the heated hot stamping die on dimensional accuracy of automotive center pillar. Soft zone of commercial center pillar showed 275~345 in Vickers hardness, indicating bigger non-uniformity which resulted from thermal deformation of heated die. Dimensional changes in soft zone of the commercial center pillar measured by three dimensional scanner were much bigger than that in hard zone. It has been found that hot stamping die compensation considering thermal deformation in soft zone causes a significant decrease in hardness deviation in the soft zone, corresponding to 20 percent of commercial center pillar and subsequently leads to much higher dimensional accuracy.

• Tribology and Lubricants
• /
• 제36권6호
• /
• pp.350-358
• /
• 2020

Hot stamping is an effective and suitable process widely used in automotive applications, though critical issues such as the transfer of the coating materials and build-up of these materials on tool surfaces have been encountered. Past researches figured out the resultant wear phenomenon using pin-on-disc and drawing (for example, strip drawing and deep drawing) methods to mimic the process and analyzed the wear behavior with respect to the influencing factors such as surface coating, load, and roughness. Although the pin-on-disc is a conventional and widely-used method, it presented a methodological limitation when simulating the hot stamping process by forming a new blank each time, and hence, a drawing-based friction method has been proposed and developed. Each drawing method applies loads in a different way, resulting in a different wear behavior. Notably, the deep drawing process is most similar to the hot stamping process compared to other drawing methods. In this paper we present a review of the friction testing methods mimicking the hot stamping process and the associated wear behavior. This can be helpful in presenting a step-by-step approach and different perspectives on the wear behavior in the hot stamping process.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2008년도 추계학술대회 논문집
• /
• pp.241-244
• /
• 2008

Automotive companies have conducted a study for light weigh body and crash safety. But It is difficult to adapt a mass production because of formability with high strength steel in the conventional stamping process. Recently, Automotive maker in the Europe, USA, Japan has applied a hot stamping with boron steel in the body structure. Hot stamping technology spread fast in various body parts of automobile. Bumper beam has been applied in the foreign automotive company so much nowadays. In this study, We will optimize crash performance of bumper beam using hot stamping through comparison with conventional bumper beam.

• 소성∙가공
• /
• 제30권5호
• /
• pp.242-246
• /
• 2021

Aluminum alloy sheet is being applied to automobiles continuously for the purpose of reducing car body weight. However, due to low formability, there's a limit to application of products with a deep forming depth such as door inner parts. Therefore, the difficult-to-form parts are mainly segmented formed then joined together, which is also disadvantageous as it increases the cost of manufacturing. This study proposes a hybrid cold-hot stamping method for the 1-piece door inner part to reduce cost. To design the stamping process, numerical simulation method is established by using the temperature-dependent mechanical properties of AA6016. The formability according to the hybrid cold-hot stamping method is evaluated using numerical analysis. The suitability of the proposed stamping method is then verified through the stamping tryout.

• 소성∙가공
• /
• 제32권3호
• /
• pp.160-165
• /
• 2023

As the supply of eco-friendly vehicles increases, the application rate of hot stamping components is rising to reduce vehicle weight and improve safety. Although Al-Si coated steel sheets are commonly used in hot stamping processes, their manufacturing costs are elevated due to process patents and royalties. Various hot stamping studies have been conducted to reduce these production costs. In this study, we derived a process control method for suppressing the oxide layer of hot stamping parts using uncoated boron steel sheets. Firstly, hat-shaped parts were hot stamped under atmospheric conditions to analyze the tendency of oxide layer formation by location. Then, the Gleeble system was used to observe oxide layer formation based on oxygen content under various atmospheric conditions. Finally, the oxide layer thickness was quantitatively measured using SEM images.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2008년도 추계학술대회A
• /
• pp.7-12
• /
• 2008

A hot stamping technology of vehicle door impact beam made of thin sheet steel has been developed, with the aim of ensuring occupant safety in a side collision. This technology has been implemented to increase the strength of vehicle body parts and to reduce not only the weight of door impact beam but also the number of work processes. Mechanical tests were performed to obtain material properties of hot-stamped specimen and those were used as input data in stamping and structural simulation for optimal design of door impact beam. Strength of hot-stamped door impact beam increased to the value 102% higher than that of conventional pipe-shaped door impact beam and structural simulation showed that hot-stamped door impact beam achieved 28% weight reduction.

• 소성∙가공
• /
• 제32권2호
• /
• pp.81-86
• /
• 2023

The hot stamping process is widely used for high strength of vehicle parts, with heating 900 ℃ or higher in a furnace and in-die quenching to achieve strength above 1.5 GPa of the quenchable boron alloyed steel 22MnB5. First of all, the hot stamping process consisted of heating, forming, quenching and trimming. In the trimming process case, the laser method has been conventionally adopted. For laser trimming process, it has the problems pertaining to low productivity and high cost while the hot stamping process, accordingly the trimming process need to investigate the research for alternative method. In order to overcome these issues, many research groups have studied the mechanical trim solution on the hot stamped parts at high temperature. In this study, the mechanical piercing was performed during the hot stamping process at the high temperature for overcome the disadvantages of laser cutting. Also, the process parameters such as piercing time after die closing, clearances of between die and punch were controlled for obtaining the reasonable shear characteristics.

• 한국정밀공학회지
• /
• 제28권1호
• /
• pp.63-72
• /
• 2011

In recent years, hot-stamped components are more increasingly used in the automotive industry in order to reduce weight and to improve the strength of vehicles. In hot stamping process, blank is hot formed and press hardened in a tool. However, in hot stamping without cooling channel, temperature of the tool increases gradually in mass production thus cannot meet the critical cooling rate to obtain high strength over 1500MPa. Warpage occurs in the hot stamped component due to non-uniform stress state caused by unbalanced cooling. Therefore, tools should be uniformly as well as rapidly cooled down by the coolant which flows through cooling channel. In this paper, optimal design method of cooling channel to obtain uniform and high strength of the component is proposed. Optimized cooling channel is applied to the hot press V-bending process. As a result of measuring strength, hardness and microstructure of the hot formed parts, it is known that the design methodology of cooling channel is effective to the hot stamping process.