• Journal of Advanced Marine Engineering and Technology
• /
• 제33권1호
• /
• pp.28-36
• /
• 2009

In this paper, based on the measured data of hull deflection, an approximated hull deflection curve is drawn using reverse analyzed hull deflection data and the estimation method for flexibility analysis of shaft alignment is proposed by use of the approximate hull deflection curve. Generally an offset value of after stern tube bearing is a datum point with an fore stern tube bearing however the shaft alignment has a tendency which is able to get higher flexibility if the shafting system has the deflection value from after stern tube bearing as reference to bottom direction according to results of on this study. By applying this result of study, the shaft alignment for next similar ships will be able to estimate how to follow the hull deflection and how to be influenced by hull deflection at shaft alignment analysis state using the approximated hull deflection curve.

• Journal of Advanced Marine Engineering and Technology
• /
• 제29권7호
• /
• pp.785-794
• /
• 2005

Modern ship hulls of large oil carriers and container carrers have become more flexible with scantling optimization and increase in ship length. On the other hand. as the demand for power has increased with the ship size. shaft diameters have become larger and stiffer. Consequently. the alignment of the propulsion system has become more sensitive to hull girder deflections. resulting in difficulties in analyzing the alignment and conducting the alignment procedure. Accordingly. the frequency of shaft alignment related bearing damages has increased significantly in recent years. The alignment related damages are mostly attributed to inadequate analyses. changes in the design of the vessel. shipyards' practices in conducting the alignment. and a lack of well defined analytical criteria. The hull deflections should be considered at the design stage to minimize the bearing damage caused by hull deflection. Hull deflections can be estimated by analytical approach and reverse calculation using the measured data. The hull girder deflection analysis using the reverse calculation will be introduced in this paper.

• Journal of Advanced Marine Engineering and Technology
• /
• 제30권7호
• /
• pp.800-807
• /
• 2006

This paper introduces the hull deflection analysis method by using the direct measurements. Accordingly, this paper demonstrates how the hull deflection data is obtained by the reverse calculations using the bending moments from the stain gauge and bearing reactions from jack-up method. Where the hull deflection data provided by this research is used for the shafting alignment calculations for identical or similar vessels, shafting failures due to hull deflections can be minimized. It will also save time and expenses associated finite element method to predict hull deflections.

• 대한조선학회논문집
• /
• 제43권4호
• /
• pp.512-520
• /
• 2006

The effects of flexibilities of supporting structures on shaft alignment are growing as ship sizes are Increasing mainly for container carrier and LNG carrier. But, most of classification societies not only do not suggest any quantitative guidelines about the flexibilities but also do not have shaft alignment design program considering the flexibility of supporting structures. A newly developed program, which is based on innovative shaft alignment technologies including nonlinear elastic multi-support bearing concept and hull deflection database approach, has S basic modules : 1)fully automated finite element generation module, 2) hull deflection database and it's mapping module on bearings, 3) squeezing and oil film pressure calculation module, 4) optimization module and 5) gap & sag calculation module. First module can generate finite element model including shafts, bearings, bearing seats, hull and engine housing without any misalignment of nodes. Hull deflection database module has built-in absolute deflection data for various ship types, sizes and loading conditions and imposes the transformed relative deflection data on shafting system. The squeezing of lining material and oil film pressures, which are relatively solved by Hertz contact theory and built-in hydrodynamic engine, can be calculated and visualized by pressure calculation module. One of the most representative capabilities is an optimization module based on both DOE and Hooke-Jeeves algorithm.

• Journal of Advanced Marine Engineering and Technology
• /
• 제23권4호
• /
• pp.565-573
• /
• 1999

Hihg Tensile Steel enables to reduce the plate thickness comparing to the case when Mild Steel is used. From the economical view points this is very preferable since the reduction in the hull weight. however to use the High Tensile Steel effectively the plate thickness may become thin so that the occurrence of buckling is inevitable and design allowing plate buckling may be necessary. If the inplane stiffness of the plating decreases due to buckling the flexural rigidity of the cross sect6ion of a ship's hull also decreases. This may lead to excessive deflection of the hull girder under longitudinal bending. In these cases a precise estimation of plate's behavior after buckling is necessary and nonliner analysis of isolated and stiffened plates is required for structural sys-tem analysis. In this connection this paper discusses nonlinear behaviour of thin plate under thrust. Based on the analytical method elastic large deflection analysis of isolated plate is perform and simple expression are derived to evaluated the inplane rigidity of plates subjected to uniaxial compression.

• 한국항해학회지
• /
• 제8권2호
• /
• pp.43-50
• /
• 1984

When the static load is applied to the ship's hull the deflection due to the bending moment from longitudinal direction has not been considered in the usual calculation of maximum bending moment. In fact, however, the deflection of ship's hull must be affected by the above-stated bending moment, and in this case the value of the maximum bending moment would be lessened in comparision with the result of usual calculation. In this paper, the author at first calculated the difference between the two values in case of rectangular barge, and suggested a practical criterion of longitudinal strength.

• 대한조선학회지
• /
• 제23권3호
• /
• pp.27-38
• /
• 1986

In the recent years, the finite element method has been a leading method in calculating the strength of ship hull structural members. But such a calculation has many difficulties in constructing data, reducing CPU-time and connecting it with optimal design. This paper describes more efficient method for three dimensional strength calculation of the hull structure of oil tanker by using the slope-deflection method, and the computer program based on this method is developed. The results of the calculation by using this method are compared with those by using the SAP4 program based on the finite element method. Some advantages are obtained from the application of the slop-deflection method described in this paper in the calculation of the hull structure oil tanker.

• 대한조선학회논문집
• /
• 제37권1호
• /
• pp.118-126
• /
• 2000

저자들에 의해 기 제안한 바 있는 일반화 경사처짐법을 이용하여 이중 선각 유조선의 최적 구조 설계 시스템을 개발하였다. 최적화 기법으로는 직접탐색법의 일종인 Hooke와 Jeeves 방법을 사용하여 이산화변수를 용이하게 처리할 수 있도록 하였다. 일반화 경사처짐법과 최적화 기법을 결합하여 선급규정에 의한 종강도 부재의 최소 중량 설계프로그램과 일반화 경사처짐법에 의한 횡강도 부재 및 횡격벽 부재의 최소 중량 설계 프로그램을 개발하였다. 개발한 프로그램을 이용하여 tank 배치를 고려한 이중 선각 유조선의 최적 구조 설계를 수행하여 실적선의 설계 치수 및 선각 중량과 비교하였으며, 최소 중량을 주는 tank 배치와 tank type을 결정할 수 있었다.

• 대한조선학회 특별논문집
• /
• 대한조선학회 2007년도 특별논문집
• /
• pp.1-6
• /
• 2007

To improve productivity of the LNG carriers which are growing bigger and bigger, many researches are being carried out by shipyards. In this regard, we reviewed possible problems which could occur during the erection of 216K LNG carrier's motor/compressor room with all outfittings pre-installed. As a first item, the weights of hull and outfittings were precisely estimated to make sure that the erection is carried out within yard's capability. In the next place, deflection and safety of the structure were verified by FEM analysis. As a result, the erection was finished successfully and yard's productivity was also improved. This review is a good example which shows the importance of through study and preparation for improving yard's productivity which is already reached its limit.

• 한국항해항만학회:학술대회논문집
• /
• 한국항해항만학회 1996년도 The Korean Institute of Navigation 1996년도 한·중 국제학술 심포지움 및 추계학술발표회 논문집
• /
• pp.95-110
• /
• 1996

High Tensile Steel enables to reduce the plate thickness comparing to the case when Mild Steel is used. From the economical view point this is very preferable since the reduction in the hull weight. However to use the High Tensile Steel effectively the plate thickness may become thin so that the occurrence of buckling is inevitable and design allowing plate buckling may be necessary. If the inplane stiffness of the plating decreases due to buckling, buckling may be necessary. If the inplane stiffness of the plating decreases due to buckling the flexural rigidity of the cross section of a ship's hull also decreases. this may lead to excessive deflection of the hull girder under longitudinal bending. In these cases a precise estimation of plate's behavior after buckling is necessary and nonlinear analysis of isolated and stiffened plates is required for structural system analysis. In this connection this paper discusses nonlinear behaviour of thin plate under thrust. Based on the analytical method elastic large deflection analysis of isolated plate is perform and simple expression are derived to evaluate the inplane rigidity of plates subjected to uniaxial compression.