• The Journal of the Korea institute of electronic communication sciences
• /
• v.9 no.3
• /
• pp.335-342
• /
• 2014

In this paper We study on test methods and procedures for Hybrid Track Circuit's practicalization. It's possible to apply to HTC's Seoulmetro and high-speed train by proposing test method considering special rail environment and RFID tag and leader, antenna We also present the test methods and procedures for safe and reliable of interface among the Hybrid track circuit devices.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.8 no.3
• /
• pp.471-477
• /
• 2013

We have studied on the possibility of precise positioning using hybrid Track Circuit system. Hybrid Track Circuit uses RFID which replaces UHF. Hybrid Track Circuit is a part of next generation railroad signal system which is available to communicate with a railway on board system based on a realtime operating system. If applicate on a current hand operating subway, phenomenon caused by driver's mistake such as passing a stop without stopping or mismatch error between PSD and train door should be prevented.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.9 no.4
• /
• pp.537-542
• /
• 2014

Track circuit is a simple electrical device which lies in the connection of the two rails by the wheels and axle of locomotives and rolling stock to short out an electrical circuit, used to detect the absence of a train on rail tracks. In railway signaling system, there are similar systems such as RFID and wheel sensor, GPS etc, are research and developing. Hybrid track circuit is using RFID antenna and reader on the cab and RFID tag on the sleeper. because of the safety in railway operation, tag detection of train position detection function in the hybrid track circuit needs high reliability. This paper studied tag recognition enhancement used tag angles.

• Journal of Electrical Engineering and Technology
• /
• v.12 no.2
• /
• pp.790-802
• /
• 2017

This paper proposes the modeling and control strategy to track the MPPs of hybrid PV and Wind power systems, using a new dual input boost converter. The dual input power conditioning system with an independent MPPT control scheme is introduced with minimum number of circuit elements in order to reduce the switching loss, size and cost of the system. Since the operating conditions for the PV and Wind power systems are very distinct from each other, an efficient and superior control system is required to track the MPPs of both renewable sources with the use of a simply-structured single-ended single-inductor converter. The design of Power-Conditioning System (PCS) and detail control strategy are presented in this paper. To provide independent tracking of MPPs, a variable duty-cycle control strategy is employed for the wind system and a variable frequency strategy is employed for the PV system. Finally, the proposed dual-input converter for hybrid power conditioning system is implemented and the hardware test results are presented. From the hardware experiment, it is concluded that the proposed system successfully tracks the MPPs of both of the renewable power systems independently.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.11b
• /
• pp.782-787
• /
• 2002

In optical disk drives (ODD), the demands of high data density and high speed have been increasing rapidly to achieve high data capacity and data transfer rate. The short wavelength laser, High NA objective lens, and high track following performance are needed to raise data density and data rate. For high-performance actuator, the improvement of linearity and acceleration become more important. Also, 3-axis actuator for active tilt compensation is introduced to overcome the decrease in disk tilt tolerance which is induced by short wavelength laser. In this paper, a hybrid type 3-axis actuator is presented and a new yoke structure, which can reduce the interaction between yoke and moving magnet, is designed to keep the efficiency of magnetic circuit. Experimental results show the validity of the yoke in the hybrid type actuator.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.9 no.2
• /
• pp.249-254
• /
• 2014

We have studied on the possibility of railway stability system using RFID tag. UHF RFID tag was desinged, manufactured and tested. Proposed UHF tag antenna has PIFA type structure and inset feed multi matching technique was attempted for impedance matching of antenna. The impedance bandwidth (VSWR < 3) of the proposed tag antenna covers 917~923 MHz. Measured peak gain is 3.225 dBi and UHF band with an omni-directional radiation pattern. RFID reader and tag installed in motor car and track, respectively. Then, tag recognition rate according to velocity of car (under 45 km/h) represented 100 %.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.29 no.4 s.235
• /
• pp.624-631
• /
• 2005

A note-book PC has become thinner in recent years, which requires the optical disc drives with small height and high memory capacity. Therefore the actuator of optical disc drives must be thinner and have disc tilt compensation function for high density memory. In this paper, the actuator with hybrid type is investigated for 3-axis ultra-slim actuator. A 3-axis ultra-slim actuator is designed by using the modal analysis of the actuator and the electromagnetic analysis of magnetic circuit to achieve dynamic characteristics. Also, magnetic force between tilt magnet and tilt yoke is investigated to and the influence on the DC sensitivity in the focus and track directions.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2003.11a
• /
• pp.208-213
• /
• 2003

A note-book PC has become thinner in recent years. And optical disc drives are required to have high memory capacity. Therefore, the actuator of optical disc drives must be thinner and have disc tilt compensation function for high density memory. In this paper, the hybrid type actuator is investigated for 3-axis ultra-slim actuator. A 3-axis ultra-slim actuator is designed by using the modal analysis of the actuator and the electromagnetic analysis of magnetic circuit to achieve dynamic characteristics and magnetic flux density for high sensitivity, respectively. Also, magnetic force between tilt magnet and tilt yoke is investigated to find the influence on the DC sensitivity in the focus and track directions.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.63 no.4
• /
• pp.226-235
• /
• 2014

Nowadays, railroads are considered the most efficient form of mass transportation. Furthermore, it is necessary that railroads be paired with state-of-the-art safety equipment. Unfortunately, it is impossible to prevent 100% of accidents that may be caused by system or human errors. In order to prevent future accidents, RAMS activity and Functional Safety Certification are required for new systems that are under development. In this paper we evaluate the necessity of the application of RAMS and the performance of RAMS in the system development process. We also explore the Safety Evaluation Procedure required for RAMS certification.