• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.44 no.7 s.361
• /
• pp.37-44
• /
• 2007

A low-voltage high-linear bipolar OTA and its application to IF bandpass filter for GSM cellular telephone are presented. The OTA consists of a low-voltage linear transconductor, a translinear current gain cell, and three current mirrors. The bandpass filter is composed of two cascaded identical second-order bandpass filters, which consist of a resistor, a capacitor, and a grounded simulated inductor realized with two OTA's and a grounded capacitor. SPICE simulations using an 8 GHz bipolar transistor-array parameter show that the OTA with a transconductance of 1 mS exhibits a linearity error of less than ${\pm}2%$ over an input voltage range of ${\pm}0.65\;V$ at supply voltages of ${\pm}2.0\;V$. Temperature coefficient of the transconductance is less than $-90ppm/^{\circ}C$. The bandpass filter has a center frequency of 85 MHz and Q-factor of 80. Temperature coefficient of the center frequency is less than $-182ppm/^{\circ}C$. The power dissipation of the filter is 128 mW.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.44 no.10
• /
• pp.17-22
• /
• 2007

This paper presents a baseband complex bandpass filter for PHS applications with a new automatic tuning method. The full-CMOS PHS transceiver is implemented by adopting the Low-IF architecture to overcome the DCoffset problems. To meet the Adjacent Channel Selectivity (ACS) performance, the 3rd-order Chebyshev complex bandpass filter is designed as the baseband channel-select filter. The new corner frequency tuning method is proposed to compensate the process variation. This method can reduce the noise level due to MOS switches. The filter was fabricated using a 0.35{\mu}m$ CMOS process, and the power consumption is 12mW.

• Journal of electromagnetic engineering and science
• /
• v.8 no.2
• /
• pp.76-83
• /
• 2008

A low power(9 mW) highly-digitized 2.4 GHz receiver for sensor network applications(IEEE 802.15.4 LR-WPAN) is realized by a $0.18{\mu}m$ CMOS process. We adopted a novel receiver architecture adding an intermediate frequency (IF) level detection scheme to a low-power complex fifth-order continuous-time(CT) bandpass L:tl modulator in order to digitalize the receiver. By the continuous-time bandpass architecture, the proposed $\Sigma\Delta$ modulator requires no additional anti-aliasing filter in front of the modulator. Using the IF detector, the achieved dynamic range(DR) of the over-all system is 95 dB at a sampling rate of 64 MHz. This modulator has a bandwidth of 2 MHz centered at 2 MHz. The power consumption of this receiver is 9.0 mW with a 1.8 V power supply.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.33A no.11
• /
• pp.70-77
• /
• 1996

In this paper, a modifed TE$_{113}$/TM$_{012}$ triple-mode bandpass filter is implemented by using a modified inter-cavity iris in which the number of slots are reduced upto 50%. In a coventioanl iris two prirs of slot apertures are used to independently couple three resonant modes between two adjacent cavities. However, if transverse magnetic polarizability of a pair of veritcal slot apertures is used to control weak horizontal TE$_{h}$-TE$_{h}$ mode coupling, the width of novel iris slots would substitute for the slot length of the conventional iris, causing to eliminate the horizontal slot apertures. The measured data of two filters, which are the modified filter and ocnventional one, are compared. Experimental result shows that the characteristics of the novel triple-mode filter matches well that of the conventional filter.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2012.10a
• /
• pp.69-72
• /
• 2012

In the bandpass sampling(BPS), the sampling frequency is lower than the frequency of the RF(radio frequency) signal being sampled. In this method, the baseband spectrum directly appears by the sampling itself, so that it is not necessary to use any down converter, making the receiver's hardware simpler. The second-order BPS uses two identical BPS samplers operating with an offset timing to each other. By a processing with their two sampled signals, it can be possible to cancel the aliasing or interference component if any due to the bandpass sampling. The interpolant filter, which is to manipulate the phase characteristics of the sampled signal, affects the performance of the cancellation. In this paper, a multiband interpolant filter is introduced, with which multiple interference signals from multiple RF bands can be cancelled simultaneously. We suggest several phase characteristics for the interpolant filter and have evaluated their performances through computer simulations. It has been shown that the filter with a continuous phase function gives the better performance.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.11 no.4
• /
• pp.1-8
• /
• 2011

In this paper, a microstrip bandpass filter(BPF) with 3 dB bandwidth of more than 50 % at center frequency of 30 GHz was implemented. The implemented BPF is to be used as ASK(Amplitude Shift Keying) transmission and reception filters in IF band for THz transmitter and receiver capable of 10 Gb/s wireless data transmission. The microstrip BPF with ultra-wideband characteristics was implemented using a stepped-impedance lowpass filter(LPF) and a composite quarter-wave short stubs where the LPF is functioning as attenuating the upper stopband and quarter-wave short stubs is functioning as attenuating the lower stopband. The measured results are as follows; the insertion loss is 0.65 dB at 30 GHz, the stopband characteristics are -10 dB and -16 dB at 10 GHz and 50 GHz, respectively, and the passband flatness is ${\pm}0.5$ dB at 20~40 GHz.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.13 no.4
• /
• pp.152-159
• /
• 2005

The method of induction noise reduction can be classified by using passive control or active control method. However, the passive control method has a demerit to reduce the effect of noise reduction to low frequency (below) 500Hz) range and to be limited in a space of the engine room. Whereas, the active control method can overcome the demerit of passive control method. The algorithm of active control is mostly used in LMS (Least-Mean-Square) algorithm because it can obtain the complex transfer function easily in real-time. Especially, Filtered-X LMS (FXLMS) algorithm is applied to an ANC system. However, the convergence performance of LMS algorithm could not match if the FXLMS algorithm is applied to an active control of the induction noise under rapidly accelerated driving conditions. So, in order to solve the problem in this study, the Moving Bandpass Filter(MBPF) was proposed and implemented. The ANC using MBPF for the reduction of the induction noise shows that more noise reduction as 4dB than without MBPF.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.13 no.6
• /
• pp.483-488
• /
• 2020

In recent years, the demand for wireless devices incorporating several wireless communication systems into one has been increasing in order to provide services that meet the diverse needs of consumers. Wireless devices consisting of various wireless communication systems require many frequency fixed filters. A frequency tunable filter can replace a number of frequency fixed filters in the wireless devices. If a frequency tunable filter is used in wireless systems, the system can be configured more efficiently. In this paper, a 3-pole frequency tunable BPF(bandpass filter) operating in the frequency band of 800 ~ 2400MHz is designed. In order to widen the operating frequency band, a tuning screw is designed to have a step and a linear motor is used to facilitate the adjustment of the tuning screw. The implemented frequency tunable BPF operates in the designed frequency range and has the maximum insertion loss of 2.82dB in the channel band and the minimum attenuation of 18.7dB at ± 50MHz frequency offset from the center frequency of the band.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.44 no.8
• /
• pp.1-7
• /
• 2007

Class AB bipolar linear transconductors for high frequency applications ire proposed. They consist of a voltage follower, a resistor, and a current follower. The follower circuits are realized by translinear cells or unity-gain buffers. The proposed transconductors are simulated using an 8 GHz bipolar transistor-arrary parameter. Simulation results show that the transconductor using translinear cells has better linearity than one using unity-gain buffers whereas the latter has better temperature stability and higher input resistance than the former. In order to test their high frequency applicability, the transconductors are used to implement an 4th order IF bandpass filter.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.47 no.11
• /
• pp.84-90
• /
• 2010

In this paper, the reduced size of broad bandpass filter with parallel coupled line structure is presented. This proposed filter can control bandwidth of narrow to broadband by adjusting the coupling coefficient. The conventional filter is operated with a narrow band. If a higher bandwidth is desired than the conventional narrow bandwidth, it is hard to realize due to the coupling coefficient between feeding line and resonator. In this paper, to overcome this limitation, a proposed bandpass filter is designed with reduced size due to SIR(Stepped Impedance Resonator) and multi-grade type structures than conventional one, and it has characteristics of adjusting bandwidth freely as per quantity of coupling coefficient. The proposed bandpass filter that, experimental results of insertion and return losses are 0.42 dB and 20.9 dB with bandwidth of 60 % at the center frequency of 5.8 GHz, respectively.