• Polymer(Korea)
• /
• v.37 no.1
• /
• pp.61-65
• /
• 2013

In this work, the anodic oxidation of carbon fibers was carried out to enhance the mechanical interfacial properties of carbon fibers-reinforced epoxy matrix composites. The surface characteristics of the carbon fibers were studied by FTIR, X-ray photoelectron spectroscopy (XPS), and scanning electron microscopy (SEM). Also, the mechanical interfacial properties of the composites were studied with interlaminar shear strength (ILSS), critical stress intensity factor ($K_{IC}$), and critical strain energy release rate ($G_{IC}$). The anodic oxidation led to a significant change in the surface characteristics of the carbon fibers. The anodic oxidation of carbon fiber improved the mechanical interfacial properties, such as ILSS, $K_{IC}$, and $G_{IC}$ of the composites. The mechanical interfacial properties of the composites anodized at 20% sulfuric/nitric (3/1) were the highest values among the anodized carbon fibers. These results were attributed to the increase of the degree of adhesion at interfaces between the carbon fibers and the matrix resins in the composite systems.

• Carbon letters
• /
• v.4 no.2
• /
• pp.69-73
• /
• 2003

In this work, the effect of a direct oxyfluorination on surface and mechanical interfacial properties of PAN-based carbon fibers is investigated. The changes of surface functional groups and chemical composition of the oxyfluorinated carbon fibers are determined by FT-IR and XPS measurements, respectively. ILSS of the composites is also studied in terms of oxyfluorination conditions. As a result, FT-IR exhibits that the carboxyl/ester groups (C=O) at 1632 $cm^{-1} and hydroxyl group (O-H) at 3450 $cm^{-1} are observed in the oxyfluorinated carbon fibers. Especially, the oxyfluorinated carbon fibers have a higher O-H peak intensity than that of the fluorinated ones. XPS result also shows that the surface functional groups, including C-O, C=O, HO-C=O, and C-$F_x$ after oxyfluorination are formed on the carbon fiber surfaces, which are more efficient and reactive to undergo an interfacial reaction to matrix materials. Moreover, the formation of C-$F_x$ physical bonding of the carbon fibers with fluorine increases the surface polarity of the fibers, resulting in increasing ILSS of the composites. This is probably due to the improvement of interfacial adhesion between fibers and matrix resins.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2004.10a
• /
• pp.100-103
• /
• 2004

In this work, the effects of oxy-fluorination on surface characteristics of carbon fibers were investigated in mechanical interfacial properties of carbon fibers-reinforced composites. The surface properties of the carbon fibers were determined by X-ray photoelectron spectroscopy (XPS), FT-IR. and contact angle measurements. And their mechanical interfacial properties of the composites were studied in interlaminar shear strength (ILSS) and critical stress intensity factor $(K_{IC})$. As experimental results, the $F_{1S}/C_{1S}$ ratio of carbon fiber surfaces was increased by oxy-fluorination, due to the development of the oxygen containing functional groups. The mechanical interfacial properties of the composites, including ILSS and $K_{IC}$, had been improved in the oxy-fluorination on fibers. These results could be explained that the oxy-fluorination was resulted in the increase of the adhesion between fibers and matrix in a composite system.

• Korean Journal of Materials Research
• /
• v.5 no.8
• /
• pp.979-987
• /
• 1995

This study has been investigated the Influence of layer thickness on the mechanical properties of cross laminated carbon fiber/epoxy composites. And also the difference of mechanical properties between cross laminated composites of unidirectional prepreg and fabric prepreg has been investigated. Experimental results are showed that the Interlamina Shear Strength(ILSS) of cross laminated carbon fiber/epoxy composites decreased with increasing thickness of unit ply and the decree of delamination in the laminated composites increased as ILSS decreased. Fracture toughness and impact values were found to increase as delamination occurs to some extent in the laminated composites. It Is also shown thats mechanical properties of cross laminates from unidirectional prepreg were better than those of cross laminates from fabric prepreg.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 1999.11a
• /
• pp.118-123
• /
• 1999

저밀도 폐놀계 탄소/탄소 복합재의 층간전단강도를 개선하기 위해 흑연분말, 카본블랙, 카본매트, 단섬유 등의 첨가제를 사용하였다. 카본매트와 단섬유를 첨가한 경우, 수지의 부족에 의한 층간접착력의 약화를 가져왔으며, 카본블랙을 첨가한 경우에도 큰 효과를 나타내지 못했다. 흑연을 첨가했을 때 약 30%의 층간강도 개선을 가져왔으며 특히 9 vol.%의 첨가량에 대해서 가장 큰 효과를 보였다.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 1999.11a
• /
• pp.40-43
• /
• 1999

Electrochemical surface treatment of PAN-based carbon fibers in acidic electrolyte has been studied in increasing the surface functional groups on fiber surfaces for the improvement of fiber-matrix adhesion of the resulting composites. According to the FT-IR and XPS measurements, it reveals that the oxygen functional groups on fibers are largely influence on the composite mechanical behaviors, whereas the nitrogen functional groups are not affected in the system. In this work, a good correlation between surface functionality and mechanical properties is established.

• Composites Research
• /
• v.15 no.6
• /
• pp.16-23
• /
• 2002

In this work, the effect of anodic oxidation on surface characteristics of high strength PAN-based carbon fibers was investigated in mechanical interfacial properties of composites. The surface properties of the carbon fibers were determined by acid-base values, scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS), and contact angles. And their mechanical interfacial properties of the composites were studied in interlaminar shear strength (ILSS) and critical stress intensity factor ($K_{IC}$). As a result, the acidity or the $O_{ls}/C_{ls}$ ratio of carbon fiber surfaces was increased, due to the development of the oxygen functional groups. Consequently, the anodic oxidation led to an increase in surface free energy of the carbon fibers, mainly due to the increase of its specific (or polar) component. The mechanical interfacial properties of the composites, including ILSS and $K_{IC}$, had been improved in the anodic oxidation on fibers. These results were explained that good wetting played an important role in improving the degree of adhesion at interfaces between fibers and epoxy resin matrix.

• Journal of Adhesion and Interface
• /
• v.14 no.2
• /
• pp.75-81
• /
• 2013

Epoxy matrix based composites were fabricated by adding SiC nano fillers. The interfacial properties of composites were varied with different shapes of SiC nano fillers. To investigate the shape effects on the interfacial properties, beta and whisker type SiC nano fillers were used for this evaluation. The dispersion states of nano SiC-epoxy nanocomposites were evaluated by capacitance measurements. FE-SEM was used to observe the fracture surface of different structures of SiC-epoxy nanocomposites and to investigate for reinforcement effect. Interfacial properties between carbon fiber and SiC-epoxy nanocomposites were also evaluated by ILSS (interlaminar shear strength) and IFSS (interfacial shear strength) tests. The interfacial adhesion of beta type nanocomposites was better than whisker type.

• Polymer(Korea)
• /
• v.39 no.2
• /
• pp.219-224
• /
• 2015

In this work, the effect of fiber array direction including $0^{\circ}$, $0^{\circ}/90^{\circ}$, $0^{\circ}/45^{\circ}/-45^{\circ}$ was investigated for mechanical properties of basalt fiber-reinforced composites. Mechanical properties of the composites were studied using interlaminar shear strength (ILSS) and critical stress intensity factor ($K_{IC}$) measurements. The cross-section morphologies of basalt fiber-reinforced epoxy composites were observed by scanning electron microscope (SEM). Also, the surface properties of basalt fibers were determined by Fourier transform infrared spectroscopy (FTIR) and X-ray photoelectron spectroscopy (XPS). From the results, it was observed that acid treated basalt fiber-reinforced composites showed significantly higher mechanical interfacial properties than those of untreated basalt fiber-reinforced composites. These results indicated that the hydroxyl functional groups of basalt fibers lead to the improvement of the mechanical interfacial properties of basalt fibers/epoxy composites in the all array direction.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2004.04a
• /
• pp.182-185
• /
• 2004

In this work, the effect of chemical treatments on surface properties of SiC was investigated in mechanical interfacial properties of carbon fibers-reinforced composites. The surface properties of the SiC were determined by acid/base values and contact angles. The thermal stabilities of carbon fibers-reinforced composites were investigated by thermogravimetric analysis (TGA). Also, the mechanical interfacial properties of the composites were studied in interlaminar shear strength (ILSS) and critical strain energy release rate mode II $(G_{IIC})$ measurements. As a result, tile acidically treated SiC (A-SiC) had higher acid value than that of untreated SiC (V-SiC) or basically treated SiC (B-SiC). According to the contact angle measurements, it was observed that chemical treatments led to an increase of surface free energy of the SiC surfaces, mainly due to the increase of the specific (polar) component. The mechanical interfacial properties of the composites, including ILSS and $(G_{IIC})$, had been improved in the specimens treated by chemical solutions. These results were explained that good wetting played an important role in improving the degree of adhesion at interfaces between SiC and epoxy resin matrix.