• Journal of Institute of Control, Robotics and Systems
• /
• v.18 no.3
• /
• pp.230-236
• /
• 2012

Shielding the air-gap magnetic field of the electrodynamic wheel below a conductive plate and opening the shielding plate partially, a thrust force and a normal force generate on the conductive plate at the open area. But, as only the variable controlling both forces is a rotating speed of the electrodynamic wheel, it is very difficult to control the forces independently by the speed. So, we discuss a novel method controlling the forces effectively through manipulating a size of the open area. The independent control is made possible by virtue of the feature that the relative ratio between both forces is irrelevant to an air-gap length and determined uniquely for a specific rotating speed of the wheel. Therefore, the rotating speed and the size of open area become new control variables. The feasibility of the method is verified experimentally. Specially, the controllable magnetic forces are used in a noncontact conveyance of the conductive plate.

• Applied Chemistry for Engineering
• /
• v.7 no.6
• /
• pp.1147-1155
• /
• 1996

In the spray drying with rotating wheel atomizer of cheese powder, the relationships among variables were analyzed with Response Surface Methodology in which several independent variables such as total solid content, wheel rotation speed, and outlet temperature influenced dependent variables such as particle diameter, moisture content, bulk density, and viscosity of suspended liquid. Significance and correlation were tested according to central composite design. As a results of analyzing the correlations between independent and dependent variables, particle diameter and moisture content of cheese powder were decreased with increasing wheel rotation speed, and bulk density was decreased with increasing outlet temperature. Viscosity of suspended liquid were increased with increasing wheel rotation speed and total moisture content. In correlation among dependent variables, moisture content was proportional to bulk density, and particle diameter was inversly proportional to moisture content and bulk density.

• Journal of Institute of Convergence Technology
• /
• v.6 no.2
• /
• pp.1-7
• /
• 2016

The rotating electrodynamic wheels can produce three-axial forces on the conductive target. The forces are linked strongly each other, and their magnitudes depend on the rotating speed of the wheel. However, the wheels can be used effectively as an actuating principle for transfer system of conductive material. The conductive material is a pipe with a constant cross-section or a conductive plate. In this paper, a few applications using the electrodynamic wheels as transferring means are introduced including the full description of the real hardware implementation.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.22 no.6
• /
• pp.1010-1017
• /
• 2013

Two-axial electrodynamic forces generated on a conductive plate by a partially shielded magnet wheel are strongly coupled through the rotational speed of the wheel. To control the spatial position of the plate using magnet wheels, the forces should be handled independently. Thus, three methods are proposed in this paper. First, considering that a relative ratio between two forces is independent of the length of the air-gap from the top of the wheel, it is possible to indirectly control the in-plane position of the plate using only the normal forces. In doing so, the control inputs for in-plane motion are converted into the target positions for out-of-plane motion. Second, the tangential direction of the open area of the shield plate and the rotational speed of the wheel become the new control variables. Third, the absolute magnitude of the open area is varied, instead of rotating the open area. The forces are determined simply by using a linear controller, and the relative ratio between the forces creates a unique wheel speed. The above methods were verified experimentally.

• Journal of the Korean Society for Railway
• /
• v.17 no.1
• /
• pp.28-34
• /
• 2014

In this paper, a concept design of a rail type ultra-high-speed train is proposed and its dynamic characteristics are analyzed. Instead of the existing solid axle, a new type bogie system and independently rotating wheels are applied in the proposed train. In order to analyze the dynamic characteristics, a multibody dynamic model of a vehicle is developed and the basic validity is verified by eigenvalue analysis. Also, it is shown that the critical speed is improved in comparison to that of existing high-speed train model HEMU-430X. Finally, through 7000R curved track driving analysis at a speed of 550 km/h, the lateral force of the wheels and the derailment quotient are estimated and the applicability of the new concept railway vehicle is confirmed.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.7
• /
• pp.275-282
• /
• 2018

Mountain trams are an environmental-friendly transportation system that run wirelessly on an embedded track constructed on previous mountain roads, and can run despite the frozen road. On the other hand, there is some difficulty on sharp and steep tracks. In this study, after possible technical problems were defined in mountain trams running on a sharp and steep track, the design solutions for the interface structure of bogie and carbody were proposed. In addition, a prototype was made and its performance was tested to verify the solutions. Because the difference in the distance of the inner and outer rails on a sharp curve is severe enough to interrupt running, independent rotating wheels with different angular speeds were developed and applied. To prevent derailment due to the large attack angle and lateral force caused by the previous vehicle of 2bogie-and-1carbody on the sharp curve, a vehicle with 1bogie-and-1carbody was designed and applied. A prototype vehicle of 1bogie-and-1carbody with independent rotating wheels was made to improve the performance during the test running on a small track. A coupler was designed to absorb the large rotations of 3 degrees-of-freedom between the carbodies of a mountain tram running on the steep curved track. After a small scale prototype was made, the performance was verified by a function test.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.9
• /
• pp.493-501
• /
• 2016

In this study, core technologies of a traction system on a mountain tram operating on the track of mountain road full of sharp curves and steep gradients were developed. In domestic mountain resort areas, sometimes the transportation service is not provided in winter because of ice and heavy snow on roads, so a mountain railway service independent of the climate and geographic conditions is needed. A traction system was designed taking into account of the power of a traction motor to climb the gradient of 120 ‰, which is common in domestic mountainous areas. and power transmission system was designed to consider the installation space for the traction system. In addition, a reduction gear and a propeller shaft were developed. An elastic pinion was developed and applied to the rack & pinion bogie system for steep gradient so that noise and vibration generated by contact between the steel gears could be reduced. Impact comparison tests showed that the vibration level of the elastic pinion is one-third lower than that of previous steel pinion. Independent rotating wheels and axles were developed for the bogie system to operate on the sharp curve of a 10 meter radius. In addition, the band braking system was developed to enhance the braking force during running on the steep gradient. A test for the braking force showed it exerts the required braking force. The performance of the developed core components were verified by the tests and finally they were applied to the bogie system running on the track of steep gradient and sharp curve.

• The Bulletin of The Korean Astronomical Society
• /
• v.38 no.2
• /
• pp.83.2-83.2
• /
• 2013

Camera for QUasars in EArly uNiverse (CQUEAN) is an optical CCD camera developed by the Center for the Exploration of the Origin of the Universe (CEOU). In 2010 August, CQUEAN was attached on the 2.1m Otto Struve Telescope at the McDonald Observatory in Texas, USA. As the main purpose of CQUEAN is detecting the Lyman breaks of redshift ~5 quasars, it is sensitive to near-infrared wavelengths (0.7-1.0 ${\mu}m$). For the auto-guiding system, it is using a rotating guide arm to find guide stars on the Cassegrain off-axis focus of the telescope. We plan to upgrade a new filter wheel system consists of a series of narrow band filters. We will install this independent auto-guiding units on the finder scope, which makes rooms on the Cassegrain focal plane of the main telescope. In this presentation we present the system architecture of the CQUEAN Auto-guiding Package (CAP).