• Proceedings of the KIEE Conference
• /
• 1993.07b
• /
• pp.1095-1097
• /
• 1993

The double excited induction motor has two sets of three-phase system : One is connected to the ac source to take care of energy convertion, and the other is to the inverter controlable frequency and/or magnitude of voltage, both of the induction mode and the synchronous mode are possible in double excitation motor, and the proposed double excitation motor can be driven as a synchronous motor by the extra three-phase input. At the synchronous mode the efficiency is improved so higher than that at induction mode or induction motor. The rating of the inverter used for speed control can be reduced upto one-fifth of that for conventional induction motor. Also the cost and maintenance fee of double excitation induction motor can be reduced compared to any other motors.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.60 no.12
• /
• pp.2225-2229
• /
• 2011

Squirrel cage induction motor is the main driving system of industrial field and familiar with its use in a large variety of applications. However, many engineer are unfamiliar with the induction generator, even though no difference exists between both machines except for the mode of operation. But an induction generator is commonly used for micro & small hydro power applications due to its simplicity, reliability, low cost and robustness. Input and output of induction motor has turned against at the induction generator operation. Rotation speed of induction generator is small faster than induction motor. As output of induction machines increases with the increasement of speed, so loss is same. Actually, generator efficiency is lower than motor at this condition. If induction generator is connected with mechanical load, total efficiency is decreased. In this paper, we analyzed that input, output, torque and efficiency is different from each other above and below synchronous speed.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.65 no.1
• /
• pp.1-6
• /
• 2016

Recently, proportion of the induction motor load is gradually increased. When a contingency in the power systems, it has been discovered phenomenon that the voltage is delayed recover caused mechanical characteristics of the induction motor load. It can be a serious impact on the voltage stability of the power system considering induction motor load. The scheme to mitigate this phenomenon tripping off the motors to prevent voltage drop and delayed voltage recovery on the load demand side. Fault induced delayed voltage recovery phenomenon is caused by stalling of small induction motor load in transmission level contingencies. In this paper, fault induced delayed voltage recovery phenomenon mitigation method implementation under voltage load shedding on the korean power system considering induction motor load.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1997.10a
• /
• pp.319-322
• /
• 1997

In vector control technique, stator currents of an induction motor are transformed to equivalent d-q currents in reference frame consist of d and q axis, each of which is coincide with flux and torque direction respectively. In this paper, the new algorithm is suggested where the stator current through an induction motor torque is monitored by using a vector control method where an additional equipment is not need. The G-programming is used to apply the suggested algorithm in the experiment and this is applied to an actual system to monitor the torque value of an induction motor on real time. To solve the vibration trouble of estimated torque caused from an unbalanced real rotating speed of an induction motor and measured rotating speed by suggesting the reconstructed in a method based on measurement current signal. This produced system testifies an accuracy of an induction motor through the experiment by comparing the reference value of the control method.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.59 no.10
• /
• pp.1882-1888
• /
• 2010

It is widely known that ESA(Electric Signature Analysis) method is very useful one for fault diagnosis of an induction motor. Online fault diagnosis system of induction motors using LabVIEW is proposed to detect the fault of broken rotor bars and shorted turns in stator. This system is not model-based system of induction motor but LabVIEW-based fault diagnosis system using FFT spectrum of stator current in faulty motor without estimating of motor parameters. FFT of stator current in faulty induction motor is measured and compared with various reference fault data in data base to diagnose the fault. This paper is focused on to predict and diagnose of the health state of induction motors in steady state. Also, it can be given to motor operator and maintenance team in order to enhance an availability and maintainability of induction motors. Experimental results are demonstrated that the proposed system is very useful to diagnose the fault and to implement the predictive maintenance of induction motors.

• Journal of Advanced Marine Engineering and Technology
• /
• v.23 no.1
• /
• pp.96-102
• /
• 1999

Sensorless speed estimation in induction motor systems is one of the most control engineers. Based on the estimated speed the vector control has been applied to the high precision torque control however most speed estimation methods use adaptive scheme so that it takes long time to estimate the speed. Thus the adaptive estimation scheme is not effective to the induction motor which requires short sampling time. In this paper a new linearized equation of induction motor system is proposed and a sensorless speed estimation algorithm based on observation techniques is developed. First the nonlinear induction motor equation is linearized at an equilibrium point. Second a proportional integral(PI) observer is applied to estimate the speed state in the induction motor system. Finally simulation results will assure the effectiveness of the new linearized equation and the sensorless estimation algorithm by using PI observer in the nonlinear induction motor system.

• Journal of Electrical Engineering and Technology
• /
• v.12 no.2
• /
• pp.761-768
• /
• 2017

This paper deals with the performance analysis of three phase induction motor considering its stator side faults and operating thermal limits. The speed control of induction motor using three phase boost converter operated by a MOSFET switch and a PI controller is demonstrated and presented in this article. IGBTs switches are used for inverter drive mechanism. The experimental result of speed control of induction motor using voltage control technique clearly shows better accuracy than conventional methods of speed control. A three phase 1HP 415V 0.78 kW 4 Pole induction motor is designed using motor solver software. Based on the parameters used in the software thermal analysis of induction motor is done and torque variation with conductor area, efficiency, output curve, losses in different parts of motor has been obtained. Also different types of faults namely under voltage, over voltage, stator imbalanced voltage, turn to turn, locked rotor bar, wrong alignment of rotor bar with respect to stator are studied and fault analysis is performed. Hence comparison is made based upon the results obtained before and after faults.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.11 no.3
• /
• pp.266-273
• /
• 2006

In difference with the rotary type electrical machinery, the single-sided linear induction motor(SLIM) that generates the direct thrust, is widely used for the operation system of electrified railroad, lope-less elevation system, conveyer system, and so on. The operational principle of single-sided linear induction motor is constructively similar to the general rotary Induction motor It Is difficult to realize the complicate linear induction motor which is applied space vector pulse width modulation(SVPWM) system, but widely used in vector motor control system or servo control system because of its high performance in current control. In this paper, we has modeled the dynamic characteristic analyzing methode, and calculated efficiently the end effect by using equivalent circuit methode in the operating linear Induction motor control system.

• Journal of Electrical Engineering and Technology
• /
• v.12 no.4
• /
• pp.1503-1510
• /
• 2017

In this paper, a thermal analysis of a high speed induction motor with a PWM voltage source was performed by considering harmonic loss components. The electromagnetic analysis of the high speed induction motor was conducted using the time-varying finite element method, and its thermal characteristics were carried out using the lump-circuit method. Harmonic losses from tests in the high frequency region were divided into core loss and conductor loss components using various ratios, in order to determine the loss distributions for the thermal analysis. The results from both the calculations and experiment were validated using a high speed induction motor prototype operating at 20,000rpm.

• Proceedings of the KIEE Conference
• /
• 2001.07b
• /
• pp.795-797
• /
• 2001

Voltage varing Fate dv/dt which is applied to induction motor usually makes unnegligible leakage current and it flows through stator winding and motor frame. This kind of harmonic leakage current makes effect on power source and cuases electromagnetic trouble because the motor frame has earth. Therefore in this study, a high frequency induction motor model is developed and analyze the motor performance to explain the phenomena. Inverter model is also developed and is combined with the motel model to prepare the basis of the high frequency effects on inverter fed induction motor.