• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.11a
• /
• pp.136-139
• /
• 2002

Previous valves have initial gap problem, high voltage or high pressure problem. In this paper, various micro valves with free floating structure have been fabricated and tested to solve the initial gap and high pressure problems. The paper presents how to etch Parylene-C which is a valve cap material without A1 mask layer. The maximum flow-rate of fabricated micro valve is$118{\mu\ell}$/min with $370{\mu}m$ orifice size and the leakage at the initial and reverse pressure is not observed.

• Structural Engineering and Mechanics
• /
• v.72 no.5
• /
• pp.597-615
• /
• 2019

The paper studies the dispersion of the axisymmetric longitudinal wave propagating in the "hollow cylinder + surrounding medium" system with inhomogeneous initial stresses caused by the uniformly distributed radial compressional forces acting at infinity. Up to now in the world literature, there exist only a few investigations related to the wave dispersion in a hollow cylinder with inhomogeneous initial stresses. Therefore, this paper is one of the first attempts in this field in the sense of the development of investigations for the case where the cylinder is surrounded with an infinite medium. The three-dimensional linearized theory of elastic waves is used for describing the considered wave propagation problem and, for a solution to the corresponding mathematical problem, the discrete-analytical solution method is developed and employed. The corresponding dispersion equation is obtained and this equation is solved numerically and, as a result of this solution, the dispersion curves are constructed for the first and second modes. By analyzing these curves, the character of the influence of the inhomogeneous initial stresses on the dispersion curves is established. In particular, it is established that as a result of the inhomogeneity of the initial stresses both new dispersion curves and the "band gap" for the wave frequencies can appear.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.16 no.2
• /
• pp.348-355
• /
• 1992

Casting structures and properties are determined by the solidification speed in the metal mold. The heat transfer characteristics of the interface between the mold and the casting is one of the major factors that control the solidification speed. According to Sully's research, the thermal resistance exists due to the air-gap formation at the mold-casting interface during the freezing process and the interface heat transfer coefficient is used to describe the degree of it. In this study, one-dimensional Stefan problem with air-gap resistance in the cylindrical geometry is considered and heat transfer characteristics is numerically examined. The temperature distribution and solidification speed are obtained by using the modified variable time step method. And the effects of the major parameters such as mold geometry, thermal conductivity, heat transfer coefficient and initial temperature of casting on the thermal characteristics are investigated.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.05a
• /
• pp.54-57
• /
• 2005

We have designed a single gap transflective liquid crystal display (LCD) driven by a fringe electric field, in which the +LC (${\Delta}{\varepsilon}$=7.4, rubbing angle= $80^{\circ}$) is homogeneously aligned in the initial state. This device is a problem that the voltage-dependent transmittance and reflectance curves do not match each other. Thus a dual driving circuit is required. This study shows that optimization of the rubbing angle in the transmissive and reflective regions solves this problem so that the transflective display with a single cell gap and single gamma curve for reflective and transmissive region is possible.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.16 no.6
• /
• pp.1205-1215
• /
• 1992

The solidification rate is of special importance in determining the casting structures and properties. The heat transfer characteristics at the interface between the mold and the casting is one of the major factors that control the solidification rate. The thermal resistance exists due to the air-gap formation at the mold/casting interface during the freezing process. In this study two-dimensional Stefan problem with air-gap resistance in the rectangular mold is considered and the heat transfer characteristics is numerically examined by using the enthalpy method. The effects of the major parameters, such as mold geometry, thermal conductivity, heat transfer coefficient, and initial temperature of casting, on the thermal characteristics are investigated.

• IE interfaces
• /
• v.22 no.3
• /
• pp.263-277
• /
• 2009

This research deals with a task assignment problem to worker group which consists of one master and one assistant. Each task must be assigned to only one worker group and it is possible to make a pair of each master and each assistant to organize a worker group. A worker group may have more than one task assigned to it, but the workloads of each worker group must be balanced within the allowable range. This problem can be formulated mathematically using the Mixed Integer Programming(MIP), where the objective function is to minimize the total assignment cost. A two phase heuristic algorithm is suggested in order to find approximate solutions. The first phase is to obtain an initial solution, where the initial assignment is performed to follow the workload adjustment. In the second phase, the solution is improved through the repeated process of the exchange and the assignment adjustment. Numerical experiments have been performed to evaluate the performance of the heuristic algorithm.

• Korean Journal of Health Education and Promotion
• /
• v.32 no.5
• /
• pp.43-51
• /
• 2015

Objectives: Socioeconomic factors are one of the significant factors explaining drinking problems in our society. From the poverty and inequality perspective, not only absolute poverty but perceived level of poverty or inequality has a direct effect on one's health and health behaviors. The purpose of the study is to explore the growth trajectories of problem drinking in Korea in relation to poverty and perceived income. Methods: Data from 13,414 adults were analyzed using 4 years of data (2010 to 2014) from the Korea Welfare Panel. Main variables included poverty status, perceived income inequality, and problem drinking. A latent growth modeling was employed for the analysis. Results: The non-poverty group had higher initial level of problem drinking; however, the poverty group showed higher rate of increase in problem drinking rate. The perceived income inequality had no significant influence on the initial level, but over time, those with higher level of perceived income inequality showed higher rate of increase in problem drinking. Conclusions: Findings showed that poverty and inequality affect changes in problem drinking. Efforts to prevent and decrease problems related to alcohol should not only focus on changing individuals' behavior but also on decreasing the inequality gap.

• Steel and Composite Structures
• /
• v.47 no.6
• /
• pp.795-811
• /
• 2023

When studying the resonance problem of nanoplates, the existing papers do not consider the influences of geometric nonlinearity and initial geometric imperfection, so this paper is to fill this gap. In this paper, based on the nonlocal strain gradient theory (NSGT), the nonlinear resonances of functionally graded (FG) nanoplates with initial geometric imperfection under different boundary conditions are established. In order to consider the small size effect of plates, nonlocal parameters and strain gradient parameters are introduced to expand the assumptions of the first-order shear deformation theory. Subsequently, the equations of motion are derived using the Euler-Lagrange principle and solved with the help of perturbation method. In addition, the effects of initial geometrical imperfection, functionally graded index, strain gradient parameter, nonlocal parameter and porosity on the nonlinear forced vibration behavior of nanoplates under different boundary conditions are discussed.

• Journal of KIISE:Information Networking
• /
• v.32 no.4
• /
• pp.495-507
• /
• 2005

Measuring the end-to-end available bandwidth in the Internet is a useful tool for distributedapplication services or QoS (Quality-of-Service) guarantee. To measure the end-to-end available bandwidth, Single-hop Gap model-based packet train measurement techniques are well-known. However, the error of packet train output gap can happen by network topologies. This error of the output gap causes the inaccuracy of the available bandwidth measurement. In this paper, we propose a new end-to-end available bandwidth measurement technique with accurate capacity measurement and fast convergence methods. To solve the erroneous capacity measurement problem of the back-to-back packet train transmission, we propose a new available bandwidth measurement method by decoupling the capacity measurement with the initial gap of the packet train. Also, we propose a new technique to predict the proper initial gap of the packet train for faster convergence. We evaluate our proposed method by the simulation in various topologies comparing with previous methods.

• Fibers and Polymers
• /
• v.2 no.4
• /
• pp.203-211
• /
• 2001

Residual stresses were predicted by a flow analysis in the mold cavity and residual stress distribution in the injection molded product was measured. Flow field was analyzed by the hybrid FEM/FDM method, using the Hele Shaw approximation. The Modified Cross model was used to determine the dependence of the viscosity on the temperature and the shear rate. The specific volume of the polymer melt which varies with the pressure and temperature fields was calculated by the Tait\`s state equation. Flow analysis results such as pressure, temperature, and the location of the liquid-solid interface were used as the input of the stress analysis. In order to calculate more accurate gap-wise temperature field, a coordinate transformation technique was used. The residual stress distribution in the gap-wise temperature field, a coordinate transformation technique was used. The residual stress distribution in the gap-wise direction was predicted in two cases, the free quenching, under the assumption that the shrinkage of the injection molded product occurs within the mold cavity and that the solid polymer is elastic. Effects of the initial flow rate, packing pressure, and mold temperature on the residual stress distribution was discussed. Experimental results were also obtained by the layer removal method for molded polypropylene.