• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.16 no.5
• /
• pp.105-112
• /
• 2017

In this study, plastics were deformed after molding due to the characteristics of the material. The Taguchi experimental design method was utilized to find the molding conditions that minimized deformation of the plastic bezel to be assembled in an automotive steering wheel. The injection molding conditions applied to the experimental design method are the melt temperature, cavity plate coolant temperature, core plate coolant temperature, and cooling time. Each condition was divided into five levels, and a total of 25 experiments were planned. However, instead of performing 25 actual molding experiments, the injection molding analysis was performed using the Moldflow program, and the deformation values for each molding analysis were obtained. The optimal molding conditions were obtained from these deformation values. The actual injection molding experiment using optimal molding conditions was compared with the deformation amount of the current molded product. The deformation was measured using a precise 3D scanner. The deformation amount of the molded product under optimal molding conditions was 16.1% lower than the deformation amount of the current molded product.

• Design & Manufacturing
• /
• v.13 no.2
• /
• pp.12-16
• /
• 2019

For optimal injection molding, various molding conditions should be combined well. Therefore, engineers should be thoroughly familiar with mold design, fabrication, and injection molding. The choice of resin among the various molding conditions is closely related to the productivity of the molded part and the deformation after molding, so the engineer must select the appropriate resin. Engineers work on the basis of data provided by resin manufacturers during molding. However, in actual molding work, it is necessary to apply values slightly different from those provided to obtain molded articles of desired performance. In this study, various deformations of molded products were compared with respect to crystalline resin and amorphous resin when molded according to the data provided by the resin maker and molded at the changed values at the work site.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.17 no.2
• /
• pp.67-74
• /
• 2009

Injection molding have been used for manufacturing various fields of automotive interior trims for years. The demands on the injection molding technique are grown with the further development of the automobile technique and the design presentations for cost reduction and environment-friendly. This paper shows that multi-component injection conditions are different from general injection, also shows how to optimize part design and mold design and how to manufacturing through the efficient use of multi-component injection in development process using core back system. To fulfill this purpose, all influential process parameters related to the quality of automobile parts were analyzed in terms of the correlation between them. Base on that, a innovative process will be developed by injection engineers to implement it in practice.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.06a
• /
• pp.1416-1419
• /
• 2005

Design and manufacturing of plastic injection mold with cavity pressure/temperature sensors were performed in the present study for tensile test specimen. Standards of mold-base and tensile test specimen were used to design an injection molding system. Cavity pressure and temperature sensors were placed on the side of fixed platen of injection mold machine to prevent them from external impact damage. Injection molding experiments with variations of injection speed and melt temperature were performed and polycarbonate tensile specimens were prepared for the tensile test. It was shown that injection molding processing parameters can have effect on the mechanical properties of the plastic injection molded part.

• Journal of the Korean Society for Precision Engineering
• /
• v.31 no.1
• /
• pp.9-13
• /
• 2014

The molding process can be divided into five separate steps: plastification, injection, holding, cooling, and finally ejection. In the plastic injection molding, the effect factor such as mold temperature, injection speed, packing pressure and inhomogeneous cooling under packing process affects both the article dimension and physical characteristics. Especially, the packing pressure is the most critical factor to affect molded articles quality among the packing parameters. In this paper, the CAE simulation considering the molding condition is performed to predict the faulty cause which appears in the packing process between cavities of injection molding machine. From the results of CAE simulation, the packing phenomena according to the product form and the gate position was investigated to improve the article quality and minimize the various molding defects. The effect of packing pressure and gate number on the injection molding was discussed.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.9 no.5
• /
• pp.1119-1124
• /
• 2008

This study presents the preform injection molding and the blow molding of the injection stretch-blow molding process for PET bottles. The numerical analysis of the injection molding and the blow molding of a preform is considered in this paper using CAE with a view to minimize the warpage and the thickness. In order to determine the design parameters and processing conditions in injection/blow molding, it is very important to establish the numerical model with physical phenomenon. In this study, a three dimensional model has been introduced for the purpose and flow simulations of filling, post-filling and cooling process are carried out. The simulations resulted in the warpage in good agreement with the measurements. Also, from the result of numerical analysis, we appropriately predicted the warpage, deformation and thickness distribution along the product walls.

• Elastomers and Composites
• /
• v.52 no.4
• /
• pp.309-316
• /
• 2017

In injection molding, the quality of an injection molded product varies greatly depending on the molding conditions. Many researche studies have been conducted on the quality analysis of molded parts according to the molding conditions such as injection pressure, injection temperature, and packing pressure. However, there have not been many studies on the V/P switchover timing. It is known that when a large pressure is applied to a cavity in the packing phase, the cavity pressure is most affected by the packing pressure. In addition, depending on the position (timing) of the packing pressure, it can have a direct influence on quality based on the shrinkage and dimensions of the molded parts. In this study, the change in pressure profile in the cavity according to the V/P switchover position is confirmed. A CAE analysis program (Moldflow) was used to simulate and analyze two models using the PC and PBT materials. In order to compare these results with the actual injection molding results, injection molding was performed for each V/P switchover position, and the correlation between simulation and experiment, especially for the shrinkage of molded parts, was evaluated.

• IE interfaces
• /
• v.18 no.1
• /
• pp.73-81
• /
• 2005

Injection molding has been widely used in producing plastic parts in large quantities. However, its productivity mainly depends on the expertise and experience of skilled workers because of the difficulty and complexity to determine a robust injection molding condition which is not influenced by the minor operational variation of an injection molding machine and produces good parts continuously. This study analyzes the defect types of the parts and proposes a support system to assist users in determining the robust process condition. The support system calculates the start condition from the information of an injection mold, the injection molding machine, the resin used, and the part. Through the iterative step which updates the condition using the defect information of the part tested, users can obtain the initial condition which produces the part without any problem for the first time. The support system also assists users in obtaining the robust condition from the initial condition using the technique of experimental design. To prove the validity of the support system, this study implements it in the control panel of the injection molding machine.

• Journal of Advanced Marine Engineering and Technology
• /
• v.34 no.2
• /
• pp.289-295
• /
• 2010

Injection molding process is one of the most important methods to produce plastic parts with high efficiency and low cost. Today, injection molded parts have been increased dramatically the demand for high strength and quality applications. In this study, In-line skates are made of Al alloy and plastic materials to replace the frame for the optimization process is all about. I interpreted through mold design, Injection molding process that minimizes the runner and the gate dimension will determine the size and shape. Runner and gate dimensions of change based on availability of the product, I'll discuss the injection molding. This report investigates that the optimum injection molding condition for minimum of shrinkage. The FEM Simulation CAE tool, Moldflow, is used for the analysis of injection molding process.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.14 no.11
• /
• pp.5352-5356
• /
• 2013

Plastic product manufacturing industry has usually focused on a mechanical and physical characteristics of molding. Recently, not only these characteristics but also the aesthetic value is significantly considering. Especially, the molding's gloss, which we can easily distinguish, is an important aesthetic point. In this study, it were investigated that the gloss variation of ABS moldings by changing injection conditions such as injection pressures, injection speed, holding pressures melt and mold temperatures by injection molding experiment. The experimental results revealed that the holding pressure was the most active condition on gloss of ABS molding.