• Journal of computational fluids engineering
• /
• v.21 no.1
• /
• pp.58-63
• /
• 2016

This research is to investigate the performance analysis for efficient design with four different inlet angles of the centrifugal pump impeller. Assuming that the rotation speed and exit angle are fixed, Four cases of the centrifugal pumps were numerically analyzed using ANSYS FLUENT. According to the numerical results, head and pump efficiency at inlet angle of 20 degrees was highest. There is no big difference of efficiency at inlet angle of 20 degrees compared to the inlet angle 30 degrees. About 15% of efficiency at inlet angle of 20 degrees is higher than inlet angle of 40 degrees and 31% higher than inlet angle oof 50 degrees. Because there is liner functional relationship between speed and flow rate, suction flow rate at inlet angle of 20 degrees is superior to the inlet angle of 30 degrees as much as 0.89%, inlet angle of 40 degrees as 13%, inlet angle of 50 as 28.4%. Head at inlet angle of 20 degrees is superior to the inlet angle of 30 degrees as much as 0.4%, inlet angle of 40 degrees as 2.7%, inlet angle of 50 degrees as 3.2%. There should exist highest efficiency and also optimal design shape at inlet angle of 20 degrees.

• Proceedings of the KSME Conference
• /
• 2004.04a
• /
• pp.1969-1974
• /
• 2004

The performance of small cyclone is analysed by an experiment for the purpose of developing a bag-less vacuum cleaner. For the high collection efficiency and low pressure loss cyclone, the effect of cyclone inlet feature must be well understood. Four types of the helical inlet are considered to compare with the normal tangential inlet, and also various inlet velocities are used to each inlet type. Based on the reference dimension, each type of inlet shows the changes of the grade efficiency and pressure loss which determine the cyclone quality. The results show that the helical inlet has the smaller cut-size but bigger pressure loss than the tangential inlet. And the degree of opening area influences factors of cyclone performance. As the inlet velocity is increased, the cut-size becomes smaller and the pressure loss becomes bigger of each cyclone. Further studies are required to understand the optimized helical inlet of cyclone.

• International Journal of Aeronautical and Space Sciences
• /
• v.8 no.2
• /
• pp.121-125
• /
• 2007

In late 1960's, engineers of the engine manufacturer experienced that the distortion of inlet flow of turbofan and turbojet engine could cause the surge in compressor and affect overall engine operational performance, which result in the deterioration of stability of the engine. In this study, block type of inlet distortion simulating device has been developed in order to investigate the effect of inlet distortion on the deterioration of overall engine operational performance. The inlet distortion simulating device was installed in front of engine inlet in order to simulate distortion of inlet flow. The degree of inlet distortion was measured by rakes installed upstream the inlet distortion simulating device and between the engine inlet and inlet distortion simulating device. Before applying the inlet distortion simulating device to real engine, preliminary tests were performed with a simulated engine in order to verify the degree of inlet distortion by the device. Preliminary inlet distortion tests were performed in Altitude Engine Test Facility(AETF) of Korea Aerospace Research Institute(KARI) and results showed that the inlet distortion simulating device could be used in simulating various inlet distortion cases.

• International Journal of Aeronautical and Space Sciences
• /
• v.6 no.1
• /
• pp.1-7
• /
• 2005

The inlet boundary condition of computations about the supersonic turbine flow is commonly applied as far-field inlet boundary condition with specified velocity. However, the inflow condition of supersonic turbine is sometimes affected by the shocks or expansion waves propagated from leading edges of blade. These shocks and expansion waves alter the inlet boundary condition. In this case, the inlet boundary condition can not be specified Therefore, in this paper, numerical analyses for three different inlet conditions - fa-field inlet boundary condition, inlet boundary condition with a linear nozzle and inlet boundary condition with a converging-diverging nozzle - have been performed and compared with experimental results to solve the problem. It is found that the inlet condition with a linear nozzle or a converging-diverging nozzle can prevent changing of inlet boundary condition, and thus predict more accurately the supersonic flow within turbine cascade than a far-field inlet boundary condition does.

• 한국전산유체공학회:학술대회논문집
• /
• 2008.03a
• /
• pp.262-267
• /
• 2008

Numerical investigations were performed with an external-compression inlet with a three-dimensional bump at Mach 2 to scrutinize the geometrical effects of the bump in controlling the interaction of a shock wave with a boundary layer. The inlet was designed for two oblique shock waves and a terminal normal shock wave followed by a subsonic diffuser, with a circular cross-section throughout. The bump-type inlet that replaced the aft ramp of the conventional ramp-type inlet was optimized with respect to the inlet performance parameters as well as compared with the conventional ramp-type inlet. The current numerical simulations showed that a bump-type inlet can provide an improvement in the total pressure recovery downstream of the shock wave/boundary layer interaction over a conventional ramp-type inlet.

• 한국전산유체공학회:학술대회논문집
• /
• 2008.10a
• /
• pp.262-267
• /
• 2008

Numerical investigations were performed with an external-compression inlet with a three-dimensional bump at Mach 2 to scrutinize the geometrical effects of the bump in controlling the interaction of a shock wave with a boundary layer. The inlet was designed for two oblique shock waves and a terminal normal shock wave followed by a subsonic diffuser, with a circular cross-section throughout. The bump-type inlet that replaced the aft ramp of the conventional ramp-type inlet was optimized with respect to the inlet performance parameters as well as compared with the conventional ramp-type inlet. The current numerical simulations showed that a bump-type inlet can provide an improvement in the total pressure recovery downstream of the shock wave/boundary layer interaction over a conventional ramp-type inlet.

• Advances in aircraft and spacecraft science
• /
• v.5 no.4
• /
• pp.431-444
• /
• 2018

Numerical simulations have been conducted to study the unstart/restart characteristics of an over-under turbine-based combined-cycle propulsion system (TBCC) inlet during the inlet transition phase. A dual-solution area exists according to the Kantrowitz theory, in which the inlet states may be different even with the same input parameters. The entire transition process was divided into five stages and the unstart/restart hysteresis loop for each stage was also obtained. These loops construct a hysteresis surface which separates the operating space of the engine into three parts: in which a) inlet can maintain a started state; b) inlet keeps an unstarted state; c) inlet state depends on its initial state. During the transition, the operation of the engine follows a certain order with different backpressures and splitter angles, namely control route, which may result in disparate inlet states. Nine control routes with different backpressures and transition stages were designed to illuminate the route-dependent behavior of the inlet. The control routes operating towards the unstart boundary can make the inlet transit from a started state into an unstarted one. But operating backward the same route cannot make the inlet restart, additional effort should be made.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2004.03a
• /
• pp.634-643
• /
• 2004

In this paper are presented a concept of a new supersonic air inlet, which is designated a Multi-Row Disk (MRD) inlet, aiming at performance improvement under off-design conditions, and results of wind tunnel tests examined performance characteristics of the MRD inlet. The MRD inlet is frequently called ‘a skeleton inlet’ because of its appearance. The performance of a conventional axisymmetric inlet with a solid center body (spike) deteriorates under off-design Mach number conditions. It is due to the fact that total pressure recovery (TPR) governed by the throat area of inlet and mass capture ratio (MCR) governed by an incidence position of an oblique shock from the spike tip into the cowl can not be controlled independently in such air inlet. The MRD inlet has the spike that is composed of a tip cone and several disks arranged downstream of it, based on the experimental fact that several deep cavities on a conical surface have little negative effect on the boundary layer growth. The overall spike length of the MRD inlet is adjustable to the given flight speed by changing space between disks so that a spillage flow can be controlled independently from controlling the throat area. It could be made clear from the result of wind tunnel tests that the MRD inlet improves TPR by 10% compared with a conventional inlet with a solid spike under off-design conditions.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.18 no.3
• /
• pp.701-706
• /
• 1994

The discharge coefficients of critical sonic nozzles were obtained in a high pressure gas flow standard system, which was a gravitational weighing system. The discharge coefficients of critical sonic nozzle farbricated according to ISO specifications are in good agreement with ISO correlation. The discharge coefficients for small inlet radius decrease significantly as the inlet length become short due3 to separation at the sharp-edged inlet. For nozzles having long inlet radius, the effects of inlet length on the discharge coefficients were relatively small, but the effects become significant at the short inlet length. The effect of separation at the sharp-edged inlet is stronger than that of the boundary layer growth. The experimental results support that the shape of critical sonic nozzles suggested by ISO specifications is excellent.

• Proceedings of the KSME Conference
• /
• 2000.04b
• /
• pp.746-752
• /
• 2000

A study on discharge characteristics of a rotating discharge hole is very important to enhance the performance of an induction motor which have external forced cooling system. The discharge characteristics of rotating discharge holes are influenced by rotating speed, length-to-diameter ratio, inlet shape of rotor holes, etc. An experimental study on the effect of chamfered inlet edge of rotor inlet part with various depth-to-diameter and inlet chamfered edge angle is conducted. Depth-to-diameter ratios range from 0 to 0.5 and inlet chamfered edge angle range from 0 to 60. As a result, there is an optimal design point of inlet chamfered edge depth. And the inlet edge angle far maximum discharge coefficient is influenced mainly by the rotating speed of discharge holes.