• Journal of Biosystems Engineering
• /
• v.31 no.6 s.119
• /
• pp.474-481
• /
• 2006

In this paper, a new type blow head was developed and pneumatic application system was evaluated. The blow head had one operating factor, inserting length of collecting plate, that was directly related to discharge rate and application pattern. To determine Proper blow head arrangement and application height, a blow head set was tested. Three-way ANOVA was conducted to investigate relationships between CV value, the discharge rate and inserting length of collecting plate. The discharge rate and inserting length of collecting plate were statistically significant at p=0.01, affecting uniformity of application pattern. The best CV value among the application tests was 23.3% when the application rate and application height was 23.5 g/sec and 80 cm respectively. The worst CV value was 63.3% in 111.4 g/sec. Therefore, it is necessary to increase number of blow head in a section of the boom in improve application uniformity.

• Journal of Korean Society of Steel Construction
• /
• v.18 no.2
• /
• pp.251-259
• /
• 2006

In some cases, wooden structures are used for medium-rise buildings. It is therefore necessary to develop and test a new structural system for medium-rise buildings using wooden structures. This study deals with high-performance, laminated, timber-based composite members, which consist of structural laminated timber and H-beam. Simple beam tests were performed to determine the strength, stress distributions, and failure patterns of laminated timber. The main parameters are the insertinglength (1, 1.5, and 2 times the H-beam height) and the epoxy between the top/bottom flange of the H-beam and the top/bottom flange of the laminated timber. The results of the test show that the specimen with an inserting length that is 2 times the H-beam height was characterized by fairly god strength and stiffness.

• Sleep Medicine and Psychophysiology
• /
• v.8 no.2
• /
• pp.129-137
• /
• 2001

Objectives: The purpose of this study is to investigate the effects of 38-hour sleep deprivation on fine motor performance. The Motor Performance Series (MPS) in the Vienna Test System (computerized neurocognitive function tests) was used in this study. Methods: Twenty four subjects participated in this study. Subjects had no past history of psychiatric disorders and physical illness. Subjects had normal sleep-waking cycle without current sleep disturbances and were all right-handed (Annett's Hand Preference Questionnaire: above +9 points). To minimize the learning effects, familiarization with the Vienna Test System was performed one day before the study. Subjects were to get up at 6:00 in the morning after getting enough sleep according to his or her usual sleep-wake cycle. After awakening, subjects remained awake for 38 hours under continuous surveillance. During two consecutive study days, the subjects tested MPS at 7 AM and 7 PM each day, which means the MPS was done four times in total. During the experiment, anything that could affect the subjects' sleep such as coffee, tea, alcohol, a nap, tiring sports, and all medications were prohibited. Results: In MPS, the fine motor functions of both hands decreased after 38 hours of sleep deprivation. The decrement in motor performance was prominent in the dominant right hand. In the right hand, the total number of tapping was reduced (p<.005), and the number of misses (p<.05) and the length of misses (p<.05) of line tracking, the total length of inserting a short pin (p<.01), the total length of inserting a long pin (p<.05), and the number of misses in aiming (p<.05) increased. Such performance decrement was distinct in the morning sessions. Conclusions: These results suggest that fine motor performance decrement during sleep deprivation is predominant in the right hand, which exerts maximal motor function. The finding of decrement in motor function in tapping during sleep deprivation also suggested that the time required for exhaustion of muscles is shortened during sleep deprivation. More deterioration of motor performance was shown in the morning, which could be explained as circadian rhythm effects.

• KIEAE Journal
• /
• v.8 no.3
• /
• pp.77-83
• /
• 2008

The effective mixture of structural laminated timber and other materials is expected to extend the potentials of building structures because of the potentials to realize high performance in structural safety. The classical joint types using drift pin and bolts are occurred local failures due to the small bearing area. In result, new joints using H shaped steel were suggested in this research. The objective of this study is to evaluate elasto-plastic behaviors by strengthening types of wood frames with new joints connecting structural laminated timber with H shaped steel. A total of five specimens of about one-second scale were tested. Specimens had columns with 1,050 height and $84mm{\times}100mm$ section, and a beams with 1,950mm length and $130mm{\times}100mm$ section. Also, the specimens were stiffened by brace, hwang-toh brick, and autoclaved lightweight concrete. The results of the test showed that the specimen stiffened with autoclaved lightweight concrete was characterized by fairly good strength and stiffness than those of the other specimens. Initial stiffness of H-2.0D-NS specimen with 2 times inserting length of beam height showed 1.33 times than that of H-1.5D-NS specimen. However, the strength of H-2.0D-NS specimen has not improved too much than H-1.5D-NS specimen.

• Journal of Biosystems Engineering
• /
• v.31 no.6 s.119
• /
• pp.482-488
• /
• 2006

Application of precision farming technology to rice cultivation could be an effective measure for rice quality improvement and environment-friendly agriculture. This study was conducted to develope a variable rate pneumatic granule applicator. Previous study reported that application uniformity of the prototype machine (C.V. = 23.3%) was not satisfactory. To improve the uniformity, increase of blow-head number from 12 to 16 was suggested. Analysis of the pneumatic conveying system showed that increase of number of blow-head was possible. Three-way variance analysis of the modified applicator showed that inserting length should be changed according to granule metering rate. The range of metering rate from 27.3 to 417.9 g/s were divided into 4 levels and 4 sets of inserting lengths were determined to ensure CV values less than 15%. The revised applicator showed satisfactory C.V. values of 9.4 to 14.6% in the metering rate. Granule conveying pattern was observed using a high speed camera and judged as the homogeneous flow pattern.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.59 no.5
• /
• pp.847-853
• /
• 2010

This paper describes switching surge analysis for reclosing decision in 345kV combined transmission line with XLPE power cable. Reclosing operation should be decided based on the detailed technical analysis in combined transmission line because this line includes power cable section which is week on insulation. Insulation of power cable can be breakdown at the week point in case of reclosing moment. Therefore the detailed analysis has to be carried out by considering several conditions such as length ratio of power cable section, arrestor, inserting resistance, charging rate, grounding resistance, etc.. On the other hand sheath voltage on IJ(Insulated Joint) is analyzed to check dangerous condition on cable cover. Analysis is performed by EMTP/ATP. Analysis results show that reclosing can be operated as the single line-to-ground fault occurs on overhead line in 345kV combined transmission line, if the inserting resistance is considered before the operation of main circuit breaker.

• International Journal of Advanced Culture Technology
• /
• v.3 no.1
• /
• pp.145-152
• /
• 2015

The article aims to apply a friction stir spot welding for producing the lap joint between AA5052 aluminum alloy and C11000 copper alloy. The dimension of the materials was 100 mm in length, 30 mm in width and 1.0 mm in thickness. The copper plate was set overlap the aluminum plate by 30 mm. The welding parameter was the rotating speed of 2500-4000 rpm, the pin inserting rate of 2-8 mm/min and the holding time of 6 sec. The mechanical properties test and the microstructure investigation were performed to evaluate the lap joint quality. The summarized results are as follows. The friction stir spot welding could produce effectively the lap joint between AA5052 and C11000 copper. Increase of the rotating speed and holding time directly affected to decrease the tensile shear strength of the lap joint. The optimized welding parameters in this study that indicated the tensile shear strength of 864 N was the rotating speed of 3500 rpm, the pin inserting rate of 6 mm/min and the holding time of 4sec. The experimental results also showed that the hardness of the weld metal was lower than that of the base materials.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.7 no.6
• /
• pp.1229-1235
• /
• 2003

When finite length image signal is decomposed into 2-band signal and synthesized using 2-band orthogonal wavelet transform, boundary signals are not reconstructed perfectly. To reconstruct them perfectly, the filters which are different from wavelet filter are applied to the boundary signals. Since the existing boundary filters show poor frequency characteristic, the improvement of performance is bounded in practical applications. In this paper, the design method of improvement of frequency characteristic is proposed using inserting a zero to boundary filters which can reconstruct the boundary regions perfectly. Even though the length of proposed boundary filters is shorter, they show 4.2dB∼6.59dB gains in pass band and stop band error power compared with existing boundary filters. But synthesis process is some complicated.

• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.33 no.3
• /
• pp.114-122
• /
• 2010

The Probabilistic Traveling Salesman Problem (PTSP) is an important topic in the study of traveling salesman problem and stochastic routing problem. The goal of PTSP is to find a priori tour visiting all customers with a minimum expected length, which simply skips customers not requiring a visit in the tour. There are many existing researches for the homogeneous version of the problem, where all customers have an identical visiting probability. Otherwise, the researches for the heterogeneous version of the problem are insufficient and most of them have focused on search base algorithms. In this paper, we propose a simple construction algorithm to solve the heterogeneous PTSP. The Minimum Expected Length Insertion (MELI) algorithm is a construction algorithm and consists of processes to decide a sequence of visiting customers by inserting the one, with the minimum expected length between two customers already in the sequence. Compared with optimal solutions, the MELI algorithm generates better solutions when the average probability is low and the customers have different visiting probabilities. We also suggest a local search method which improves the initial solution generated by the MELI algorithm.

• Korean Journal of Optics and Photonics
• /
• v.2 no.4
• /
• pp.197-202
• /
• 1991

The real time autocorrelator has been developed in order to measure the pulse widths of ultrashort laser pulses using the SHG method. The scanning range of the autocorrelator is 142 ps, and inserting a delay block in one arm of the autocorrelator, the scanning range can be extended to 250 ps. The shortest pulse width was measured to be 20 ps, when the cavity length was well matched to the RF frequency of the mode-locker, and broadened to be 39 ps and 47 ps as the cavity length was detuned.