• Journal of Periodontal and Implant Science
• /
• 제28권4호
• /
• pp.809-822
• /
• 1998

Adequate root preparation in the treatment of periodontal disease often involves mechanical instrumentation to remove plaque, calculus perhaps contaminated cementum. Although meticulous scaling and root planing may remove some cementum, the use of aggressive root planing to remove cementum does not appear warranted. So ultrasonic device and rotary instrument appear to be replacing hand instrument. But it is not clear those instruments make smooth root surface as hand instrument. The roghness of the root surface were evaluate with SEM following instrumentation with Gracey curette, Perio Clean and piezo ultrasonic device(Setlec) with various tip. 20 extracted teeth were used in vitro experiment, and 9 teeth of a patient destined for extraction for periodontal reasons were utilized in vivo experiment. It was demonstrated that hand curette created the smoothest surface, while diamond tip tended to roughen the root surface. But the hand curette, Perio Clean, and piezo ultasonic device with scaler tip tend to remove cementum completely. Piezo ultrasonic device with curette-like tip made the desirable smooth surface with partial removal of cementum.

• 한국항행학회논문지
• /
• 제15권1호
• /
• pp.25-31
• /
• 2011

최근에는 NMEA 2000 프로토콜이 SOLAS 선박의 실시간 네트워크 장비의 표준으로 인증 된다. 본 논문에서는 항해 필수 장비인 초음파 센서를 이용한 NMEA 2000이 탑재된 2차원 풍향 풍속계를 개발하였다. 개발된 시스템은 NMEA 2000 장비와의 연결을 테스트하기 위해 수심, 속도, GPS 장비로 구성된 NMEA 2000 네트워크에 연결하였으며, 기존에 제작된 타사 풍향 풍속계와 비교하기 위해 기능시험을 수행하였다.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2005년도 ICCAS
• /
• pp.1127-1131
• /
• 2005

One of problems in industries is an installation for an automation system device such sensor, transducer, controller, and so on those are located in different areas. Such problem makes a difficulty for maintenance and installation. The aim of this research attempts to design a high performance controller with remote devices. One attractive is to group near devices in near place together to centralizes control. This paper presents network device groups distributed through digital and analog Remote Terminal Unit (RTUs). Such devices are centralized by computer or PLC control and communicated with similar protocol through serial bus. Our scheme, there are many advantages such as, saving both time and cost,convenience compared to other ways.

• Journal of Korean Neurosurgical Society
• /
• 제41권2호
• /
• pp.77-81
• /
• 2007

Objective : In a variety of thoracolumbar diseases, corpectomy followed by interbody bone graft and anterior instrumentation has allowed direct neural decompression and reconstruction of the weight-bearing column by short segments fusion. In this study, we compared spinal stability of the two different anterior thoracolumbar instruments : Z-plate and Kaneda device representing plate and two-rods type, respectively. Methods : A retrospective review was performed for all the patients with thoracolumbar diseases or traumas treated with anterior corpectomy, autologous iliac bone graft, and fixation with instruments from 1996 to 2000. For the anterior instrumentation, Z-plate or Kaneda device was used for 24 [M:F=5:9, average age=37] and 12 [M:F=9:3, average age=41] patients, respectively. The plain AP and lateral flexion-extension films were taken immediately after surgery and at each follow-up. The sagittal and coronal Cobb's angles at the operation segments were used to observe the change of initial fixation status. The surgical time length and bleeding amount of the two groups were compared. Intra-operative and post-operative instrument associated complications were evaluated. Student t-test was used for statistical analysis and p-value less than 0.05 was considered to be significant. Results : Mean follow-up durations for Z-plate and Kaneda device were 24 and 21 months, respectively. The fusion rate was 91% for Z-plate and 100% for Kaneda device. Two cases of Z-plate group showed instrumentation failure during the follow up period, in which additional surgery was necessary. The mean differences of sagittal Cobb's angles among the AP images immediate after surgery and at follow-up were 7 and 2 degrees for Z-plate and Kaneda device, respectively [p<0.05]. The mean differences of coronal Cobb's angles were 5 and 2 degrees for Z-plate and Kaneda device, respectively [p<0.05]. No Intra-operative complication has occurred in both groups. There was no difference in surgery time and bleeding amount between two groups. Conclusion : We think that Kaneda device [rod type] is stronger than Z-plate [plate type] to keep the spinal stability after anterior thoracolumbar surgery.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2005년도 ICCAS
• /
• pp.2397-2401
• /
• 2005

It is well understood that force reflecting coupled with visual display can be an important two-way communication channel in human-computer interaction. In this work, important components for a high-fidelity system bandwidth are force reflecting device and that all the computations including contact determination and response computation have to be performed in less than a millisecond. This paper describes a force-reflecting device and an embedded controller. The realized force-reflecting device is based on a novel serial type mechanical structure, and features compactness, high sustained output force capability, low friction, zero backlash, and enough workspace. The embedded controller reduces software computational load via main processor and simplifies hardware strictures by the time-division control. The device is integrated with existing dynamic simulation algorithms running separate workstation, so that objects can be manipulated in real time and the corresponding forces felt back by the operator.

• 한국기계가공학회지
• /
• 제21권4호
• /
• pp.31-38
• /
• 2022

In this study, we designed and manufactured an intelligent gripper-control device to safely grip unknown objects. The gripper control device consists of a DSP circuit, power supply circuit, communication circuit, and amplifier circuit diagrams. The DSP is used because the values of the 3-axis force sensor to which the gripper is attached are measured and calculated at high speeds. The gripping force is determined based on this value, and the object must be safely gripped with the determined value. A basic characteristic test of the control device of the manufactured intelligent gripper was conducted, and it was confirmed that it operated safely.

• 한국정밀공학회지
• /
• 제21권8호
• /
• pp.157-163
• /
• 2004

Scoliosis is a complex musculoskeletal dieses requiring 3-D treatment with surgical instrumentation. To investigate the effects of correction surgery, a finite element model of personalized model of the scoliotic spine that will allow the design of clinical test providing optimal estimation of the post-operation results was developed. Three dimensional skeletal parts, such as vertebrae, clavicle and scapular were modeled as rigid bodies with keeping their morphologies. Kinematical joints and spring elements were adapted to represent the inter-vertebral disc and ligaments respectively. With this model, two types of surgery procedure, distraction procedure with Harrington device and rod derotation procedure with pedicle screw and rod system had been carried out. The obtained simulation results were comparatively corresponding to the post operational outcomes and successfully demonstrated qualitative analysis of surgical effectiveness. From this analysis, it has been found that the preparing of appropriate rod curvature and its insertion was more important than just performing the excessive derotation for scoliosis correction.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2001년도 전력전자학술대회 논문집
• /
• pp.183-188
• /
• 2001

In this paper, we have developed a new Force-Display system using tendon-driven method based multiple DC motors. The proposed system is based on the HIR Lab Haptic library, which calculates the real position and renders the reflecting force data to device rapidly. The system is composed of device based tendon- driving method, high-speed controller and Haptic rendering library. The developed system will be used on constructing the dynamical virtual environment. To show the efficiency of our system, we designed simulation program, which an display the moving force (attaching, grabbing, rotating) on two virtual points. As the result of the experiment, our proposed system shows much higher resolution than any others.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1994년도 추계학술대회 논문집 학회본부
• /
• pp.353-355
• /
• 1994

This work describes a hardware implementation of a precision image tracking system which employs a CCD camera mounted on pan/tilt device. Unknown translation between two successive images of a moving object is estimated by using a generalized least-squares method. Estimated position error obtained by the tracking algorithm is used to drive DC motors built in the pan/tilt device for the camera to follow the image. An experimental result shows a sub-resolution tracking error for a image moving with a uniform velocity.

• 제어로봇시스템학회논문지
• /
• 제21권8호
• /
• pp.794-800
• /
• 2015

This paper describes the design for a defective product inspection device for the curved glass used in smart-phone. Cameras are used as inspection devices to find cracks in LCDs (Liquid Crystal Displays), PDPs (Plasma Display Panels), etc. The devices used to inspect the curved glass used in smart-phone consist of a camera, two back-light apparatus, an inspection apparatus main body, and an image processing program. Camera image calibration was performed to smooth an image taken with the camera, and as a result, the average error was less than 0.12 pixels. And the image of a smart-phone's curved glass taken with the camera was processed using the produced program. As a result, the program could correctly extract the cracks on the curved glass. Thus, it is thought that the designed inspection device can successful detect cracks in curved tempered glass.