• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.20 no.3
• /
• pp.457-463
• /
• 2016

In this paper, a method of enhancing the bandwidth of a double-dipole quasi-Yagi antenna (DDQYA) using a modified integrated balun is presented. The modified integrated balun consists of a microstrip (MS) line inserted along the center of a coplanar strip (CPS) line and the end of the MS line is connected to the CPS line through a shorting pin at the feed point. The geometry of the modified integrated balun is adjusted to improve the bandwidth of the DDQYA. In addition, the performance of the proposed balun in a back-to-back configuration is compared with a conventional balun. The proposed antenna with the optimized modified integrated balun is fabricated on an FR4 substrate, and the experiment results show that the antenna has a frequency band of 1.56-3.04 GHz(64.4%) for a VSWR < 2, which shows enhanced bandwidth compared to the DDQYA with the conventional balun.

• 한국정보통신설비학회:학술대회논문집
• /
• 2007.08a
• /
• pp.423-426
• /
• 2007

An active Balun is designed for RFID reader at 2.45GHz. The Balun is integrated inside the receiver, then the LNA and mixer can be connected. The unbalanced LNA output signal is transformed to a balanced signal at the input mixer The RF mixer and LO mixer, by using this balun. The Balun provided a balanced signal with two output stage, gain mismatch is 0.116dB. The phase show a good behavior with $163.918^{\circ}$,$-16.609^{\circ}$. The phase mismatch is about $0.527^{\circ}$. The tight difference between the gain and phase on each brancd, is because of the used capacitor and integrated inductor and the other parasitic element inside the balun.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.39 no.12
• /
• pp.553-558
• /
• 2002

In this paper, an integrated balun using bondwire transformer is fabricated and measured. The bondwire transformer has 1ow conductor and substrate loss and kas high resonance frequency. So it is available to implement low loss broadband balun. From the measured results, 0.7 dB amplitude imbalance and about 2.5 $^{\circ}$ phase imbalance was achieved from 8.15 to 16.18 GHz. It is expected that the proposed balun can improve the performance of mixers, amplifiers and matching networks of antennas. It can also be integrated with other components due to its easier fabrication and smaller size than spiral transformer balun.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.8 no.2
• /
• pp.143-149
• /
• 2008

A novel compact model for a five-port transformer balun is proposed for the efficient circuit design of hybrid balun. Compared to the conventional model, the proposed model provides much faster computation time and more reasonable values for the extracted parameters. The hybrid balun, realized in $0.18\;{\mu}m$ CMOS, achieves 2.8 dB higher gain and 1.9 dB lower noise figure than its passive counterpart only at a current consumption of 0.67 mA from 1.2 V supply. By employing the hybrid balun, a differential zero-IF receiver is designed in $0.18\;{\mu}m$ CMOS for IEEE 802.15.4 ZigBee applications. It is composed of a differential cascode LNA, passive mixers, and active RC filters. Comparative investigations on the three receiver designs, each employing the hybrid balun, a simple transformer balun, and an ideal balun, clearly demonstrate the advantages of the hybrid balun in fully differential CMOS RF receivers. The simulated results of the receiver with the hybrid balun show 33 dB of conversion gain, 4.2 dB of noise figure with 20 kHz of 1/f noise corner frequency, and -17.5 dBm of IIP3 at a current consumption of 5 mA from 1.8 V supply.

• Journal of Satellite, Information and Communications
• /
• v.12 no.1
• /
• pp.132-136
• /
• 2017

In this paper, expanded lowest operating frequency by adopting circular slot on ground of balun and balance improved balance performances by stacking dielectric layer balun is proposed. Bandwidth of proposed balun is 1~7 GHz, and electrical length is $0.05{\lambda}$ at 1 GHz. In order to check performances of the proposed balun, simple dipole is integrated with the balun and radiation pattern of dipole is measured.

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2003.11a
• /
• pp.630-637
• /
• 2003

In this paper, a DBM(double balanced mixer) of 2 GHz is implemented on FR4(h=1.6mm, ${\epsilon}_r=4.6$) substrate. The structure of double balanced mixer requires, in general, two talons and a quad diode. For balun, a novel planar balun using microstrip to CPS(Coplanar Strip) is suggested and designed. The suggested balun shows the phase imbalance of $180^{\circ}{\pm}1.5^{\circ}$ and the amplitude imbalance of ${\pm}0.2 dB$ for 1.5 to 2.5 GHz. Using the balun, DBM is successfully implemented, and the measured conversion loss of up/down converter show about 6 dB over the bandwidth. The balun may be applicable for MMIC(Monolithic Microwave Integrated Circuit) DBM with the process supporting backside via though more study.

• Proceedings of the IEEK Conference
• /
• 2005.11a
• /
• pp.261-264
• /
• 2005

This paper presents the design of a down-conversion mixer with built-in active balun integrated in a $0.25\;{\mu}m$ pHEMT process. The active balun consists of series-connected common-gate FET and common-source FET. The designed balun achieved broadband characteristics by optimizing gate-width and bias condition for the reduction in parasitic effect. From DC to more than 6GHz, the active balun shows the phase error of less than 3 degree and the gain error of less than 0.4 dB. A single-balanced down-conversion mixer with built-in broadband active balun has been designed with optimum width, load resistor and bias for conversion gain and without any matching component for broadband operating. The designed mixer whose size of including on-chip bias circuit is $1\;mm{\times}1\;mm$ shows the conversion gain of better than 7 dB from 2 GHz to 6 GHz and $P_{1dB}$ of -10 dBm at 5.8 GHz

• Journal of Advanced Marine Engineering and Technology
• /
• v.37 no.1
• /
• pp.99-104
• /
• 2013

In this paper, we developed a fully integrated downconverter MMIC (monolithic microwave integrated circuit) including Lange coupler and output active balun for millimeter wave applications. Concretely, ${\lambda}$/4 transmission line was added to Lange coupler for size reduction of RF/LO input, and mixed RF/LO signals were applied to gate of the FET of mixer. Active balun was used at output port for a coupling of out-of-phase IF output signals. According to measured results, the proposed downconverter MMIC showed good RF performances. For example, the downconverter MMIC showed an LO leakage power of -25 dBc at IF output port, and a RF-LO isolation of 18 dB. Therefore, off-chip components such as LO rejection filters were not required for a normal operation of the proposed downconverter MMIC. The proposed downconverter MMIC showed a conversion gain of 10.3 dB at RF frequency of 63 GHz. The size of the downconverter MMIC including all active and passive components was $2.2{\times}1.4mm^2$.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.15 no.1
• /
• pp.44-50
• /
• 2004

In this paper, a DBM(Doubly Balanced Mixer) of 2 GHz is implemented on FR4 substrate. The structure of doubly balanced mixer requires, in general, two batons and a quad diode. For balun, a novel planar balun using microstrip to CPS is suggested and designed. The suggested balun shows the phase imbalance of 180$^{\circ}$${\pm}$ 1.5$^{\circ}$and the amplitude imbalance of ${\pm}$ 0.2 ㏈ for 1.5 to 2.5 GHz. Using the balun, DBM is succesfully implemented, and the measured conversion loss of up/down converter show about 6 ㏈ over the bandwidth. The balun may be applicable for MMIC DBM with the process supporting backside via thourgh more study.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.15 no.5
• /
• pp.509-516
• /
• 2004

High-performance Si integrated passive process was developed using thick oxidation process and Cu-BCB process. This passive process leads to low-cost and high-quality RF module with a small form factor. The fabricated spiral inductor with 225 um inner diameter and 2.5 turns showed the inductance of 2.7 nH and the quality factor more than 30 in the frequency region of 1 ㎓ and above. Also WLCSP-type integrated passive devices were fabricated using the high-performance spiral inductors. The fabricated low pass filter had a parallel-resonance circuit inside the spiral inductor to suppress 2nd harmonics and showed about 0.5 ㏈ insertion loss at 2.45 ㎓. And also the high/low-pass balun had the insertion loss less than 0.5 ㏈ and the phase difference of 182 degrees at 2.45 ㎓.