• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.65 no.7
• /
• pp.1169-1175
• /
• 2016

As an Increased penetration level of renewable resources has caused concerns about primary frequency response, an increase in BESS(Battery Energy Storage System) capacity has been expected because of its fast response to the disturbances in the power system. This paper proposes the Integrated Control Strategy of multiple BESS for effectively providing the primary frequency control in the bulk power systems by coordinating the response, SOC and its recovery of BESS. The proposed strategy prevents multiple BESS from providing exceeding response and keeps the balance between SOC of multiple BESS. In addition, It would recover the SOC of BESS efficiently. The effectiveness of the proposed strategy is verified through various case studies employing Korean power system.

• Journal of Power Electronics
• /
• v.18 no.1
• /
• pp.225-233
• /
• 2018

This paper proposes a universal system control strategy for voltage source converter (VSC) based high voltage direct current (HVDC) systems. The framework of the designed control strategy consists of five layer structures considering the topology and control characteristics of the VSC-HVDC system. The control commands sent from the topmost layer can be transmitted to the next layer based on the existing communication system. When the commands are sent to each substation, the following transmission of commands between the four lower layers are realized using the internal communication system while ignoring the communication delay. This hierarchical control strategy can be easily applied to any VSC-HVDC system with any topology. Furthermore, an integrated controller for each converter is designed and implemented considering all of the possible operating states. The modular-designed integrated controller makes it quite easy to extend its operating states if necessary, and it is available for any kind of VSC. A detailed model of a VSC-HVDC system containing a DC hub is built in the PSCAD/EMTDC environment. Simulation results based on three operating conditions (the start-up process, the voltage margin control method and the master-slave control method) demonstrate the flexibility and validity of the proposed control strategy.

• International Journal of Aeronautical and Space Sciences
• /
• v.12 no.1
• /
• pp.43-56
• /
• 2011

An integrated system composed of guidance, navigation and control (GNC) system for autonomous proximity operations and the docking of two spacecraft was developed. The position maneuvers were determined through the integration of the state-dependent Riccati equation formulated from nonlinear relative motion dynamics and relative navigation using rendezvous laser vision (Lidar) and a vision sensor system. In the vision sensor system, a switch between sensors was made along the approach phase in order to provide continuously effective navigation. As an extension of the rendezvous laser vision system, an automated terminal guidance scheme based on the Clohessy-Wiltshire state transition matrix was used to formulate a "V-bar hopping approach" reference trajectory. A proximity operations strategy was then adapted from the approach strategy used with the automated transfer vehicle. The attitude maneuvers, determined from a linear quadratic Gaussian-type control including quaternion based attitude estimation using star trackers or a vision sensor system, provided precise attitude control and robustness under uncertainties in the moments of inertia and external disturbances. These functions were then integrated into an autonomous GNC system that can perform proximity operations and meet all conditions for successful docking. A six-degree of freedom simulation was used to demonstrate the effectiveness of the integrated system.

• Journal of Electrical Engineering and Technology
• /
• v.10 no.3
• /
• pp.847-858
• /
• 2015

Control strategy and corresponding parameters have significant impacts on the overall technical and economic characteristics of composite energy storage systems (CESS). A better control strategy and optimized control parameters can be used to improve the economic and technical characteristics of CESS, and determine the maximum power and stored energy capacity of CESS. A novel coordinated control strategy is proposed considering the coordination of various energy storage systems in CESS. To describe the degree of coordination, a new index, i.e. state of charge coordinated response margin of supercapacitor energy storage system, is presented. Based on the proposed control strategy and index, an optimization model was formulated to minimize the total equivalent cost in a given period for two purposes. The one is to obtain optimal control parameters of an existing CESS, and the other is to obtain the integrated optimal results of control parameters, maximum power and stored energy capacity for CESS in a given period. Case studies indicate that the developed index, control strategy and optimization model can be extensively applied to optimize the economic and technical characteristics of CESS. In addition, impacts of control parameters are discussed in detail.

• Journal of Power Electronics
• /
• v.16 no.6
• /
• pp.2327-2337
• /
• 2016

The mode-switching control of transient process is important to grid-connected 400 Hz solid-state power supply systems. Therefore, this paper analyzes the principle of on-grid and islanding operation of the system with or without local loads in the grid-connected process and provides a theoretical study of the effect of different switching sequences on the mode-switching transient process. The conclusion is that the mode switch (MS) must be turned on before the solid-state switch (STS) in the on-grid process and that STS must be turned off before the MS in the off-grid process. A strategy of mode-switching smooth control for transient process of the system is proposed, including its concrete steps. The strategy utilizes the average distribution of peak currents and the smooth adjustment of peak currents and phases to achieve a no-shock grid connection. The simulation and experimental results show that the theoretical analysis is correct and that the method is effective.

• Journal of Power Electronics
• /
• v.18 no.1
• /
• pp.251-265
• /
• 2018

To enable a master-slave control independent microgrid system (MSCIMGS) to supply electricity continuously, the microgrid inverter should perform mode transfer between grid-connected and islanding operations. Transient oscillations should be reduced during transfer to effectively conduct a seamless mode transfer. This study uses a typical MSCIMGS as an example and improves the mode transfer strategy in three aspects: (1) adopts a status-tracking algorithm to improve the switching strategy of the outer loop, (2) uses the voltage magnitude and phase pre-synchronization algorithm to reduce transient shock at the time of grid connection, and (3) applies the hybrid-sensitivity $H_{\infty}$ robust controller instead of the current inner loop to improve the robustness of the controller. Simulations and experiments show that the proposed strategy is more practical than the traditional proportional-derivative control mode transfer and effective in reducing voltage and current oscillations during the transfer period.

• Journal of Korean Academy of Nursing
• /
• v.38 no.4
• /
• pp.513-521
• /
• 2008

Purpose: The purpose of this study was to develop an integrated suicide violence prevention program for adolescents. Another purpose was to evaluate the effects of the integrated suicide violence prevention program on self-esteem, parent-child communication, aggression, and suicidal ideation in adolescents. Methods: The study employed a quasi -experimental design. Participants for the study were high school students, 24 in the experimental group and 25 in the control group. Data was analyzed by using the SPSS/WIN. 11.5 program with $X^2$ test, t-test, and 2-way ANOVA. Results: Participants in the integrated suicide violence prevention program reported increased self-esteem scores, which was significantly different from those in the control group. Participants in the integrated suicide violence prevention program reported decreased aggression and suicidal ideation scores, which was significantly different from those in the control group. Conclusion: The integrated suicide violence prevention program was effective in improving self-esteem and decreasing aggression and suicidal ideation for adolescents. Therefore, this approach is recommended as the integrated suicide violence prevention strategy for adolescents.

• Journal of Electrical Engineering and Technology
• /
• v.10 no.5
• /
• pp.1969-1982
• /
• 2015

The virtual inertia control (VIC) of wind turbine with directly-driven permanent-magnet synchronous generator (D-PMSG) can act similarly to the conventional synchronous generator in inertia response and frequency control, thereby supporting the system frequency stability. However, because the wind speed is inconstant and changeable to a certain extent and the D-PMSG is a complex nonlinear system, there are great difficulties in the virtual inertia optimal control of the D-PMSG. Based on the design principle of the active disturbance rejection control (ADRC), this paper presents a new VIC strategy for the D-PMSG from the perspective of power disturbance suppression in the system. The strategy helps fulfill the power grid disturbance estimation and compensation by means of the extended state observer (ESO) so as to improve the disturbance-resisting performance of the system. Compared with conventional proportional-derivative virtual inertia control (PDVIC), this method, which is of better adaptability and robustness, can not only improve the property of the D-PMSG responding to the system frequency but also reduce the influence of wind speed disturbance. The simulation and experiment results have verified the effectiveness and feasibility of the VIC based on the ADRC.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2010.05a
• /
• pp.1041-1042
• /
• 2010

• 제어로봇시스템학회:학술대회논문집
• /
• 1991.10a
• /
• pp.935-938
• /
• 1991

We are developing an automatic adjusting system for ITC. ITC(Integrated Tube Components) has a large set-by-set variability in its characteristics. And it also has nonlinearities. It requires not only a fast vision process but also an efficient control algorithm to meet the need for high productivity. In this paper, the description of an adjusting system and the modelling of ITC will be presented. And also the concept of a new rule based hierarchical algorithmic approaches will be suggested.