• 한국전산유체공학회:학술대회논문집
• /
• 2010.05a
• /
• pp.473-478
• /
• 2010

In this study, the Ergun's equation has been verified in order to calculate pressure drop of the two phase flow. The equation had been used in the high Reynolds number region for interior ballistic analysis in spite of being verified in the low Reynolds number region. Therefore additional verification seems to be inevitable. Thus, the validity of the equation has been verified using CFD in the high Reynolds number cases of the diameter-particle ratio 10, 13 and 16.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.40 no.2
• /
• pp.229-236
• /
• 2016

For this research, the trajectory of a projectile was simulated via the multibody dynamics analysis of a self-propelled mortar. The dynamic model was composed of a mortar model and a vehicle model, and was simulated using the RecurDyn program. Interior ballistic was applied to the mortar model, and exterior ballistic was conducted by Matlab using the simulation results of the interior trajectory. Through repetitive Monte-Carlo simulations, the accuracy of the mortar was analyzed by considering variations in the aiming angle and vehicle dynamic response.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.18 no.8
• /
• pp.2201-2209
• /
• 1994

Macroscopic combustion models used in gun interior ballistic codes are discussed and experimental methods to measure propellant burning rate are reviewed. Comparing with gun firing results, the limit of combustion model is shown and modified combustion model is proposed. But combustion model should be selected with respect to total gun system including propellants.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2003.10a
• /
• pp.47-50
• /
• 2003

JA2 Propellants, made by non-solvent process, are of great interest for the tank gun propellant. This is due to high energy. The grain geometries of JA2 and modified JA2 propellant were designed for application to 105mm APFSDS projectile. The combustion, thermochemical, and interior ballistic properties of the propellant were tested and calculated. The performances of the propellant were evaluated out using 105mm slug T2 projectiles and 105mm tank gun. The muzzle velocity of the propellants was higher than that of the KM30 for K274 projectile.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.22 no.3
• /
• pp.251-258
• /
• 2009

At the stage conceptual design, combat vehicle is classified into three general categories of fire power, mobility and physical properties of system. The present research is restricted to fire power and its optimization. At the stage of conceptual designing of system, it is appropriate to consider major variables affecting fire power - including the weight of bullet, which exerts a direct influence on destroying effect, maximum range which takes long range firing in consideration. To estimate the maximum firing range, a simple interior ballistic and an exterior ballistic model were built by using the lumped parameter method, Le Duc method and point mass trajectory model. Design of experiment and regression analysis was used to derive simulations of fire power. Finally, response surface models were built and design variables were analyzed.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2010.11a
• /
• pp.668-671
• /
• 2010

Comparative study on propellant modeling has been investigated using a non-dimensional method and an one-dimensional method. The propellant location in the chamber can not be described by the non-dimensional method. It is, however, possible for the one-dimensional method to describe. Therefore, the analysis of the interior ballistics according to the propellant arrangements has been performed by the one-dimensional method. The negative differential pressure in the chamber could be predicted and the necessity of the one-dimensional modeling for the analysis of the interior ballistics has been confirmed.

• Korean Journal of Computational Design and Engineering
• /
• v.19 no.4
• /
• pp.316-323
• /
• 2014

This paper proposes the 3D modeling and simulation technique for predicting the integrated performance of combat vehicle. To consider the practical driving and firing condition of a combat vehicle, the full vehicle model, which can define the six degrees-of-freedom of vehicle motion and various firing angles, is developed. The critical design parameters such as the stiffness and damping coefficient of suspension system are applied to construct the analysis model of vehicle. A simple ballistic model, which incorporates the empirical interior ballistic model and the point mass trajectory model, is built to estimate the firing range and the firing recoil force. To predict the integrated performance and analyze the effect of system parameters, MATLAB/SIM-ULINK model of a combat vehicle for performing the real time simulation is also developed. Several simulation tests incorporating the road bump and the firing recoil force are presented to confirm the effectiveness of the proposed vehicle model.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.10 no.3
• /
• pp.208-216
• /
• 2007

As the propellant mass is being accelerated out of the gun chamber along with the projectile, a continuous pressure gradient exists between the end of chamber and the base of the projectile. For this reason, the base pressure-travel curve is very important to design a conventional gun barrel in the interior ballistics, but it is not obtained briefly by empirical or theoretical method. In this paper, a simple relation between chamber pressure and base pressure was determined by the factor of base pressure(Cb) obtained from the experimental method. The simple relation gives a reasonable prediction for the reduction of pressure between the breech and the base of projectile owing to the axial gradient in the gun tube. The predictions have been validated by the infrared screen sensor and the PRODAS(PROjectile Design and Analysis System) for interior ballistic systems. Therefore, the base pressure-travel curve could be calculated from the chamber pressure measured by piezoelectric sensor. The base pressure-travel curve obtained from the simple relation offers initial information to gun barrel designer and is used for calculation of muzzle velocity.

• 한국전산유체공학회:학술대회논문집
• /
• 2011.05a
• /
• pp.41-45
• /
• 2011

Pressure drops of two-phase flow in a pipe according to particle shapes have been calculated and analyzed. The numerical analysis for 3 cases of Reynolds number has been conducted for each particle shape. In case of the cylinder shape, the particles had been assumed to be randomly distributed for each Reynolds number. The results have been averaged and compared to those of the case of the ball shape. Additionally, pressure drops of ball and cylinder shapes has been compared to the result of Ergun's equation.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.14 no.6
• /
• pp.1166-1170
• /
• 2011

For developing the ignition device for the interceptor of Korean active protection system, the design parameters of the ignition device which should have a short ignition delay time and sufficient energy for propellant ignition were studied. The electric primer instead of mechanical primer was adopted for deceasing delay time, and ignition code was used for decreasing the time difference of flame propagation from the flame holes. The developed ignition device showed the ignition delay time of a few ms. When the designed ignition device was applied to the open-type propulsion devices, the stable interior ballistic characteristic was showed in a firing test.